天行者X-8安裝手冊(簡體中文翻譯版)

1、 Skywalker X-8 Installation Manua天行者X-8安裝手冊 （漢化版） 翻譯 - China·天奇Thank you for Purchasing the Sky- walker X-8 Plane. The skywalker X-8 is designed for First-Person-Vision(FPV) application specifically.感謝您購買天行者X-8飛翼型飛機。天行者X-8是專為第一人稱飛行（FPV）而設計的。Technical parameters Wingspan：2120mm weight 880G motor

2、 2820 KV730 speed regulator 60A battery pack 4S8000MAH propeller 12X613X8技術參數：翼展：2120mm 空機重量880克 電機2820 kv730 電子調速器60A電池組4s 8000mah螺旋槳12x6 13x8 Take-off weight ：3200G設計最大起飛重量：3200gKIT version configuration：Fuselage, wing, winglet , tube, accessories bag, sticker包版本的配置：機身，機翼，翼梢小翼，碳纖維管，配件袋（包含，膠水、拉桿、螺絲

3、、層板、舵角、舵機延長線、強磁鐵），貼紙Parts Listing零件清單：如圖Assembly Glue the winglet layers, spread the glue evenly over the wing and both sides of the layers ( the layer marked with T board belongs to parts of the main wing )安裝說明：翼梢小翼層膠，涂膠均勻，兩側翼的層（層在標有T板屬于主翼部分）Wait for 5 minutes to allow glue to dry until it is non-s

4、ticky, then they can be glued in alignment ,等待5分鐘讓膠干直到不粘膩的，然后他們可以粘在對準Glue the hatch magnets , after compressing the magnet tightly, fix them with CA glue.膠艙口的磁鐵，磁鐵牢牢固定壓縮后，用快干固定膠如 401膠水或 502膠水。Glue the wood chip onto the hatch and fuselage, pay attention to the direction of SN of the magnetic pole膠合木

5、片上艙和機身，注意S/N磁極的方向After gluing, put it together and inspect the mounting spacing涂膠后，把它放在一起，檢查安裝間距Glue the servo, please choose the standard servo provided by skywalker or servo with moment more than 2.5 KG 膠伺服，請選擇由天行者或伺服安裝力矩超過2.5公斤標準伺服Glue the rudder horn, spread the glue evenly and wait for its dryn

6、ess, then Glue the rudder horn舵角膠，涂膠均勻，待其干燥，然后將舵角插入到副翼預留空位Power on the servo and place it in the mid-position , then lock the regulator screw, tighten the steel wire. And shorten the extra length of the wire.在中間位置放入伺服舵機，并鎖緊調節螺釘，擰緊鋼絲?？s短額外舵機導的線長度。Glue the fixed layer of the winglets, please be sure to

7、 spread the glue evenly and wait until it is completely dry, afterwards you can glue the layer.膠的小翼的固定層，然后你可以膠水層，請務必把膠水均勻，等待它完全干燥。Cut out the pre-reserved slot on the aileron only about 1,5 mm wide by a new blade切割預留插槽上的副翼只有大約1.5毫米寬，你需要的一個新的刀片，這樣可以切的更美觀。Wing plate bonding, please to smear evenly on

8、all surfaces, please not to spread the glue over the tube slot !翼板焊接，請均勻涂抹在所有表面，注意請不要把膠水在管槽！Settle the extending line in the line slot previously and spread the glue evenly over the plate.在解決延長線的線槽之前，把膠水均勻地分布在板。Wait for the two planes' dryness, later spread some glue over the vertical planes, an

9、d then fix and flatten them.等到兩個平面的干燥后,再來涂抹一些膠水在垂直的平面上，然后修復和壓平。The side plate bonding: spread the glue on both sides of the plate側板接合：兩側板上涂膠水It is recommended to insert the tube into the wing to guide the butt plate, which is more accurate.建議將碳纖維管插入翼引導對接板，這樣可以安裝的更準確。The line slot of early product al

10、so need to be widened to let the the extending line with plug directly into the fuselage.早期的產品線槽，也需要擴大，讓延長線與插頭直接插入機身。新的產品已經預留槽位。Fix the motor, and cement it to the fuselage in advance, you can also first fix the layer board base, and afterwards install the motor.固定發動機，與上下機身固定前，你也可以先固定層板，然后再安裝電動機。Spr

11、ead the glue on both sides of the fuselage, note:please avoid the tube slot!在機身的兩側，注意膠水的用量：請避免膠水流入管槽！After the two sides is dry, align and glue them雙方經過干燥，對齊和按壓機身 使膠水粘接完全。And then glue the butt plate of the fuselage.然后用膠水粘貼機身對接板。Still use the tube as a guide, align and glue it.仍然使用管為指導，使位置更準確，注意膠水的用

12、量。After gluing, you can butt the wing to make a trial of the accuracy, insert the extending into the fuselage through the line slot.涂膠后，您可以對機翼進行精度試驗，將延伸到機身采用線槽。We can see the butt is perfect.我們可以看到機翼與機身對接是完美的。As the airframe is designed to be very wide, you can easily put your FPV equipment down, an

13、d separate the transmitter and receiver.由于機身的設計是非常廣泛的，你可以很容易地把你的FPV設備、單獨的發射機和接收機裝入機艙。Fixing the wing is also very simple, just a screw, of course, if you don't trust this construction, you can also use a nut to butt.固定翼也很簡單，只是一個螺絲，當然，如果你不相信這個結構，你還可以使用一個反爪螺母。Fix the winglets with two 3 x8 screws,

14、 with the purpose of a long- term usage of the layer plate, it is suggested that consolidating the screw hole with CA glue before twist the screw.兩個3×8螺釘固定翼，和一個長的板層的長期使用的目的，建議鞏固螺絲孔擠入CA膠（螺絲膠）再擰螺絲。If you glue the motor frame previously, you can fix the motor now.如果你把發動機座之前已經安裝，你也可以現在安裝電機。We sugge

15、st you use brand quality propeller of CAM or APC .我們建議你使用CMA或APC品牌質量的推進器。We reserved the mounting positions of CCD holder and GOPRO我們保留CCD支架和GoPro的安裝位置You need to open a round hole in the corresponding position of the GOPRO's lens. And cut out a bevel to ensure not to obscure the vision of the w

16、ide-angle lens.你需要在這個GoPro的鏡頭的相應位置開一個圓孔。切口時確保不會影響到你的廣角鏡頭的視野。The position of the center of gravity of X - 8 is 440 mm away from the nose , 5 mm correction interval in front and at the back of it.X-8的重心位置 是離機鼻440毫米處 標注X的中心位置，前后允許有5毫米的誤差。The installed machine can be decomposed into small parts, which is easy to carry.機器的安裝可以分解成更小的部分，便于攜帶。Done!Finally, Please note that , control X - 8's flight speed within 85 km/H. If you need a high speed flight, please strengthen wings. please control the machine load within 3200 g, if exceed the limit, please strengthen wings. Thank you again for choosin