交工文件201-213試驗記錄報告表

1、.天俱時時工程科技集團有限公司基礎沉降測量記錄Foudation settlement surveying records項 目: Project裝 置: Unit工 號: Section位 號Location No.名 稱Name參考水準點Reference bench mark標 高E;evation測量點位置Location of surveying安裝前Before erection安裝后After erection加負荷Loading負荷后After Loading日期Date標 高Elevation日期Date標 高Elevation負荷量Load日期Date標 高Elevatio

2、n日期Date標 高Elevation 測量草圖:Surveying sketch技術負責人Technical person in charge測量人Surveyor表201天俱時工程科技有限公司機 泵安裝工序質量控制表Qualily control table for machine and pump installing procedures項 目:伊犁川寧生物技術有限公司一期抗生素中間體項目安裝工程Project裝 置:提取一車間Unit工 號:Section位 號Location No.P21702D名 稱Name 陶瓷膜批次過濾循環泵工作介質Medium工藝液體驅動機類型Type o

3、f driver傳動方式Transmission mode聯軸器執行標準Standard for execution檢 查 項 目Inspection item等 級Grade簽名/日期Signature/date施工單位Subcontractor監理單位建設單位Owner機器及附件接收Acceptance of machine and accessoriesC基礎復查Check of foundationC機泵安裝Installation of machine and pumpCR灌漿前檢查Inspection before groutingAR拆洗及回裝Disassembling clea

4、ning and reassemblingC(CR)聯軸節對中Centering of couplersA傳動裝置檢查Transmission gearC潤滑油系統檢查、注油Lubrication system inspection and oilingC冷卻、密封系統檢查Cooling and sealing systemC試運轉Test run AR找 正 偏 差Alignment deviation對 中 偏 差Centering deviation位置Location 允差Tolerance0°180°90°270°配管前Before pipe

5、assembling配管后After pipe assembling水平Horizontal0.10.20.040.04位置Location 允差Tolerancea1a2a3a4a1a2a3a4中心Center徑向Radial標高Elevation軸向Axial從驅動機方向讀數Reading in direction of driver百分表固定端：Fixed end of dial indicator聯軸器間距：mmSpacing of couplers試運轉Test temp介質：潔凈水Medium持續時間：Time durationa=tg=a1a2a3a1a4機器軸承溫度Machin

6、e Bearing Temp.前： Front后： Rear驅動機軸承溫度Driver bearing temp前： Front后： Rear壓力Pressure進： MPaIn出： MPaOut機溫升 Motor temp.rise電流（啟動/運轉） ACurrent(starting /running)備 注：Remarks表202機 組安裝工序質量控制表Quality control table for machineSet installing procedures項 目:Project裝 置:Unit工 號:Section位 號Location No.名稱Name執行標準Standa

7、rd for execution驅動機Driver主 機Host machine種 類Type型 號Model種 類Type型 號Model功 率Power轉 速Rotating speed r/min介 質Medium檢 查 項 目Inspection item等 級Grade簽名/日期Signature/date施工單位Subcontractor監理單位Contractor建設單位Owner機組及附件接收Acceptance of machine setaccessoriesC基礎復查check of foundationC機組安裝Installation of machine setA灌

8、漿前檢查Inspection before groutingAR聯軸節對中Centering of couplerAR機組安裝完整性確認Integrity of machine set installationB機組拆檢組裝情況Disassembling,inspecting and assm-bling of machine setCR油系統沖洗Flushing of oil systemA油系統整定Setting of oil systemB冷卻系統Cooling systemC冷凝真空系統Condensing vacuum systemB控制和保護系統Control and protec

9、tion systemB盤車裝置檢查Idle rotating deviceC試運轉Test runAR部 位Location油標號Mark of oil合格證號Certificate No.注油數量Oiling quantity簽名/日期Signature/date備注：Remarks表203機組安裝找正記錄Alignment record for installation of machine set項 目:Project裝 置:Unit工 號:Section位 號Location No.名 稱Name執行標準Standard for execution項 目Item允許偏差(mm)Tol

