帶式輸送機幾種軟起動方式的比較外文翻譯/中英文翻譯/外文文獻翻譯

外文原文： A Comparison of Soft Start Mechanisms for Mining Belt Conveyors 1800 Washington Road Pittsburgh, PA 15241 Belt Conveyors are an important method for transportation of bulk materials in the mining industry. The control of the application of the starting torque from the belt drive system to the belt fabric affects the performance, life cost, and reliability of the conveyor. This paper examines applications of each starting method within the coal mining industry. INTRODUCTION The force required to move a belt conveyor must be transmitted by the drive pulley via friction between the drive pulley and the belt fabric. In order to transmit power there must be a difference in the belt tension as it approaches and leaves the drive pulley. These conditions are true for steady state running, starting, and stopping. Traditionally, belt designs are based on static calculations of running forces. Since starting and stopping are not examined in detail, safety factors are applied to static loadings (Harrison, 1987). This paper will primarily address the starting or acceleration duty of the conveyor. The belt designer must control starting acceleration to prevent excessive tension in the belt fabric and forces in the belt drive system (Suttees, 1986). High acceleration forces can adversely affect the belt fabric, belt splices, drive pulleys, idler pulleys, shafts, bearings, speed reducers, and couplings. Uncontrolled acceleration forces can cause belt conveyor system performance problems with vertical curves, excessive belt take-up movement, loss of drive pulley friction, spillage of materials, and festooning of the belt fabric. The belt designer is confronted with two problems, The belt drive system must produce a minimum torque powerful enough to start the conveyor, and controlled such that the acceleration forces are within safe limits. Smooth starting of the conveyor can be accomplished by the use of drive torque control equipment, either mechanical or electrical, or a combination of the two (CEM, 1979). SOFT START MECHANISM EVALUATION CRITERION What is the best belt conveyor drive system? The answer depends on many variables. The best system is one that provides acceptable control for starting, running, and stopping at a reasonable cost and with high reliability (Lewdly and Sugarcane, 1978). Belt Drive System For the purposes of this paper we will assume that belt conveyors are almost always driven by electrical prime movers (Goodyear Tire and Rubber, 1982). The belt drive system shall consist of multiple components including the electrical prime mover, the electrical motor starter with control system, the motor coupling, the speed reducer, the low speed coupling, the belt drive pulley, and the pulley brake or hold back (Cur, 1986). It is important that the belt designer examine the applicability of each system component to the particular application. For the purpose of this paper, we will assume that all drive system components are located in the fresh air, non-permissible, areas of the mine, or in non-hazardous, National Electrical Code, Article 500 explosion-proof, areas of the surface of the mine. Belt Drive Component Attributes Size. Certain drive components are available and practical in different size ranges. For this discussion, we will assume that belt drive systems range from fractional horsepower to multiples of thousands of horsepower. Small drive systems are often below 50 horsepower. Medium systems range from 50 to 1000 horsepower. Large