注塑常用術語英文表達

1、1。霧氣 Moisture Streaks2.玻纖分配不均Glass Fiber Streaks3.困氣 Gas Trap Effect4。銀絲紋 Sliver Marks5。結合線 Weld Line6。水波痕 Water Wave Effect7。黑點 Dark Sport8 .頂出印 Visible Ejector Marks9 .變形 Deformation During Demolding10。填充不足 Short Filling11。冷料流痕 Cold Slug12。進膠口 點不良 Dull Spots Near The Sprue13.噴射痕 Jetting14。表面起層 Fla

2、king Of The Surface Layer15。浮泡 Entrapped Air16.過熱變色 Burnt Streaks17。龜裂 Stress Crack18?？s水痕 Sink Marks19.真空氣泡 Density Bubble20。披鋒 Flash21 .擦傷Scratch MarksGlass fiber rich surface/glass emergence on the surface22 尺寸過大 Over dimension23 尺寸過小 Under dimension24 翹曲 Warpage/warped25 收縮 Shrinkage/shrink26 縮影

3、Sink marks27 打不滿 Short shot/short molding塑料模具 mould of plastics 注塑模具 injection mould沖壓模具die模架 mould base定模座板 Top clamping plateTop plateFixed clamp plate 水 口 推板 stripper plateA 板 A plateB 板 B plate 支承板 support plate 方鐵 spacer plate 底針板 ejector plate 面針板 ejector retainer plate 回針 Return pin導柱 Guide p

4、in有托導套 Shoulder Guide bush直導套 Straight Guide bush動模座板 Bottom clamp plateMoving clamp plate基準線datum line基準面datum plan型芯固定板 core-retainer plate凸模固定板 punch-retainer plate頂針 ejector pin單腔模具 single cavity mould多腔模具 multi-cavity mould多澆口 multi gating澆口 gate缺料 starving排氣 breathing光澤gloss合模力 mould clamping

5、force鎖模力 mould locking force擠出 extrusion開裂crack循環(huán)時間cycle time老化aging螺桿screw麻點pit嵌件insert活動鑲件 movable insert起堊 chalking澆注系統(tǒng)feed system主流道 sprue分流道runner澆口 gate直澆口 direct gate , sprue gate輪輻澆口 spoke gate , spider gate點澆口 pin-point gate測澆 口 edge gate潛伏澆口 submarine gate , tunnel gate料穴 cold slug well澆口套

6、 sprue bush流道板 runner plate排飛槽vent分型線（面）parting line定模 stationary mould , Fixed mould動模 movable mould , movable half 上模 upper mould, upper half下模 lower mould , lower half型腔cavity凹模 cavity plate , cavity block拼塊split定位銷dowel定位銷孔dowel hole型芯core斜銷 angle pin, finger cam滑塊slide滑塊導板 slide guide strip楔緊塊

7、heel block, wedge lock拉料桿 sprue puller定位環(huán) locating ring冷去口通 cooling channel脫模斜度draft滑動型芯slide core螺紋型芯threaded core熱流道模具 hotrunner mould絕熱流道模 insulated runner mould熔合紋 weld line (flow line )三板式模具 three plate mould脫模 ejection換模月空模具 interchangeable cavity mould脫模齊U release agent注射能力shot capacity注射速率 injection rate注射壓力 injection pressure差色齊U colorant保壓時間holdup time閉模時間 closing time定型裝置sizing system陰模 female mould , cavity block陽模 male mould電加工設備 Electron Discharge Machining數控加工中心 CNC machine center萬能鐵床 Universal milling machine臥式包床 Horizontal planer車床 Engine lathe平面磨床 Surface grinding mac