某省電信匯聚交換機OLT雙上行配置模板

1、匯聚交換機olt雙上行配置模板v2華為s8505模式一：單鏈路+smar-link1. 板卡硬件要求：要求板卡中帶有“db”字樣并且軟件版本在1267以上、或者沒有“db”字樣軟件版本在1628以上，可以支持靈活qinq 。2. 軟件版本要求：release1600以上可以配smart-link3. 配置命令 定義vlan acl acl number 4001 rule 0 permit ingress 51 to 1050 egress any /匹配普通寬帶撥號用戶vlan rule 1 permit ingress 43 egress any /匹配itv用戶vlan rule 2 p

2、ermit ingress 45 egress any /匹配itms終端管理vlan 定義外層vlanvlan 501-502 901-902 1701-1702 smart-link配置stp region-configuration instance 1 vlan 501 901 1701instance 2 vlan 502 902 1702active region-configuration /每次更改配置后必須執行這條命令才生效smart-link group 1 preemption mode role /啟用故障鏈路恢復后的自動倒換功能 protected-instance

3、1 undo flush enablesmart-link group 2 preemption mode role /啟用故障鏈路恢復后的自動倒換功能 protected-instance 2 undo flush enableinterface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50為dslam管理vlan port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 vlan filter di

4、sable traffic-redirect inbound link-group 4001 rule 0 system-index 1 nested-vlan 501 traffic-redirect inbound link-group 4001 rule 1 system-index 2 nested-vlan 1701 traffic-redirect inbound link-group 4001 rule 2 system-index 3 nested-vlan 901/system-index一般按順序排列，只要不重復即可。interface gigabitethernetx/x

5、/x /下行接口2 port link-type hybrid port hybrid vlan 50 tagged port hybrid vlan 502 902 1702 untagged undo port hybrid vlan 1 vlan filter disable traffic-redirect inbound link-group 4001 rule 0 system-index 4 nested-vlan 502 traffic-redirect inbound link-group 4001 rule 1 system-index 5 nested-vlan 1702

6、 traffic-redirect inbound link-group 4001 rule 2 system-index 6 nested-vlan 902interface gigabitethernetx/x/x-01 /端口做為instance 1主用，instance 2備用port link-type trunk port trunk permit vlan 48 50 501-502 901-902 1701-1702 port smart-link group 1 masterport smart-link group 2 slaveinterface gigabitether

7、netx/x/x-02 /端口做為instance 1備用，instance 2主用port link-type trunk port trunk permit vlan 49 501-502 901-902 1701-1702 port smart-link group 1 slave port smart-link group 2 master 雙網管地址配置interface vlan 48 ip address a.b.c.2 255.255.255.252interface vlan 49 ip address a.b.c.6 255.255.255.252ip route 0.0.

8、0.0 0.0.0.0 a.b.c.1ip route 10.10.0.0.255.255.0.0 a.b.c.5 /10.10.0.0為網絡管理服務器段4. 業務調試驗證命令display smart-link group 1模式二：鏈路捆綁+smart-link1. 板卡硬件要求：要求板卡中帶有“db”字樣并且軟件版本在1267以上、或者沒有“db”字樣軟件版本在1628以上，可以支持靈活qinq 。2. 軟件版本要求：release1600以上可以配smart-link3. 配置命令 定義vlan acl acl number 4001 rule 0 permit ingress 51

9、to 1050 egress any rule 1 permit ingress 43 egress any rule 2 permit ingress 45 egress any 定義外層vlanvlan 501 1701 901 定義鏈路組link-aggregation group 1 mode manuallink-aggregation group 2 mode manual smart-link配置stp region-configuration instance 1 vlan 501 901 1701active region-configuration /每次更改配置后必須執行

10、這條命令才生效smart-link group 1 preemption mode role /啟用故障鏈路恢復后的自動倒換功能 protected-instance 1link-aggregation group 1 master /鏈路組1作為master link-aggregation group 2 slave /鏈路組2作為slaveundo flush enableinterface gigabitethernetx/x/x /下行接口 port link-type hybrid port hybrid vlan 50 tagged port hybrid vlan 501 90

