射流混漿器說明書

1、JSL150射流混漿器使用說明書鄭州金時機械有限公司（使用設備前請仔細閱讀該手冊）目 錄一、用途及結構組成二、工作原理三、主要參數四、安裝調試五、設備維護如果您在使用中有什么疑問，或遇到了什么問題請及時與我們聯系，我們將熱情為您服務。地址(Addr)：鄭州市二七區馬寨鎮明暉路6號。No.6, MingHui Road, Mazhai town, Erqi district ,Zhengzhou ,Henan電話(Tel)傳真 (Fax)：+86-371-86156588郵編(Post code)：450003 E-mail：fieldtian327 網址(Web si

2、te)：一、用途及結構組成鉆井液射流混合漏斗是鉆井液固控系統的重要組成部分，是最常用的一種配液裝置。在發生井噴的緊急情況下，可以利用鉆井液射流混合漏斗在最短的時間內，均勻的混合大量的加重材料。射流混合漏斗的結構原理簡圖：1、加料漏斗 2、濾網 3、蝶閥 4、射流泵總成 5、底座二、工作原理鉆井液以一定壓力進入射流泵，在射流泵內，液體由噴咀噴出后，經混合室，進入剪切管，物料由漏斗加入混合室，在噴咀噴出的液流帶動下進入剪切管，并在此過程中得到分散和混合，混合后的液體流出剪切管后進入鉆井液罐。剪切管是一根按一定曲面逐漸擴張的空心管，它的主要作用是增加液體在管內的剪切力，以便物料更好地進行分散和提高混

3、合后液體的壓力，以便進入循環罐。剪切管實際上利用了“流得快，壓力低；流得慢，壓力高 ”的伯努利效應?；旌鲜覂?nèi)由于液體從噴咀以高速噴出，此時壓力低；液體進入剪切管后，由于截面逐漸變大，速度變小，于是壓力升高。三、主要參數配漿能力： 200 m3/h 進口壓力：0.250.6MPa出口壓力： 0.10.3MPa 進出口尺寸： 6×6重量： 205kg外形尺寸： 1373×750×970mm（L×W×H）四、安裝調試1、鉆井液射流混合漏斗進口與砂泵的出口管線連接，出口進入鉆井液罐。2、進、出口均用6法蘭連接。3、射流混漿漏斗的底板固定要牢固。 4、射

4、流混合漏斗安裝不能過高，安裝的越高，混合能力越低。5、配用砂泵的技術性能要與射流混合漏斗相匹配。安裝尺寸圖如下：五、設備維護必要的日常維護不僅能提高設備運行的可靠性還可延長設備的使用壽命。1、日常維護日常維護工作主要是清理加料漏斗及混合室的異物，保持設備整潔。2、定期維護（1）連接緊固件為保證設備的正常運行，對各連接的緊固件定期檢查，一般每月檢查一次。（2）部件防腐及時為油漆破損處補防腐漆。 JSL-150 Jet mixerOperation ManualZHENGZHOU JINSHI MACHINERY CO.，LTD（PLEASE READ THE MANUAL CAREFULLY B

5、EFORE USE）ContentsI Applicability and StructureII Working MechanismIII Main ParametersIV Installation and CommissioningV MaintenanceIf you have any questions or problems,please contact us,we shall serve for you enthusiastically! 地址(Addr)：鄭州市二七區馬寨鎮明暉路6號。No.6, MingHui Road, Mazhai town, Erqi district

6、,Zhengzhou ,Henan電話(Tel)傳真 (Fax)：+86-371-86156588郵編(Post code)：450003 E-mail：fieldtian327 網址(Web site)：I. Applicability and StructureDrilling fluid jet mixer, an commonly used equipment in mixing fluid,is an important part of drilling fluid solid control system.When well blowout occurs,

7、it can be used to mix large amount of weighted materials even in drilling fluid within little time.Structural sketch:1. Feeding hopper 2. Strainer 3. Butterfly valve 4. Jet pump assy. 5. BaseII. Working MechanismThe drilling fluid flow into the jet pump with certain pressure,in the jet pump fluid sp

8、outs out from jet nozzle first, then flows into shear pipe through mixing chamber. Materials will be added from hopper to mixing hopper, and move into shear pipe with the flow. During this process, they are dispersed and mixed. The mixture will enter into drilling fluid tank when flows out of the sh

9、ear pipe.The shear pipe is hollow and it can expand gradually based on certain curved surface. It is mainly used to enlarge shearing force inside the pipe to disperse the material further and increase the mixture pressure head, this will make it easy to enter into circulating tank.Bernoulli effect i

10、s adopted in shear pipe which is flow rate is rapid with low pressure, and slow with high pressure. Pressure is low in the chamber when fluid spouts out in high speed from the jet nozzle; when fluid enters into the shear pipe, its section is enlarged and flow rate decreased so the pressure rises.III

11、 Main ParametersFluid mixing capacity: 200 m3/h Inlet pressure: 0.250.6MPaOutlet pressure: 0.10.3MPa Inlet and outlet size: 6×6Weight: 205kgSize: 1373mm×750mm×970mmIV Installation and Commissioning1. Connect the inlet opening of drilling fluid mixing jet mixer with the outlet pipe of

12、sand pump, and the jopper outlet leads to drilling mud tank.2. 6flanges should be used at inlet and outlet.3. Base plate of the hopper should be fixed tightly.4. The hopper should not be equipped too high, since the more high, the less of mixing capacity.5. The sand pump used here should match with

13、the mixing jet mixer.The following is the installation dwg.V MaintenanceThe necessary maintenance can improve the working reliability of the mixer,and can prolong its service life.1. daily maintenanceThe work is cleaning the feeding hopper and mixing chamber,keeping the equipment neat.2. Periodic maintenance（1）checking the fastenersChecking the fasteners once a month,be sure they are tightening.（2）unit anticorrosionPainting the paint breakage timely.鄭州金時機械有限公司ZHENGZHOU JINSHI MACHINERY CO.,LTD誠信為本 技術為先Good faith-based Technology