10、erance實 際 偏 差 (mm)Actual deviation 標 高 Elevation中心線Centerline 縱 向 Longitudinal 橫 向 Transverse 水平測量 (mm/m) Levelling12345678910縱 向Longitudinal允許值Allowable value實測值Measured value橫 向Transverse允許值Allowable value實測值Measured value 附 圖: Attached diagram監理單位代表施工單位Subcontractor施工人Operator建設單位代表Owner represen

11、tative檢查員Inspector表204大型機械灌漿前檢查記錄Inspection record before grouting of large machinery項 目:Project裝 置:Unit工 號:Section位 號Location No.名 稱Name執行標準Standard for execution 隱蔽前檢查: Inspection before concealing 1.墊鐵: 布置 接觸面 焊接 Shims Layout Contact face Welding 2.地腳螺栓 3.螺栓孔及基礎表面清潔 Anchoring bolt Bolt hole and f

12、oundation surface cleanliness 4.墊鐵規格: 平墊鐵_ 斜墊鐵_ Specification of shims Flat shims Tapered shims附圖:Attached diagram No. h×nLNo.h×nLNo.h×nL 施工人: Operator上項工程經檢查符合設計(規范)要求,可以隱蔽。The above work conforming to the requirement of design(code)may be concealed 年 月 日 Date建設單位代表Owner representati

13、ve監理單位代表施工單位表205機器拆檢及組裝間隙測量記錄Clearance measurement record for disass-embling, Inspecting and assembling of machine項 目:Project裝 置:Unit工 號:Section位 號Location No.名 稱Name執行標準Standard for execution間隙測量部位Clearance measured location規定值（mm）Specified value拆前間隙（mm）Clearance before disassembling組裝后間隙（mm）Cleara

14、nce afterassembling日 期Date注：間隙測量部位另附圖 （如果需要）。Note: Clearance measured location has diagram attached(if necessary).檢查員Inspector施工人Operator表206電機空氣間隙測量記錄Air gap measurement record for motor項 目:Project裝 置:Unit工 號:Section位 號Location No.名稱Name執行標準Standard for execution按定子上標定的一點盤車檢查空氣間隙 單位：（mm）Inspection

15、of air gap at specified point on the stator by idle rotating Unit:部位Location12345678910 111213141516171819實測值Measured value按轉子上標定的一點盤車檢查空氣間隙 單位：(mm)Inspection of air gap at specified point on the rotor by idle rotating Unit:部位Location12345678910實測值Measured value監理單位檢查員Inspector施工人Operator表128機組對中記錄A

16、lignment record of machine set項 目:Project裝 置:Unit工 號:Section位 號Location No.名稱Name執行標準Standard for execution允許偏差允許偏差聯軸器編號Coupler No.徑 向Radial軸 向Axial端面間隙Clearance at end百分表固定位置Fixed position of dial indicatorTolerancea1a2a3a4 Tolerance b1b2b3b4規定值Stipulated value實測值Measured value 備注：Remarks監理單位代表施工單位

17、Sub-contractor施工人Operator建設單位代表Owner representative檢查員Inspector表208_透平運轉報告 Test-run report for_ turbine項 目:Project裝 置:Unit工 號:Section位 號Location No.機組名稱Name of machine set功 率Power介質名稱Name of medium介質壓力Pressure of mediumMpa介質溫度Temp. Of medium額定轉速Rated rota-tional speedr/min試車類別Type of test run試車日期Dat

18、e of test run執行標準Standard for execution危急保安器試驗Test of emergency protection device手動Manual自動Automatic時 間轉 速軸振動（mm）軸位移 （mm）備 注TimeSpeed介 質Medium潤滑油Lubricant軸承溫度Bearing temp()Shaft vibrationShaft displacement Remarks流量Flow rate溫度Temp()壓力Pressure(Mpa)溫度Temp()壓力Pressure(Mpa)前Front后Rear進In出out 進In出out 進In

19、 出out 進In出out 試運轉結果Result of test run監理單位代表施 工 單 位Subcontractor 施工人Operator建設單位代表Owner representative檢查員Inspector209機器試運轉報告Test run report of machine項 目:Project裝 置:Unit工 號:Section位 號Location No.機組名稱Name of machine set功 率Power試車類別Type of test run日 期Date執行標準Standard for execution(r/min) 轉 速時 間軸振動（mm）軸