11、1 1701 untagged undo port hybrid vlan 1 vlan filter disable traffic-redirect inbound link-group 4001 rule 0 system-index 1 nested-vlan 501 traffic-redirect inbound link-group 4001 rule 1 system-index 2 nested-vlan 1701 traffic-redirect inbound link-group 4001 rule 2 system-index 3 nested-vlan 901/sy

12、stem-index一般按順序排列，只要不重復即可。interface gigabitethernetx/x/x-01 /主用上行口-1port link-type trunk port trunk permit vlan 48 50 501 901 1701 port link-aggregation group 1 /把端口加入link-aggregation group 1interface gigabitethernetx/x/x-02 /主用上行口-2port link-type trunk port trunk permit vlan 48 50 501 901 1701 port

13、 link-aggregation group 1 /把端口加入link-aggregation group 1interface gigabitethernetx/x/x-03 /備用上行口-1port link-type trunk port trunk permit vlan 49-50 501 901 1701 port link-aggregation group 2 /把端口加入link-aggregation group 2interface gigabitethernetx/x/x-04 /備用上行口-2port link-type trunk port trunk permi

14、t vlan 49-50 501 901 1701 port link-aggregation group 2 /把端口加入link-aggregation group 2 雙網管地址配置interface vlan 48 ip address a.b.c.2 255.255.255.252interface vlan 49 ip address a.b.c.6 255.255.255.252ip route 0.0.0.0 0.0.0.0 a.b.c.1ip route 10.10.0.0.255.255.0.0 a.b.c.5 /10.10.0.0為網絡管理服務器段4. 業務調試驗證命令d

15、isplay smart-link group 1display link-aggregation verbose模式三：單鏈路/鏈路捆綁+vlan雙向透傳1. 板卡硬件要求：要求板卡中帶有“db”字樣并且軟件版本在1267以上、或者沒有“db”字樣軟件版本在1628以上，可以支持靈活qinq。2. 軟件版本要求：無特殊要求3. 配置命令 定義vlan acl acl number 4001 rule 0 permit ingress 51 to 1050 egress any rule 1 permit ingress 43 egress any rule 2 permit ingress

16、45 egress any 定義外層vlanvlan 501 1701 901 vlan雙向透傳配置interface gigabitethernetx/x/x /下行接口 port link-type hybrid port hybrid vlan 50 tagged port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 vlan filter disable traffic-redirect inbound link-group 4001 rule 0 system-index 1 nested-vlan 501 tr

17、affic-redirect inbound link-group 4001 rule 1 system-index 2 nested-vlan 1701 traffic-redirect inbound link-group 4001 rule 2 system-index 3 nested-vlan 901/system-index一般按順序排列，只要不重復即可。interface gigabitethernetx/x/x-01 /上行口1port link-type trunk port trunk permit vlan 48 50 501 901 1701interface giga

18、bitethernetx/x/x-02 /上行口2port link-type trunk port trunk permit vlan 49 501 901 1701 雙網管地址配置interface vlan 48 ip address a.b.c.2 255.255.255.252interface vlan 49 ip address a.b.c.6 255.255.255.252ip route 0.0.0.0 0.0.0.0 a.b.c.1ip route 10.10.0.0.255.255.0.0 a.b.c.5 /10.10.0.0為網絡管理服務器段4. 業務調試驗證命令dis

19、play vlan x/x/x華為s9300模式一：單鏈路+smar-link 靈活qinq配置：（s9300主機版本為v100r001版本或業務單板類型最后一個字母為a的單板使用如下流策略配置靈活qinq）1、 定義內層vlan的流策略： traffic classifier qinqa-1if-match vlan-id 51 to 1050 /匹配普通寬帶撥號用戶vlantraffic classifier qinqa-2if-match vlan-id 43 /匹配itv用戶vlantraffic classifier qinqa-3if-match vlan-id 45 /匹配itm

20、s終端管理vlan#traffic behavior qinqa-1nest top-most vlan-id 501 /外層vlantraffic behavior qinqa-2nest top-most vlan-id 901 /外層vlantraffic behavior qinqa-3nest top-most vlan-id 1701 /外層vlan#traffic behavior qinqb-1nest top-most vlan-id 502 /外層vlantraffic behavior qinqb-2nest top-most vlan-id 902 /外層vlantra

