LTE的多址接入技術-外文翻譯

1、LTE的多址接入技術LTE的多址接入OFDM傳輸正交頻分復用（OFDM）是一種多載波傳輸技術，已被采納為3gpplong長期演化（LTE）的下行鏈路傳輸方案，也可用于其他幾個無線技術，例如：wimax和DVB廣播技術。它的特點是在一個頻域內分布著許多帶有間隔的子載波 f=1/Tu其中， Tu是每個子載波的調制符號時間。如圖2-1所示，“OFDM子載波間隔 ”。OFDM的傳輸是基于塊的。每個OFDM符號間隔之間，調制符號是并行發送的。調制符號可以通過調制字母表得到，如QPSK，16QAM或64QAM，對于3GPP組織LTE，子載波間隔是相等的為15 kHz。另一方面，子載波的數目取決于傳輸帶寬，

2、在一個10MHZ的頻譜分配下，600個子載波可以有序傳輸。當然，帶寬減小了，子載波數目也相應減少，帶寬增加了，子載波數目也相應增加。圖2-1 OFDM子載波間隔在OFDM傳輸時，物理資源經常被描述成一個時域頻域的網格坐標圖。在這個坐標圖里一列對應一個OFDM子載波，一行對應一個OFDM子載波。如圖2-2所示，“OFDM時頻網格” 。盡管子載波的頻譜有重疊，但在理想情況下，是對OFDM子載波解調后不引起任何干擾的，這是因?yàn)閷?duì)每一個子載波間隔的特殊選擇，讓它等于相應的解調符號率。圖2-2 OFDM時頻網格以一定的頻率fs= N ×f進行采樣的OFDM信號，是該size-N的逆離

3、散傅立葉變換（IDFT）的調制符號塊a0, a1,.aN-1。因此，OFDM調制可以通過IDFT處理再到數字-模擬的轉換來實現。（見圖2-3，“OFDM調制”）。在實際中，OFDM調制是以快速傅立葉反變換（IFFT）方式實現簡單和快速的處理，通過選擇IDFT size N 等于2m（m為整數）。在接收端，對接收信號以fs= N ×f的頻率采樣，高效的FFT處理是用來實現OFDM的解調和檢索調制符號塊a0, a1,.aN-1。（參見圖2-4，“OFDM解調”）。圖2-3 OFDM調制圖2-4 OFDM解調正如上面提到的，一個無干擾的OFDM信號可以解調出無任何子載波

4、間干擾的信號。然而，在一個時間色散信道的情況下（如多徑無線信道），子載波之間的正交性丟失，造成符號間干擾（ISI）。這是因?yàn)椋庹{(diào)器相關區間的一條路徑將與不同路徑的符號邊界有重疊。（見圖2-5，“時間的分散性和相應的接收信號”）。圖2-5 次分散和相應的接收信號要解決這個問題，使OFDM信號在無線信道傳播時對時間色散完全不敏感，所謂的插入循環前綴通常被使用。如圖2-6所示，“插入循環前綴”。循環前綴插入就意味著OFDM符號的最后部分（第N個cp）被復制并且被插入到OFDM塊的開始部分。因此，OFDM符號的長度從TU 到TU +TCP ,其中TCP =NCPTU是循環前綴的長度。作為一個結果，O

5、FDM符號率是減少的。因此，在時間色散信道里，只要時間色散的跨度小于循環前綴的長度，子載波的正交性就能被保持。圖2-6插入循環前綴循環前綴插入的缺點是，在整個信號帶寬沒有減少，OFDM符號率減少的情況下，就意味著在吞吐量方面有相應的損失。OFDM調制組合（IFFT處理），一個（分散的）無線信道，以及解調（FFT處理）可以被看作是一個頻域信道。如圖2-7，“頻域模型的OFDM傳輸接收”，其中每個OFDM符號的時間期間，N個不同的調制碼元被發送，每一個在相應的子載波上，在對比單一寬帶載波系統時，如WCDMAwhere，每個調制符號被傳輸在整個帶寬上。圖2-7頻率的OFDM傳輸接收域模型在頻道k上，

6、調制符號ak被縮放和相位轉移，通過復雜的信道系數Hk（頻域）。在接收端，解調后允許發送的信息準確解碼。在接收端需要一個頻域的信道抽頭估計H0，H1， .， HN-1。這可以通過在OFDM時頻網格內以一定規律的間隔插入已知參考符號來實現，有時也稱作導頻符號或?qū)ьl器。運用參考符號的相關知識，接收機可以估計信道抽頭（頻域）用于解碼的必要。OFDM信號帶寬一個OFDM信號的帶寬等于N×f ，這就是說：子載波數乘以子載波間隔數。另一方面，通過設置這個傳輸符號從一側組相鄰子載波到零，這個基帶被減少到NC×f,其中NC 是非空子載波數目。然而，OFDM信號的頻譜脫落到基本帶寬以外的速度是

