質量保證計劃QAP中英文版

1、精品文檔質量保證計劃quality assurance plan客戶名稱client :項目編號item no. :訂單日期order date:供貨單位 vendor :設備代號code :編制 preparatio n日期date審核check :日期date批準 approval :日期datexxxxxt限公司xxxxxxx co., ltd.i歡迎下載精品文檔1、適用范圍和目的 scope and purpose本質量保證計劃適用于upim目產品的制造、檢驗和驗收。確保該產品的制造、檢驗和驗收符合圖樣、規范、標準的要求。 this quality assurance planis a

2、pplicable to the manufacture, inspection and acceptance of upl project products.to ensure that the manufacture, inspection and acceptance of the products meet the requirements of drawings, specifications and standards2、編制依據compilation basistsg r0004-2009固定式壓力容器安全技術監察規程tsg r0004-2009 supervision regu

3、lations on safety technology for stationary pressure vessels gb150.1150.4-2011壓力容器gb150.1150.4-2011the pressure vessel gb/t18442.15-2011 固定式真空絕熱深冷壓力容器gb/t18442.15-2011 fixed vacuum insulated cryogenic pressure vessel max/sc-2011壓力容器制造質量保證手冊max/sc-2011 pressure vessel manufacturing quality assurance

4、manual3、制造、檢驗依據的標準、規范或技術條件standards, specifications ortechnical conditions on which manufacturing or inspection is based設計圖樣和工藝文件design drawings and process documentstsg r0004-2009固定式壓力容器安全技術監察規程tsg r0004-2009 supervision regulations on safety technology forstationary pressure vessels gb150.1150.4-2

5、011壓力容器gb150.1150.4-2011the pressure vessel gb/t18442.15-2011 固定式真空絕熱深冷壓力容器gb/t18442.15-2011 fixed vacuum insulated cryogenic pressure vessel jb/t4711-2003 壓力容器涂敷與運輸包裝jb/t4711-2003 pressure vessel coating and transportation packaginggb713-2008鍋爐和壓力容器用鋼板gb713-2008 steel plates for boilers and pressur

6、e vesselsgb9948-2006石油裂化用無縫鋼管gb9948-2006 seamless steel pipe for petroleum cracking gb/t14976-2012流體輸送用不銹鋼無縫鋼管gb/t14976-2012 stainless steel seamless steel pipe for fluidconveying nb/t47008-2010承壓設備用碳素鋼和合金鋼鍛件nb/t47008-2010 carbon steel and alloy steel forgings forpressure equipment nb/t47014-2011wel

7、ding process assessment of pressure equipmentnb/t47015-2011壓力容器焊接規程jb/t4730-2005承壓設備無損檢測jb/t4730-2005 nondestructive testing of pressure equipments gb/t25198-201o壓力容器封頭gb/t25198-2010pressure vessel head hg/t2059k20635-2009鋼制管法蘭、墊片、緊固件hg/t20592-20635-2009 steel pipe flanges, gaskets, fasteners hg/t21

8、51右21535-2005鋼制人孔和手孔hg/t2151右21535-2005 steel manholes and hand holes 4、產品主要的技術參數 main technical parameters of products容器類別container classn耐壓試驗壓力pressure test1.94mpa氣密性試驗air tightness test1.64mpa設計溫度design temperature-194 c主體材料body materialsus304最高/最低允許工作溫度max/min allowable operating temperature腐蝕裕量

9、corrosion allowance0 mm介質medium氧、氮最高允許工作壓力maximumallowable working pressure設計壓力design pressure1.64mpa焊接接頭系數welding joint coefficient1最大吊裝質量maximum lifting masskg5、 檢查的總要求 general requirements for inspection5.1、低溫液體儲罐設備的檢驗和試驗應符合設計圖樣、工藝文件及相關標準規范的要求。inspection and test of cryogenic liquid storage tank

10、equipment shall meet the requirements of design drawings, process documents and relevant standards and specifications.5.2、 受壓件的標記及移植、焊工鋼印標記、無損檢測標記應按相應標準的 要求在工件上標出，對于不能打鋼印的零部件應記錄在相應文件中。thelabeling and transplantation of pressed parts, welders stamping marks and non-destructive testing marks shall be

