嵌入式系統設計與開發教程 課件 第5章 基于Linux的驅動程序設計-2

編寫PWM驅動以及測試程序開發板的BEEP燈電路在Exynos4412中，一共有5個32位定時器，這些定時器課發送中斷信號給ARM處理器，另外，定時器0、1、2、3包含了脈沖寬度調制（PWM），并可驅動其對應的I/O引腳。每個定時器都有一個獨立的32位遞減計數器，定時器啟動后，計數緩沖寄存器（TCNTBn）將初始值加載到遞減計數器，定時器時鐘驅動遞減計數器，當遞減計數器達到零，自動產生計時器中斷請求，同時相應TCNTBn的值自動重新加載，開始下一個循環。但是，如果定時器停止，如清除TCONn的定時器使能位，TCNTBn的值將不會重新加載到計數器中。每個定時器都有一個獨立的32位比較緩沖寄存器（TCMPBn）。當遞減計數器與定時器控制邏輯中比較寄存器的值相匹配時，PWM輸出會產生由低到高的電平跳變，因此，比較寄存器決定PWM輸出的開啟時間或關閉時間。1、初始化定時器n對應的計數緩沖寄存器TCNTBn為159，定時器n對應的計數比較緩沖寄存器TCMPBn為109。2、啟動定時器n：設置定時器n的啟動位為1，并手動更新為為零。此時寄存器TCNTBn的值159自動加載到內部的遞減寄存器中，并開始遞減計數，同時輸出引腳TOUTn輸出低電平。3、當遞減寄存器的值遞減到109（TCMPBn的數值）時，定時器n對應的電平輸出引腳TOUTn從低電平翻轉到高電平。4、當遞減寄存器的值遞減到0時，計數緩沖寄存器TCNTBn的值159重新被加載到定時器的遞減器，定時器n對應的電平輸出引腳TOUTn重新輸出低電平，這樣流程重復進行，引腳TOUTn就輸出占空比可控的PWM波。值得注意的是，修改計數緩沖寄存器TCNTBn或比較緩沖寄存器TCMPBn的值，只能在下一個PWM周期起作用，不影響當前周期PWM的占空比。PWM驅動源程序文件（pwm_dev.c）設計，關鍵步驟為：pwm_dev_open：主要實現對PWM的寄存器進行初始化工作，pwm_dev_release：主要實現停止PWM波形的輸出，pwm_dev_ioctl：分別設置了四個命令實現PWM的啟動，停止，設置分頻系數以及設置頻率。在驅動加載時，即pwm_dev_init函數中，將實例化的文件操作結構體pwm_ops與設備號關聯并注冊到內核中，同時生成對應的設備文件。#include<linux/module.h>#include<linux/kernel.h>#include<linux/init.h>#include<linux/platform_device.h>#include<linux/fb.h>#include<linux/err.h>#include<linux/slab.h>#include<linux/delay.h>#include<linux/gpio.h>#include<mach/gpio.h>#include<plat/gpio-cfg.h>

MODULE_LICENSE("GPLv2");

#defineDEVICE_NAME "pwm"http://定義設備的名字為

pwm#defineDEVICE_NUM 1staticintmajor=0;//主設備號，次設備號staticintminor=0;

structcdevpwm_dev_cdev;staticstructclass*pwm_class;

pwm_dev.c

#defineNS_IN_1HZ 0x6400//100MHz/256/16

#defineBUZZER_PMW_GPIO EXYNOS4_GPD0(0)//蜂鳴器GPIO配置

#defineTIMER_BASE 0X139D0000void__iomem *timer_base;#defineTCFG0 (void__iomem *)(timer_base+0X00)#defineTCFG1 (void__iomem *)(timer_base+0X04)#defineTCON (void__iomem *)(timer_base+0X08)#defineTCNTB1 (void__iomem *)(timer_base+0X0C)#defineTCMPB1 (void__iomem *)(timer_base+0X10)

#definePWM_ON _IO('K',0)#definePWM_OFF _IO('K',1)#definePWM_SET_PRE _IOW('K',2,int)#definePWM_SET_FREQ _IOW('K',3,int)//open方法函數，主要打開pwm的操作staticintpwm_dev_open(structinode*inode,structfile*file){ printk(KERN_INFO"pwm_openstart"); s3c_gpio_cfgpin(BUZZER_PMW_GPIO,S3C_GPIO_SFN(2));

writel(readl(TCFG0)|0xff,TCFG0); writel((readl(TCFG1)&(~0x0f))|0x04,TCFG1); writel(300,TCNTB1); writel(150,TCMPB1); writel((readl(TCON)&(~0x1f))|0X02,TCON); return0;}//close方法函數，主要是關閉pwm操作staticintpwm_dev_release(structinode*inode,structfile*file){ printk(KERN_INFO"pwm_close"); writel(readl(TCON)&(~0x1f),TCON); s3c_gpio_cfgpin(BUZZER_PMW_GPIO,S3C_GPIO_OUTPUT); return0;}//控制io口方法函數staticlongpwm_dev_ioctl(structfile*filep,unsignedintcmd,unsignedlongarg){ intdata=arg;

if(_IOC_TYPE(cmd)!='K') return-ENOTTY; if(_IOC_NR(cmd)>3) return-ENOTTY;

printk(KERN_INFO"pwm_ioctlstart");

switch(cmd){ casePWM_ON: writel((readl(TCON)&(~0x1f))|0X0D,TCON); break; casePWM_SET_PRE: if(data==0) return-EINVAL; writel(readl(TCON)&(~0x1f),TCON); writel((readl(TCFG0)&(~0xff))|(data&0xff),TCFG0); writel((readl(TCON)&(~0x1f))|0X0D,TCON); break; casePWM_SET_FREQ: if(data==0) return-EINVAL;data=(NS_IN_1HZ)/data; writel(data,TCNTB1); writel(data>>1,TCMPB1); break; casePWM_OFF: writel(readl(TCON)&(~0x1f),TCON); break; } return0;}//operations結構體staticstructfile_operationspwm_ops={ .owner=THIS_MODULE, .unlocked_ioctl=pwm_dev_ioctl, .open=pwm_dev_open, .release=pwm_dev_release};