21、ffic behavior qinqb-3nest top-most vlan-id 1702 /外層vlan#traffic policy qinqaclassifier qinqa-1 behavior qinqa-1classifier qinqa-2 behavior qinqa-2classifier qinqa-3 behavior qinqa-3traffic policy qinqbclassifier qinqa-1 behavior qinqb-1classifier qinqa-2 behavior qinqb-2classifier qinqa-3 behavior q

22、inqb-32、 定義外層vlanvlan batch 501 502 901 902 1701 17023、 接口配置interface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50為dslam管理vlan port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 traffic-policy qinqa inbound#interface gigabitethernetx/x/x /下行接口1 po

23、rt link-type hybrid port hybrid vlan 50 tagged /vlan 50為dslam管理vlan port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1 traffic-policy qinqb inbound# 靈活qinq配置：（s9300主機版本為v100r002版本或業務單板最后一個字母非a的單板使用如下stacking配置靈活qinq）1、 定義外層vlanvlan batch 501 502 901 902 1701 17022、接口配置interface gigabitet

24、hernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50為dslam管理vlan port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 port vlan-stacking vlan 51 to 1050 stack-vlan 501port vlan-stacking vlan 43 stack-vlan 901port vlan-stacking vlan 45 stack-vlan 1701#interface gigab

25、itethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50為dslam管理vlan port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1port vlan-stacking vlan 51 to 1050 stack-vlan 502port vlan-stacking vlan 43 stack-vlan 902port vlan-stacking vlan 45 stack-vlan 1702# smart-link配

26、置stp region-configuration instance 1 vlan 501 901 1701instance 2 vlan 502 902 1702active region-configuration /每次更改配置后必須執行這條命令才生效smart-link group 1protected-vlan reference-instance 1 restore enable /啟用故障鏈路恢復后的自動倒換功能 smart-link enable port gigabitethernet1/0/1 masterport gigabitethernet1/0/2 slave ti

27、mer wtr 30 /配置主端口恢復30s后恢復smart-link group 2protected-vlan reference-instance 1 restore enable /啟用故障鏈路恢復后的自動倒換功能 smart-link enable port gigabitethernet1/0/2 masterport gigabitethernet1/0/1 slavetimer wtr 30 /配置主端口恢復30s后恢復#interface gigabitethernet1/0/1 /端口做為instance 1主用，instance 2備用port link-type tru

28、nk port trunk permit vlan 48 50 501-502 901-902 1701-1702#interface gigabitethernet1/0/2 /端口做為instance 1備用，instance 2主用port link-type trunk port trunk permit vlan 49 501-502 901-902 1701-1702 雙網管地址配置interface vlan 48 ip address a.b.c.2 255.255.255.252interface vlan 49 ip address a.b.c.6 255.255.255.

29、252ip route 0.0.0.0 0.0.0.0 a.b.c.1ip route 10.10.0.0.255.255.0.0 a.b.c.5 /10.10.0.0為網絡管理服務器段 業務調試驗證命令display smart-link group 1模式二：鏈路捆綁+smart-link 靈活qinq配置：（s9300主機版本為v100r001版本或業務單板類型最后一個字母為a的單板使用如下流策略配置靈活qinq）1、 定義內層vlan的流策略： traffic classifier qinqa-1if-match vlan-id 51 to 1050 /匹配普通寬帶撥號用戶vlantr

30、affic classifier qinqa-2if-match vlan-id 43 /匹配itv用戶vlantraffic classifier qinqa-3if-match vlan-id 45 /匹配itms終端管理vlan#traffic behavior qinqa-1nest top-most vlan-id 501 /外層vlantraffic behavior qinqa-2nest top-most vlan-id 901 /外層vlantraffic behavior qinqa-3nest top-most vlan-id 1701 /外層vlan#traffic b

31、ehavior qinqb-1nest top-most vlan-id 502 /外層vlantraffic behavior qinqb-2nest top-most vlan-id 902 /外層vlantraffic behavior qinqb-3nest top-most vlan-id 1702 /外層vlan#traffic policy qinqaclassifier qinqa-1 behavior qinqa-1classifier qinqa-2 behavior qinqa-2classifier qinqa-3 behavior qinqa-3traffic pol