11、marked on the workpiece according to the requirements of the corresponding standards, and the parts that cannot be stamped shall be recorded in the corresponding documents.5.3、 檢驗和試驗的記錄、報告應保存，以便審查和提供給用戶。recordsand reports of inspections and tests shall be kept for review and supply to users.5.4、 按要求

12、設置必要的控制點。set up necessary control points asrequired5.5、 低溫液體儲罐設備的制造、檢驗和驗收應接受監察機構的監督檢驗。 the manufacture, inspection and acceptance of cryogenic liquid storage tank equipment shall be subject to supervision and inspection by supervisory bodies.6、材料檢查要求 material inspection requirements6.1 、材料的采購應符合采購技術

13、條件、設計圖樣和相應規范、標準要求。 material purchasing shall conform to the technical requirements, design drawings, relevant specifications and standards for purchasing.6.2 、材料入廠按采購要求進行檢驗與驗收、復驗。 inspection, acceptance and re-inspection of materials in accordance with procurement requirements6.3 、用于低溫液體儲罐的材料應有質量證明書

14、，證明書中材料化學成分、力學性能、熱處理、狀態、無損檢驗等數據應符合相應標準要求，實物標識與質量證明書中標識應一致。 the materials used for cryogenic liquid storage tanks shall have a certificate of quality. the data of chemical composition, mechanical properties, heat treatment, state and non-destructive inspection of the materials in the certificate shal

15、l meet the requirements of the corresponding standards. the physical identification shall be consistent with the identification in the quality certificate.6.4 、材質證明書應為加蓋制造單位質量檢驗章的原件，若材料從非材料制造單位取得時應當取得材料制造單位提供的質量證明書原件或加蓋材料供應單位檢驗公章和經辦人章的復印 件。質量證明書內容應當齊全、清晰、并且蓋有材料制造單位的檢驗章。 material certificate shall be

16、 the original of the quality inspection seal of the manufacturing unit. if the material is obtained from the non-material manufacturing unit, the original of the quality certificate provided by the material manufacturing unit or the copy of the inspection seal and the operators seal of the material

17、supplying unit shall be obtained. the content of the quality certificate shall be complete, clear and stamped with the inspection stamp of the material manufacturing unit.6.5 、受壓元件用材料未經檢驗或檢驗不合格，不得使用。 materials used for compressed components shall not be used unless they are inspected or unqualified.

18、6.6 、受壓元件用材料應當在合格供方購買。 materials for pressurized components shall be purchased from qualified suppliers 7、焊接檢查要求welding inspection requirements7.1 、有滿足和覆蓋低溫液體儲罐設備的焊接工藝評定。 welding process assessment for equipment with low temperature liquid storage tanks satisfied and covered7.2 、有指導焊接施焊的焊接工藝規程。 weld

19、ing procedures guided for welding7.3 、焊工應具有相應的資格證。 welders shall have appropriate qualification certificates.7.4 損檢測檢查要求non-destructive testing requirements低溫液體儲罐設備的無損檢測的要求應符合設計圖樣、焊接工藝和相關標準的要求。 non-destructive testing of cryogenic liquid storage tank equipment shall meet the requirements of design d

20、rawings, welding process and related standards.7.5 壓試驗withstand voltage test9.1 、制造結束并經綜合檢查合格，各項檢查均已完成。檢驗資料必須齊全、正確，簽章手續完備，方能按圖樣規定的試驗壓力進行耐壓試驗。3歡迎下載精品文檔manufacturing is finished and passed by comprehensive inspection. all inspection has been completed. the test data must be complete and correct, and t

21、he signature procedures are complete, so that the pressure test can be carried out according to the test pressure prescribed in the drawings.9.2 、試驗時應準備兩塊量程相同，且在檢定有效期內的壓力表，壓力表的量程應為1.53倍的試驗壓力，宜為試驗壓力的2倍，壓力表的精度不得低于1.6 級，表盤直徑不得小于100mm。 when testing, two pressure gauges withthe same range should be prepa