7、很慢的，尤其比一個WCDMA信號慢的多。因此，在實際中，一個OFDM需要10%的保護間隔。這也就是說，舉個例子，在一個 5 MHZ 的頻譜分配中，OFDM基本帶寬 NC ×f 大約是4.5 MHZ。做一個假設，例如，為L(zhǎng)TE選擇一個15 KHZ的子載波間隔，那么，在 5MHZ內應對應于300個子載波。DFT OFDM傳輸離散的傅里葉變換擴展的正交頻分復用（DFTS-OFDM）已被用作LTE上行鏈路的傳輸方案。DFTS-OFDM傳輸?shù)幕驹碓趫D2-8，“DFT的OFDM信號生成”中說明。類似于OFDM調制，DFTS-OFDM依賴于基于塊的信號生成。在DFTS-OFDM中，一個M調制符

8、號塊來自于一些調制字母表，比如，QPSK 或者 16QAM,第一次被應用到size-m DTF。這個DFT輸出被應用到一個size-N 的逆DFT的連續輸入當中。其中，N > M 且未使用的輸入（N-M）設置為零。和OFDM一樣，每個傳輸塊插入一個循環前綴。圖2-8 DFT的OFDM信號的產生與圖2-8，“DFT的OFDM信號生成”相比，基于IFFT OFDM調制的實現，很顯然，DFTS-OFDM可以看作是OFDM調制之前的DFT運算。如果DFT的M的大小等于IDFT的N的大小，那么級聯DFT和IDFT的塊圖2-8“DFT的OFDM信號生成”將完全抵消。如果M小于N且IDFT的

9、剩余輸入被設置為零，則IDFT的輸出將是一個低功率變化的信號，類似于一個單載波信號。此外，不同塊大小為m的瞬時帶寬發送的信號可以是多種多樣的，允許靈活的帶寬分配。與DFTS-OFDM的主要好處想比，多載波傳輸方案，如OFDM,減少變化的瞬時發射功率，對提高功率放大器效率是可能的。功率的變化一般根據測得的峰值平均功率比（PRPA）來判斷。定義為在峰值功率一個OFDM符號的平均信號功率的歸一化。對于DFTS-OFDM,PRPA明顯降低，相比OFDM,再考慮到移動終端的電源能力，這種傳輸技術在上行鏈路的傳輸中是非常有用的。DFTS-OFDM信號解調的基本原理如圖2-9所示，“DFT的OFDM解調”。

10、這些操作和圖2-9“DFT的OFDM解調”基本上是相反的。即size-n離散傅里葉變換處理中，和接受信號不對應的頻率采樣會被移除。圖2-9 DFTS OFDM調制LTE multiple access techniquesLTE multiple accessOFDM transmissionOrthogonal Frequency Division Multiplexing (OFDM) is a multicarrier transmissiontechnique that has been adopted as the downlink transmission scheme for t

11、he 3GPPLong-Term Evolution (LTE) and is also used for several other radio technologies, e.g.WiMAX and the DVB broadcast technologies.It is characterized by a tight frequency-domain packing of the subcarriers with a subcarrier spacing f = 1/Tu, where Tu is the per-subcarrier modulation-symbol time. (

12、See Figure 2-1, “OFDM subcarrier spacing”) .OFDM transmission is block-based. During each OFDM symbol interval, modulationsymbols are transmitted in parallel. The modulation symbols can be from any modulation alphabet, such as QPSK, 16QAM, or 64QAM.For 3GPP LTE, the basic subcarrier spacing equals 1

13、5 kHz. On the other hand, thenumber of subcarriers depends on the transmission bandwidth, with in the order of 600 subcarriers in case of operation in a 10 MHz spectrum allocation and correspondingly fewer/more subcarriers in case of smaller/larger overall transmission bandwidths.Figure 2-1 OFDM sub

14、carrier spacingThe physical resource in case of OFDM transmission is often illustrated as atime-frequency grid where a column corresponds to one OFDM symbol (time) and a row corresponds to one OFDM subcarrier, as illustrated in (see Figure 2-2, “OFDM time-frequency grid” ).In the ideal case, despite

15、 the fact that the spectrum of neighbor subcarriers do overlap, the OFDM subcarriers do not cause any interference to each other after demodulation due to the specific choice of a subcarrier spacing f equal to the modulation symbol rate.Figure 2-2 OFDM time-frequency gridAn OFDM signal sampled at a

16、rate fs = N × f is the size-N Inverse Discrete FourierTransform (IDFT) of the block of modulation symbols a0, a1,.aN-1. Thus, OFDMmodulation can be implemented by means of IDFT processing followed bydigital-to-analog conversion (see Figure 2-3, “OFDM modulation”) . In practice,the OFDM modulati

17、on can be implemented by means of Inverse Fast Fourier Transform (IFFT) easy and fast processing, by selecting the IDFT size N equal to 2m for some integerm. At the receiver, by sampling the received signal at the rate fs = N× f, efficient FFT processing is used to achieve OFDM demodulation and