20、位移 （mm）備 注Time Speed介 質Medium潤滑油Lubricant軸承溫度Bearing temp()Shaft vibrationShaft displacement Remarks流量Flow rate溫度Temp()壓力Pressure(Mpa)溫度Temp()壓力Pressure(MPa)前Front后Rear進In出out 進In出out 進In 出out 進In出out 試運轉結果Result of test run監理單位代表施 工 單 位Subcontractor 施工人Operator建設單位代表Owner representative檢查員Inspector

21、表210大型軸流風機安裝工序質量控制表Quality control table for installing procedures of large axial flow blower項 目:Project裝 置:Unit工 號:Section位 號 Location No. 傳動方式Mode of transmission名 稱Name執行標準Standard for execution檢 查 項 目Inspection item等級Grade簽 名Signature施工單位Subcontractor監理單位建設單位Owner機器及附件接收Acceptance of machine and

22、 accessoriesC基礎復查Check of foundationC機器安裝Installation of machineCR驅動機對中Alignment of driverC灌漿前檢查Inspection before groutingA風筒安裝Installation of wind ductC傳動裝置檢查Transmission gearC翼片安裝Fitting of bladeCR潤滑部位檢查、注油Lubrication system inspection and oilingC電機轉向檢查Rotating direction of motorC試 運 轉 Test run持續時

23、間Duration hAR電機軸承溫度Motor bearing temp. 風機軸承溫度Blower bearing temp. 電機定子溫升Motor stator temp.rise 結 果Result找 正 偏 差Alignment deviation翼 片 安 裝Fitting of blade允 差Tolerance0°180°90°180°垂直度(mm/m）Verticality翼片角度偏差Blade angle deviation1234中心（mm）Center標高（mm）Elevation翼片間隙 （mm） Clearance at b

24、lade tip 最 大Max.最 小Min.附注：Note:表211立式攪拌器安裝工序質量控制表Quality control table for installing procedures of vertical agitator項 目:Project裝 置:Unit工 號:Section位 號Location No. 名 稱Name工作介質Medium執行標準Standard for execution檢 查 項 目Inspection item等級Grade簽 名/日 期Signature/date施工單位Subcontractor監理單位建設單位Owner機器及附件接收Accepta

25、nce of machine and accessoriesC支架（支架法蘭）安裝Installation of supportC容器與攪拌器法蘭墊片安裝Setting flange gaskets of vessel and agitatorC找正AlignmentBR皮帶輪平行度確認Parallelism of belt pulleyC齒輪箱內部清潔度確認Cleanliness in gear boxC注油（脂）Oiling(greasing)C冷卻、密封系統檢查Cooling and sealing systemC電機轉向檢查Rotating direction of motorC試 運

26、 轉 Test runAR ba找正記錄Alignment recordammbmm垂直度Verticalitymm/m備注：Remarks表212空 調 系 統安裝工序質量控制表Quality control table for installing air conditioner system項 目:Project裝 置:Unit工 號:Section位 號Location No.型 號Model制造廠Manufacturer制冷量Refrigerationoutput制冷劑Refrigerant執行標準Standard for execution檢 查 項 目Inspection ite

27、m等級Grade簽 名/日 期Signature/date施工單位Subcontractor監理單位r建設單位Owner機械及附件接收Acceptance of machine accessoriesC基礎及預留孔道復查Check of foundation provided holesC主機及附件安裝Installation of host machine accessoriesC內部清潔度確認Interior cleanlinessB機器拆卸、清洗Disassembling cleaning of machineB氣密性試驗Air-tightness testB充填制冷劑Filling refrigerantA制冷劑系統檢漏Leakage check of refrigerant systemA風管及部件制作安裝Cleaning of vent duct interiorC風管內部清理Cleaning of vent duct interior冷卻水管道安裝Installation of cooling water pipelineC試 運 轉 Test runAR附注：Remarks表213輸 送 機 械安裝工序質量控制表Quality control table for installing procedures of conveying machine項 目:P