systems can be considered above 1000 horsepower. Division of sizes into these groups is entirely arbitrary. Care must be taken to resist the temptation to over motor or under motor a belt flight to enhance standardization. An over motored drive results in poor efficiency and the potential for high torques, while an under motored drive could result in destructive overspending on regeneration, or overheating with shortened motor life (Lords, et al., 1978). Torque Control. Belt designers try to limit the starting torque to no more than 150% of the running torque (CEMA, 1979； Goodyear, 1982). The limit on the applied starting torque is often the limit of rating of the belt carcass, belt splice, pulley lagging, or shaft deflections. On larger belts and belts with optimized sized components, torque limits of 110% through 125% are common (Elberton, 1986). In addition to a torque limit, the belt starter may be required to limit torque increments that would stretch belting and cause traveling waves. An ideal starting control system would apply a pretension torque to the belt at rest up to the point of breakaway, or movement of the entire belt, then a torque equal to the movement requirements of the belt with load plus a constant torque to accelerate the inertia of the system components from rest to final running speed. This would minimize system transient forces and belt stretch (Shultz, 1992). Different drive systems exhibit varying ability to control the application of torques to the belt at rest and at different speeds. Also, the conveyor itself exhibits two extremes of loading. An empty belt normally presents the smallest required torque for breakaway and acceleration, while a fully loaded belt presents the highest required torque. A mining drive system must be capable of scaling the applied torque from a 2/1 ratio for a horizontal simple belt arrangement, to a 10/1 ranges for an inclined or complex belt profile. Thermal Rating. During starting and running, each drive system may dissipate waste heat. The waste heat may be liberated in the electrical motor, the electrical controls, the couplings, the speed reducer, or the belt braking system. The thermal load of each start Is dependent on the amount of belt load and the duration of the start. The designer must fulfill the application requirements for repeated starts after running the conveyor at full load. Typical mining belt starting duties vary from 3 to 10 starts per hour equally spaced, or 2 to 4 starts in succession. Repeated starting may require the dreading or over sizing of system components. There is a direct relationship between thermal rating for repeated starts and costs. Variable Speed. Some belt drive systems are suitable for controlling the starting torque and speed, but only run at constant speed. Some belt applications would require a drive system capable of running for extended periods at less than full speed. This is useful when the drive load must be shared with other drives, the belt is used as a process feeder for rate control of the conveyed material, the belt speed is optimized for the haulage rate, the belt is used at slower speeds to transport men or materials, or the belt is run a slow inspection or inching speed for maintenance purposes (Hager, 1991). The variable speed belt drive will require a control system based on some algorithm to regulate operating speed. Regeneration or Overhauling Load. Some belt profiles present the potential for overhauling loads where the belt system supplies