18、 retrieve the block of modulation symbols a0, a1,.aN-1( see Figure 2-4, “OFDM demodulation”) .Figure 2-3 OFDM modulationFigure 2-4 OFDM demodulationAs mentioned above, an uncorrupted OFDM signal can be demodulated without anyinterference between subcarriers. However, in case of a time-dispersive cha

19、nnel (such as multipath radio channels), the orthogonality between the subcarriers is lost, causing Inter Symbol Interference (ISI). The reason for this is that the demodulator correlation interval for one path will overlap with the symbol boundary of a different path (see Figure 2-5,“Time dispersio

20、n and corresponding received signal”) Figure 2-5 Time dispersion and corresponding received signalTo deal with this problem and make an OFDM signal truly insensitive to time dispersion on the radio channel, so-called Cyclic Prefix insertion is typically used in case of OFDM transmission. As illustra

21、ted in(see Figure 2-6, “Cyclic Prefix insertion”) , cyclic-prefix insertion implies that the last part of the OFDM symbol (the last Ncp symbols) is copied and inserted at the beginning of the OFDM block, increasing thus the length of the OFDM symbol from Tu to Tu + Tcp, where Tcp = Ncp,Tu is the len

22、gth of the cyclic prefix.The OFDM symbol rate as is reduced as a consequence. Thus, subcarrier orthogonality is preserved in case of a time-dispersive channel, as long as the span of the time dispersion is shorter than the cyclic-prefix length.Figure 2-6 Cyclic Prefix insertionThe drawback of cyclic

23、-prefix insertion is that it implies a corresponding loss in terms of throughput as the OFDM symbol rate is reduced without a corresponding reduction in the overall signal bandwidth.The combination of OFDM modulation (IFFT processing), a (time-dispersive) radiochannel, and OFDM demodulation (FFT pro

24、cessing) can then be seen as afrequency-domain channel as illustrated in(see Figure 2-7, “Frequency domain model of OFDM transmission reception”) , where during each OFDM symbol time period, N different modulation symbols are transmitted, each on a given subcarrier over the corresponding sub-band, i

25、n contrast to single wideband carrier systems, such as a WCDMA where each modulation symbol is transmitted over the entire bandwidth.Figure 2-7 Frequency domain model of OFDM transmission receptionOn frequency channel k, modulation symbol ak is scaled and phase rotated by thecomplex (frequency-domai

26、n) channel coefficient Hk. At the receiver side, to allow forproper decoding of the transmitted information after demodulation, the receiver needs an estimate of the frequency-domain channel taps H0, H1,.,HN-1. This can be done by inserting known reference symbols, sometimes also referred to as pilo

27、t symbols or pilots,at regular intervals within the OFDM time/frequency grid. Using knowledge about the reference symbols, the receiver can estimate the (frequency-domain) channel taps necessary for the decoding.OFDM signal bandwidthThe basic bandwidth of an OFDM signal equals N × f, i.e. the n

28、umber of subcarriersmultiplied by the subcarrier spacing. On the other hand, by setting the symbols to betransmitted on a group of side contiguous subcarriers to zero, the basic bandwidth isreduced to Nc × f where Nc is the number of non-null subcarriers. However, the spectrum of an OFDM signal

29、 falls off slowly outside the basic OFDM bandwidth and especially much slower than for a WCDMA signal. Thus, in practice, typically in the order of 10% MHz. Assuming, for example, a subcarrier spacing of 15 kHz as selected for LTE, this corresponds to 300 subcarriers in 5 MHz.DFTS OFDM transmissionD

30、iscrete Fourier Transform Spread OFDM (DFTS-OFDM) is a transmission scheme that has been selected as the uplink transmission scheme for LTE. The basic principle of DFTS-OFDM transmission is illustrated in(see Figure 2-8, “DFTS OFDM signal generation”) . Similar to OFDM modulation, DFTS-OFDM relies o

31、n block-based signal generation. In case of DFTS-OFDM, a block of M modulation symbols from some modulation alphabet, e.g. QPSK or 16QAM, is first applied to a size-M DFT. The output of the DFT is then applied to consecutive inputs of a size-N inverse DFT where N > M and where the (N-M) unused in

32、puts of the IDFT are set to zero. Also similar to OFDM, a cyclic prefix is inserted for each transmitted block.Figure 2-8 DFTS OFDM signal generationComparing (see Figure 2-8, “DFTS OFDM signal generation” ),with the IFFT-based implementation of OFDM modulation, it is obvious that DFTS-OFDM can alte

33、rnatively be seen as OFDM modulation preceded by a DFT operation.If the DFT size M equals the IDFT size N, the cascaded DFT and IDFT blocks of (see Figure 2-8, “DFTS OFDM signal generation”), will completely cancel out each other.However, if M is smaller than N and the remaining inputs to the IDFT are set to zero, the output of the IDFT will be a signal with low power variations, similar to a single-carrier signal. Besides, by varying the block size M the instantaneous