32、icy qinqbclassifier qinqa-1 behavior qinqb-1classifier qinqa-2 behavior qinqb-2classifier qinqa-3 behavior qinqb-32、 定義外層vlanvlan batch 501 502 901 902 1701 17023、 接口配置interface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50為dslam管理vlan port hybrid vlan 501 901

33、 1701 untagged undo port hybrid vlan 1 traffic-policy qinqa inbound#interface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50為dslam管理vlan port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1 traffic-policy qinqb inbound# 靈活qinq配置：（s9300主機版本為v100r002版本或

34、業務單板最后一個字母非a的單板使用如下stacking配置靈活qinq）1、 定義外層vlanvlan batch 501 502 901 902 1701 17022、接口配置interface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50為dslam管理vlan port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 port vlan-stacking vlan 51 to 1050 stack

35、-vlan 501port vlan-stacking vlan 43 stack-vlan 901port vlan-stacking vlan 45 stack-vlan 1701#interface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50為dslam管理vlan port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1port vlan-stacking vlan 51 to 1050 st

36、ack-vlan 502port vlan-stacking vlan 43 stack-vlan 902port vlan-stacking vlan 45 stack-vlan 1702# smart-link配置stp region-configuration instance 1 vlan 501 901 1701instance 2 vlan 502 902 1702active region-configuration /每次更改配置后必須執行這條命令才生效smart-link group 1protected-vlan reference-instance 1 restore e

37、nable /啟用故障鏈路恢復后的自動倒換功能 smart-link enable port eth-trunk1 masterport eth-trunk2 slave timer wtr 30 /配置主端口恢復30s后恢復smart-link group 2protected-vlan reference-instance 1 restore enable /啟用故障鏈路恢復后的自動倒換功能 smart-link enable port eth-trunk2 masterport eth-trunk1 slavetimer wtr 30 /配置主端口恢復30s后恢復#interface g

38、igabitethernetx/x/x-01 /主用上行口-1eth-trunk1 /把端口加入link-aggregation group 1interface gigabitethernetx/x/x-02 /主用上行口-2eth-trunk1 /把端口加入link-aggregation group 1interface gigabitethernetx/x/x-03 /備用上行口-1eth-trunk2 /把端口加入link-aggregation group 2interface gigabitethernetx/x/x-04 /備用上行口-2eth-trunk2 /把端口加入lin

39、k-aggregation group 2interface eth-trunk1 /端口做為instance 1主用，instance 2備用port link-type trunk port trunk permit vlan 48 50 501-502 901-902 1701-1702#interface eth-trunk2 /端口做為instance 1備用，instance 2主用port link-type trunk port trunk permit vlan 49 501-502 901-902 1701-1702 雙網管地址配置interface vlan 48 ip

40、address a.b.c.2 255.255.255.252interface vlan 49 ip address a.b.c.6 255.255.255.252ip route 0.0.0.0 0.0.0.0 a.b.c.1ip route 10.10.0.0.255.255.0.0 a.b.c.5 /10.10.0.0為網絡管理服務器段 業務調試驗證命令display smart-link group 1display link-aggregation verbose模式三：單鏈路/鏈路捆綁+vlan雙向透傳 靈活qinq配置：（s9300主機版本為v100r001版本或業務單板類型最

41、后一個字母為a的單板使用如下流策略配置靈活qinq）1、 定義內層vlan的流策略： traffic classifier qinqa-1if-match vlan-id 51 to 1050 /匹配普通寬帶撥號用戶vlantraffic classifier qinqa-2if-match vlan-id 43 /匹配itv用戶vlantraffic classifier qinqa-3if-match vlan-id 45 /匹配itms終端管理vlan#traffic behavior qinqa-1nest top-most vlan-id 501 /外層vlantraffic beh

42、avior qinqa-2nest top-most vlan-id 901 /外層vlantraffic behavior qinqa-3nest top-most vlan-id 1701 /外層vlan#traffic behavior qinqb-1nest top-most vlan-id 502 /外層vlantraffic behavior qinqb-2nest top-most vlan-id 902 /外層vlantraffic behavior qinqb-3nest top-most vlan-id 1702 /外層vlan#traffic policy qinqacl

