表4.4.1方(矩)形管道檢驗批施工質量驗收表

1、方（矩）形管道檢驗批施工質量驗收表inspection of construction quality test table機組工程編號project number:性質property:表4.4.1分項工程名稱name of sub-item project序號sr.檢 驗項目 inspection items性質property單位unit質量標準 quality standard質量檢驗結果the quality inspection results結論conclusion1原材料品種、規格、性能type, specifications , performance ofraw mater

2、ial主控maincontrol應符合現行國家產品標準和設計 要求。進口鋼材產品質量應符合設 計要求和合同規定標準的規定products should be consistent with existing national standards and design requirements. quality of imported steel products should comply with the design requirements and provisions of the standard stipulated in the contract2原材料尺寸偏差size devi

3、ationof raw material應符合產品標準的規定 shouldcomply with the regulations of the product standard3原材料表面外觀質量theappearance quality of the raw material surface應符合現行有關標準的規定should comply with the terms of the current relevant standards4截面邊長偏差cross section length deviationmm+ li/500 ,且 and045截面兩對角線差主控maincontrolmm

4、 li/250 ,且 and086兩端面與軸線垂直度偏差twoend face and axis verticality deviationmm li/100 ,且 and 57管道長度偏差mm0l2/500 ,且 and0108管道直線度偏差straightness deviation主控maincontrolmm l2/500 ,且 and069對口錯邊量align deviationvalues. 10mmmm 10mm0.1 s分項工程名稱name of sub-item project序號sr.檢 驗項目 inspection items性質property單位unit質量標準 qu

5、ality standard質量檢驗結果the quality inspection results結論conclusion10表面平面度偏差 surfaceflatnessdeviations. 5mmmm/m 5mm511加固筋位置偏差 strengthening ribposition deviationmm512內支撐相對于加固筋中心位置 偏差mm513焊焊接材料的品種、規格、性 能 type, specification, performance of weldingmaterial主控maincontrol應符合設計要求和現行國家產品標準的規定 should comply with

6、 the design requirements and the provisions of the existing national product standards14接 w el di ng接頭表面質量joint surfacequality焊縫尺寸weldseam size主控maincontrol應符合設計要求 should comply with the design requirements15焊縫成型weld seam formation焊縫過渡圓滑，接頭良好weld seamtransits smoothly, and joint well16裂紋、氣孔和夾 渣 flaw

7、, crater, blowhole and slag inclusion無no17嚴密性主控main control無滲漏no leakage18油 漆paint油漆的品種、規格、性能 type , specifications , performance of paint主控maincontrol應符合設計要求和現行國家產品標準的規定 should comply with the design requirements and the provisions of the existing national product standards19涂裝前鋼材表面除銹remove the cor

8、rosion on the steel material before painting應符合設計要求和現行國家有關標準的規定 should comply with design requirement and provisions of the existing national standards20底層防銹漆涂刷apply anti-rust paint at bottom layer涂刷均勻、無透底、漏刷 paintevenly, and no leakage注：li為設計邊長；lz為管道設計長度；s為管道壁板厚度。li is design height; s is pipe wall thickness;分項工程名稱name of sub-item project序號sr.檢 驗項目 inspection items性質property單位unit質量標準 quality standard質量檢驗結果the quality inspection results結論conclusion驗收結論：acceptance conclusion監理單位 supervision unit :驗收單位 acceptance of t