22、red, and the range of the pressure gauge should be 1.5-3 times of the test pressure, 2 times of the test pressure, the accuracy of the pressure gauge should not be less than 1.6 grades, and the diameter of the dial should not be less than 100 mm.10、除銹和涂漆rust removal and painting10.1 、容器制造完畢后應按工藝要求進行

23、噴砂除銹。(保護法蘭密封面)。 sandblasting and rust removal shall be carried out after the vessel has been manufactured according to the technological requirements. (protection flange sealing surface)10.2 、容器的油漆.包裝和運輸應符合jb/t4711的要求.具體要求按油漆作 業指導書執行。 paint for containers. packaging and transportation shall comply w

24、ith the requirements of jb/t4711. specific requirements shall be implemented in accordance with the paint operation instructions.11、控制點說明 control point description檢驗點(e點)：是指產品制造過程中的工序或質量項目，由檢驗員進行檢 查的控制點。 inspection point (e point): a control point for inspection by inspectors of processes or quality

25、 items in the manufacturing process of a product.停止點(h點)：停止點是指對產品質量有重大影響的工序，在產品制造進行 到該工序前應通知檢驗員并經檢驗合格簽字后方可進行下道工序。 stop point (h point): stop point refers to the process that has a significant impact on the quality of the product. before the product is manufactured to the process, the inspector shoul

26、d be notified and the next process can be carried out only after the inspection has been qualified and signed.審閱點(r點)：完成某項活動或過程，自檢合格后，由質保體系有關人員通 過查看文件和記錄進行確認。 review point (r point): after completing an activity or process and passing the self-inspection, the relevant personnel of the qa system conf

27、irm it by checking documents and records.見證點(w點)：見證點是指產品制造在規定的關鍵工序施工前，制造廠應提 前通知用戶或第三方檢驗在約定的時間內到現場進行見證和對其施工實施監督。 witness point (w point): witness point refers to that the manufacturer shall notify the user or the third party to inspect theproduct in advance before the construction of the specified ke

28、y process and to witness and supervise its construction within the agreed time.監檢點(a點)：監檢機構監督檢驗點。在產品制造進行到該工序前監檢機構 人員必須到場檢驗，并在提供的見證文件上簽字確認后方可進行下道工序。 inspection point (point a): inspection institutions supervise inspection points. the inspector must be present to inspect the product before it is manuf

29、actured and sign and confirm the testimony documents before proceeding to the next process.監檢點(b點)：監檢機構監督檢驗點。在產品制造進行到該工序前應通知監 檢機構人員到場檢驗，如不能到場監檢，可在受檢企業自檢后，對受檢企業提 供的相應見證文件進行審查并簽字確認。inspection point (point b):inspection institutions supervise inspection points. the inspector should be notified to inspe

30、ct the product before it is manufactured.if the inspector fails to inspect the product on the spot, therelevant witness documents provided by the inspected enterprise can be examined and signed after the inspected enterprise has inspected itself.12、責任崗位代號說明 statement of responsibility position code質

31、量保證責任人 quality assurance responsible person: zr設計責任人 design responsible person : dr 檢查員 inspector : j 材料、零部件責任人 responsible person for materials and parts: cr理化檢驗責任人 person responsible for physical and chemical inspection: lr工藝責任人 technological responsible person : gr 監檢monitoring : cs 檢驗與試驗責任人 insp

32、ection and test responsible person : jr 無損檢測責任人 non-destructive testing responsible person : nr 焊接責任人 welding liability person : wr熱處理責任人 responsible person for heat treatment : rr產前準備控制點明細表list of control points for prenatal preparation序 號質量實施過程項目質量合格標準依據責任者質控見 證類別見證資料執行者驗證者1合同技術協議評審合同控制程序合同簽訂人各部分負責人r評審記錄2產品編號程序文件生產計劃員生產負責人r臺帳3設計資料圖紙審查gb150質量手冊等設計員drr審查記錄4二n性審圖gb15q質量手冊等工幺員grr審查記錄5圖紙認證容規及相關標準質保部csh、