energy to the drive system. Not all drive systems have the ability to accept regenerated energy from the load. Some drives can accept energy from the load and return it to the power line for use by other loads. Other drives accept energy from the load and dissipate it into designated dynamic or mechanical braking elements. Some belt profiles switch from motoring to regeneration during operation. Can the drive system accept regenerated energy of a certain magnitude for the application? Does the drive system have to control or modulate the amount of retarding force during overhauling? Does the overhauling occur when running and starting? Maintenance and Supporting Systems. Each drive system will require periodic preventative maintenance. Replaceable items would include motor brushes, bearings, brake pads, dissipation resistors, oils, and cooling water. If the drive system is conservatively engineered and operated, the lower stress on consumables will result in lower maintenance costs. Some drives require supporting systems such as circulating oil for lubrication, cooling air or water, environmental dust filtering, or computer instrumentation. The maintenance of the supporting systems can affect the reliability of the drive system. Cost. The drive designer will examine the cost of each drive system. The total cost is the sum of the first capital cost to acquire the drive, the cost to install and commission the drive, the cost to operate the drive, and the cost to maintain the drive. The cost for power to operate the drive may vary widely with different locations. The designer strives to meet all system performance requirements at lowest total cost. Often more than one drive system may satisfy all system performance criterions at competitive costs. Complexity. The preferred drive arrangement is the simplest, such as a single motor driving through a single head pulley. However, mechanical, economic, and functional requirements often necessitate the use of complex drives. The belt designer must balance the need for sophistication against the problems that accompany complex systems. Complex systems require additional design engineering for successful deployment. An often-overlooked cost in a complex system is the cost of training onsite personnel, or the cost of downtime as a result of insufficient training. SOFT START DRIVE CONTROL LOGIC Each drive system will require a control system to regulate the starting mechanism. The most common type of control used on smaller to medium sized drives with simple profiles is termed Open Loop Acceleration Control. In open loop, the control system is previously configured to sequence the starting mechanism in a prescribed manner, usually based on time. In open loop control, drive-operating parameters such as current, torque, or speed do not influence sequence operation. This method presumes that the control designer has adequately modeled drive system performance on the conveyor. For larger or more complex belts, Closed Loop or Feedback control may he utilized. In closed loop control, during starting, the control system monitors via sensors drive operating parameters such as current level of the motor, speed of the belt, or force on the belt, and modifies the starting sequence to control, limit, or optimize one or wore parameters. Closed loop control systems modify the starting applied force between an empty and fully loaded conveyor. The constants in the mathematical model related to the measured variable versus the system drive response are