43、assifier qinqa-1 behavior qinqa-1classifier qinqa-2 behavior qinqa-2classifier qinqa-3 behavior qinqa-3traffic policy qinqbclassifier qinqa-1 behavior qinqb-1classifier qinqa-2 behavior qinqb-2classifier qinqa-3 behavior qinqb-32、 定義外層vlanvlan batch 501 502 901 902 1701 17023、 接口配置interface gigabite

44、thernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50為dslam管理vlan port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 traffic-policy qinqa inbound#interface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50為dslam管理vlan port hybri

45、d vlan 502 90121702 untagged undo port hybrid vlan 1 traffic-policy qinqb inbound# 靈活qinq配置：（s9300主機版本為v100r002版本或業務單板最后一個字母非a的單板使用如下stacking配置靈活qinq）1、定義外層vlanvlan batch 501 502 901 902 1701 17022、接口配置interface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 50為ds

46、lam管理vlan port hybrid vlan 501 901 1701 untagged undo port hybrid vlan 1 port vlan-stacking vlan 51 to 1050 stack-vlan 501port vlan-stacking vlan 43 stack-vlan 901port vlan-stacking vlan 45 stack-vlan 1701#interface gigabitethernetx/x/x /下行接口1 port link-type hybrid port hybrid vlan 50 tagged /vlan 5

47、0為dslam管理vlan port hybrid vlan 502 90121702 untagged undo port hybrid vlan 1port vlan-stacking vlan 51 to 1050 stack-vlan 502port vlan-stacking vlan 43 stack-vlan 902port vlan-stacking vlan 45 stack-vlan 1702#interface gigabitethernetx/x/x-01 /上行口1port link-type trunk port trunk permit vlan 48 50 50

48、1 901 1701interface gigabitethernetx/x/x-02 /上行口2port link-type trunk port trunk permit vlan 49 501 901 1701 雙網管地址配置interface vlan 48 ip address a.b.c.2 255.255.255.252interface vlan 49 ip address a.b.c.6 255.255.255.252ip route 0.0.0.0 0.0.0.0 a.b.c.1ip route 10.10.0.0.255.255.0.0 a.b.c.5 /10.10.0.

49、0為網絡管理服務器段 業務調試驗證命令display vlan x/x/x中興t64g模式一：單鏈路+zess-link1. 板卡硬件要求：每臺t64g至少配置1塊ugsf板卡2. 軟件版本要求：v2.8.01b19或v2.8.01c20以上3. 配置命令 全局配置stpspanning-tree enable /全局配置為stp enable，所有端口配置為stp disablespanning-tree mst configurationinstance 1 vlan 501,1701.901instance 2 vlan 502,1702.902 端口配置interface gei_1/

50、1 /下行customer-port配置 switchport mode hybrid switchport hybrid native vlan 501 /見注意事項1 switchport hybrid vlan 50 tag switchport hybrid vlan 901 untag switchport hybrid vlan 1701 untag switchport qinq customer /定義端口為c口spanning-tree disable /關閉stpinterface gei_1/2 /下行customer-port配置 switchport mode hyb

51、rid switchport hybrid native vlan 502 /見注意事項1 switchport hybrid vlan 50 tag switchport hybrid vlan 902 untag switchport hybrid vlan 1702 untag switchport qinq customer /定義端口為c口 spanning-tree disable /關閉stpinterface gei_1/24 /上行uplink-port配置 switchport mode hybridswitchport hybrid native vlan 48switc

52、hport hybrid vlan 48 tag switchport hybrid vlan 50 tag switchport hybrid vlan 501-502 tag switchport hybrid vlan 1701-1702 tagswitchport hybrid vlan 901-902 tag switchport hybrid vlan 2 untag switchport qinq uplink /定義端口為u口spanning-tree disable /關閉stpinterface gei_2/24 /上行uplink-port配置 switchport mode hybridswitchport hybrid native vlan 49 switchport hybrid vlan 49 tag switchport hybrid vlan 501-502 tag switchport hybrid vlan 1701-1702 tagswitchport hybrid vlan 901-902 tag switchport qinq uplink /定義端口為u口spanning-tree disable /關閉stp session設置vlan qinq sessi