//pwm設備初始化,設備在被insmod插入模塊到內核的過程中會調用這個函數staticint__initpwm_dev_init(void){ intret=0; dev_tdevno; printk(KERN_INFO"pwm_dev_initstart");

gpio_free(BUZZER_PMW_GPIO); ret=gpio_request(BUZZER_PMW_GPIO,DEVICE_NAME);

if(ret){ printk(KERN_INFO"requestGPIO%dforpwmfailed\n",BUZZER_PMW_GPIO); gotoERR1; } s3c_gpio_cfgpin(BUZZER_PMW_GPIO,S3C_GPIO_OUTPUT); gpio_set_value(BUZZER_PMW_GPIO,0);/*動態注冊設備號*/ ret=alloc_chrdev_region(&devno,minor,DEVICE_NUM,"pwmdriver"); /*獲得主設備號*/ major=MAJOR(devno); printk(KERN_INFO"dynamicadev_regionmajoris%d!\n",major); if(ret<0){ printk(KERN_INFO"register_chrdev_regionreq%disfailed!\n",major); gotoERR2;}else{ cdev_init(&pwm_dev_cdev,&pwm_ops); pwm_dev_cdev.owner=THIS_MODULE; ret=cdev_add(&pwm_dev_cdev,devno,DEVICE_NUM); if(ret<0){ printk(KERN_INFO"cdev_add%disfailed!\n",ret); gotoERR3; } else{ pwm_class=class_create(THIS_MODULE,DEVICE_NAME); device_create(pwm_class,NULL,devno,NULL,DEVICE_NAME); }}//地址映射timer_base=ioremap(TIMER_BASE,0x20);if(timer_base==NULL){ printk(KERN_INFO"ioremapfailed!\n"); ret=-ENOMEM; gotoERR4;} printk(KERN_INFODEVICE_NAME"\tinitialized\n");return0;

ERR4: device_destroy(pwm_class,devno); class_unregister(pwm_class); class_destroy(pwm_class); cdev_del(&pwm_dev_cdev);ERR3: unregister_chrdev_region(devno,DEVICE_NUM);ERR2: gpio_free(BUZZER_PMW_GPIO);ERR1: returnret;}

//設備在被卸載rmmod的過程中會調用這個函數staticvoid__exitpwm_dev_exit(void){ dev_tdevno=MKDEV(major,minor);

printk("pwm_exitstart");

gpio_free(BUZZER_PMW_GPIO); device_destroy(pwm_class,devno); class_unregister(pwm_class); class_destroy(pwm_class); cdev_del(&pwm_dev_cdev); unregister_chrdev_region(devno,DEVICE_NUM); iounmap(timer_base); printk(KERN_INFO"pwm_dev_exit!\n"); return;}

//模塊初始化module_init(pwm_dev_init);//銷毀模塊module_exit(pwm_dev_exit);Makefileobj-m=pwm_dev.oKERNELDIR:=/root/yizhi/boot-kernel-source/iTop4412_Kernel_3.0PWD:=$(shellpwd)modules: $(MAKE)-C$(KERNELDIR)M=$(PWD)modulesclean: rm-rf*.o~core.depend*.ko*.mod.c*.*.cmd rm–rf.tmp_versions要編譯的結果，名字和驅動源程序相同在PWM測試應用程序中，根據PWM驅動設計的3個文件操作open、close、ioctl，操作對應的PWM設備驅動文件/dev/pwm，來實現對PWM的控制。本例中，通過PWM驅動設置不同音調的頻率，以及設置不同頻率的播放時間，實現控制蜂鳴器輸出音樂旋律。/*pwm_music.c*/#include<stdio.h>#include<stdlib.h>#include<unistd.h>#include<fcntl.h>#include<string.h>#include<sys/types.h>#include<sys/stat.h>#include<sys/ioctl.h>#include"pwm_music.h“intmain(){inti=0;intdev_fd;intpre=255;arm-none-linux-gnueabi-gcc–opwm_musicpwm_music.cdev_fd=open("/dev/pwm",O_RDWR|O_NONBLOCK);if(dev_fd<0){printf("error!\n");return-1;}ioctl(dev_fd,PWM_ON);ioctl(dev_fd,PWM_SET_PRE,pre);for(i=0;i<sizeof(Twotigers)/sizeof(Note);i++){ ioctl(dev_fd,PWM_SET_FREQ,Twotigers[i].pitch); usleep(Twotigers[i].dimation*50);}ioctl(dev_fd,PWM_OFF);close(dev_fd);return0;}打開pwm設置基本頻率播放音調音調的持續時間停止pwm/*pwm_music.h*/#ifnd