termed the tuning constants. These constants must be properly adjusted for successful application to each conveyor. The most common schemes for closed loop control of conveyor starts are tachometer feedback for speed control and load cell force or drive force feedback for torque control. On some complex systems, It is desirable to have the closed loop control system adjust itself for various encountered conveyor conditions. This is termed Adaptive Control. These extremes can involve vast variations in loadings, temperature of the belting, location of the loading on the profile, or multiple drive options on the conveyor. There are three common adaptive methods. The first involves decisions made before the start, or Restart Conditioning. If the control system could know that the belt is empty, it would reduce initial force and lengthen the application of acceleration force to full speed. If the belt is loaded, the control system would apply pretension forces under stall for less time and supply sufficient torque to adequately accelerate the belt in a timely manner. Since the belt only became loaded during previous running by loading the drive, the average drive current can be sampled when running and retained in a first-in-first-out buffer memory that reflects the belt conveyance time. Then at shutdo the FIFO average may be use4 to precondition some open loop and closed loop set points for the next start. The second method involves decisions that are based on drive observations that occur during initial starting or Motion Proving. This usually involves a comparison In time of the drive current or force versus the belt speed. if the drive current or force required early in the sequence is low and motion is initiated, the belt must be unloaded. If the drive current or force required is high and motion is slow in starting, the conveyor must be loaded. This decision can be divided in zones and used to modify the middle and finish of the start sequence control. The third method involves a comparison of the belt speed versus time for this start against historical limits of belt acceleration, or Acceleration Envelope Monitoring. At start, the belt speed is measured versus time. This is compared with two limiting belt speed curves that are retained in control system memory. The first curve profiles the empty belt when accelerated, and the second one the fully loaded belt. Thus, if the current speed versus time is lower than the loaded profile, it may indicate that the belt is overloaded, impeded, or drive malfunction. If the current speed versus time is higher than the empty profile, it may indicate a broken belt, coupling, or drive malfunction. In either case, the current start is aborted and an alarm issued. CONCLUSION The best belt starting system is one that provides acceptable performance under all belt load Conditions at a reasonable cost with high reliability. No one starting system meets all needs. The belt designer must define the starting system attributes that are required for each belt. In general, the AC induction motor with full voltage starting is confined to small belts with simple profiles. The AC induction motor with reduced voltage SCR starting is the base case mining starter for underground belts from small to medium sizes. With recent improvements, the AC motor with fixed fill fluid couplings is the base case for medium to large conveyors with simple profiles. The Wound Rotor Induction Motor drive is the traditional choice for medium to large belts with repeated starting duty or complex profiles that require precise torque control. The DC motor drive, Variable Fill Hydrokinetic drive, and the Variable Mechanical Transmission drive compete for application on belts with extreme profiles or variable speed at running requirements. The choice is dependent on location environment, competitive price, operating energy losses, speed response, and user familiarity. AC Variable Frequency drive and Brush less DC applications are limited to small to medium sized belts that require precise speed control due to higher present costs and complexity. However, with continuing competitive and technical improvements, the use of synthesized waveform electronic drives will expand. 譯文： 煤礦業帶式輸送機幾種軟起動方式的比較 統一公司 1800 年華盛頓路匹茲堡 , PA 15241帶式運送機是采礦工業運輸大批原料的重要方法。從傳送帶驅動系統到傳送帶紋理結構啟動力矩的應用和控制影響著運送機的性能，壽命和可靠性。本文考查了不同啟動方法在煤礦工業帶式運送機中的應用。 簡介 運行帶式運送機的動力必須由驅動滑輪產生，通過滑輪和傳送帶之間的摩擦力來傳遞。為了傳遞能量，傳送帶上面的張力在接近滑輪部分和離開滑輪部分必定存在著差別。這種差別在穩定運行、啟動和停止時刻都是真實存在的 。傳統傳送帶結構的設計，都是根據穩定運行情況下傳送帶的受力情況。因?yàn)樵O(shè)計過程中沒有詳盡研究傳送帶啟動和停止階段的受力情況，所有的安全措施都集中在穩定運行階段（ Harrison 1987）。本文主要集中講述傳送機啟動和加速階段的特性。傳送帶設計者在設計時必須考慮控制啟動階段的加速狀況，以免使傳送帶和傳送機驅動系統產生過大的張力和動力（ Suttees， 1986）。大加速度產生的動力會給傳送帶的紋理、傳送帶結合處、驅動滑輪、軸承、減速器以及耦合器帶來負面影響。毫無控制的加速度產生的動力能夠引起帶式傳送機系統產生諸 多不良問題，比如上下曲線運動、過度傳送帶提升運動、滑輪和傳送帶打滑、運輸原料的溢出和傳送帶結構。傳送帶的設計需要面對兩個問題：第一，傳送帶驅動系統必須能夠產生啟動帶式傳送機的最小轉動力矩；第二，控制加速度產生動力在安全界限內?？梢酝ㄟ^驅動力矩控制設備來完成，控制設備可以是電子手段也可以是機械手段，也可以是兩者的組合（ CEM， 1979）。 本文主要闡述輸送機的開始和加速的過程。傳送帶設計師必須控制開始加速 度防止過度張緊在傳送帶織品和力量在皮帶傳動系統 . 強加速度力量可能有害地影響傳送帶織品，傳送帶接合 ，驅動皮帶輪，更加無所事事的滑輪 , 軸 , 軸承 , 速度還原劑 , 并且聯結。未管制的加速度力量可能造成皮帶輸送機有垂直的曲線的系統性能問題 ,傳送帶緊線器運動 , 驅動皮帶輪摩擦損失 , 材料溢出 , 并且做成花彩傳送帶織品。傳送帶設計員與二個問題被面對 , 皮帶傳動系統必須導致極小的扭矩足夠強有力開始傳動機 , 和控制了這樣加速度強制是在安全限額內。光滑開始傳動機可能由對驅動器扭矩控制設備的用途 , 或機械或電子 , 或組合的二完成 (CEM 1979) 。 軟起動結構評估標準 什么是最佳的皮帶輸送機驅動系統 ? 答案取決于許多變量。最佳的系統是一個為開始 , 運行 , 和終止提供可接受的控制在合理的費用和以及高可靠性。皮帶傳動系統為本文我們考慮的設計方案 , 皮帶輸送機被電子頭等搬家工人幾乎總驅動。傳送帶 驅動系統 將包括多個要素包括電子原動力、電子馬達起始者以控制系統 , 馬達聯結、速度還原劑、低速聯結、皮帶傳動滑輪、和滑輪閘 (Cur 1986) 。它重要 , 傳送帶設計員審查各個系統要素的適用性對特殊申請。為本文的目的 , 我們假設 , 所有驅動系統要素設置礦的新鮮空氣 , 非允許 , 面積 ,全國電子編碼 , 條款 500 防爆 , 礦的表面的面積。皮帶傳動要素歸因于范圍。某些驅動器要素是可利用和實用的用不同的范圍。為這論述 , 我們假設那皮帶傳動系統范圍從分?jǐn)?shù)馬力對千位的多個馬力。小驅動系統經常是在 50 馬力以下。中型系統范圍從 50 到 1000 馬力。大型系統可能被考慮在 1000 馬力之上。范圍分部入這些組是整個地任意的。必須被保重抵抗誘惑對超出馬達或在馬達之下傳送帶飛行提高標準化。驅動器結果在粗劣的效率和在高扭矩的潛在 , 當驅動器能導致破壞性超速在再生 , 或過度加熱以變短的馬達壽命。扭矩控制。傳送帶設計員設法限制開始的扭矩到?jīng)]有比 150% 運行中。限額在應用的開始的扭矩經常是傳送帶胴體肉、傳送帶接合、滑輪絕熱材料 ,軸偏折評級。在更大的傳送帶和傳送帶以優化大小的要素 , 扭矩限額 110% 至 125% 是公用。除扭矩限額之外 , 傳送帶起始者必需限制會舒展圍繞和會導致旅行的波浪的扭矩增量。一個理想的開始的控 制系統會適用于資格整個傳送帶的扭矩傳送帶休息由問題的脫離決定 , 或運動 , 然后扭矩相等與傳送帶的運動需求以負荷加上恒定的扭矩從休息加速系統要素的慣性對最終奔跑速度。這使系統臨時強制和傳送帶舒展。不同的驅動系統陳列變化的能力控制扭矩的申請對 傳送帶休息和以不同的速度。并且 , 傳動機陳列裝載二個極端。一條空傳送帶正常存在最小的必需的扭矩為脫離和加速度 , 當一條充分地被裝載的傳送帶存在最高的必需的扭矩。開采驅動系統必須是能稱應用的扭矩從一個 2/1 比率為一個水平的簡單傳送帶安排 , 對一個 10/1 范圍為一個傾斜、復雜傳送帶配置文件。 熱量評級 在開始和運行期間 , 各個驅動系統也許消散廢熱。廢熱也許被解放在電子馬達、電子控制、 , 聯結、速度還原劑 , 或傳送帶制動系統。各個起始時間熱量負荷依靠相當數量傳送帶負荷和起始時間的期限。設計員必須履 行被重復的起始時間的申請需求在運行傳動機以后在全負荷。典型的開采傳送帶開始的責任變化從3到 10 個起始時間每時數等隔 ,或 2到 4 個起始時間在連續。被重復的開始也許要求減稅或系統要素。有一個直接關系在熱量評級為被重復的起始時間和費用之間?？勺兯俣?。一些皮帶傳動系統是適當?shù)臑榭刂崎_始的扭矩和速度 , 但只運行以恒定的速度 。一些傳送帶申請會要求一個驅動系統能運行延長的期間以較不比最高速度。這是有用的當驅動器負荷必須與其它驅動器被共享 ,傳送帶被使用當處理飼養者為被表達的物料的費率控制 , 傳送帶速度被優選為貨車使用費費率 ,傳送帶被使用以慢速運輸人工或材料 , 或傳送帶運行緩慢的檢驗或移動速度為維護目的。可變速度皮帶傳動將要求一個控制系統根據某一算法調控操作速度。再生或翻修負荷。一些傳送帶配置文件存在翻修傳送帶系統用品能量對驅動系統的負荷的潛在。沒有所有驅動系統有能力接受被重新生成的能量從負荷。一些驅動器可能接受能量從負荷和退回它到 輸電線供其它負荷使用。其它驅動器接受能量從負荷和消散它入選定的動態或機械剎車的要素。一些傳送帶描出切換從開汽車對再生在運算期間。驅動系統可能接受有些巨大的被重新生成的能量為申請嗎 ? 驅動系統控制或必須調整相當數量減速的強制在翻修期間嗎 ?翻修發生當運行和 開始 ? 維護和支持系統。各個驅動系統將要求定期預防維護。可替換的項目會包括馬達畫筆、軸承、閘填充、散逸電阻器、油 , 和涼水。如果驅動系統被設計和保守地被管理 , 更低的重音在可消耗導致更低的維修費用。一些驅動器要求支持系統譬如流通的油為潤滑油、冷卻空氣或水 , 環 境塵土過濾 , 或計算機儀器工作。支持