彈簧自動計算程序B版本

設計內容

頂目名稱

冷卷圓柱螺旋壓縮彈簧自動計算程序單輸入?yún)?shù) 輸出結果位彈簧剛度彈簧結構彈簧壓到位置荷重

材料切變模量G線徑d彈簧小端中徑D彈簧大端中徑D彈簧有效圈數n彈簧自由長度H0彈簧平均中徑D彈簧旋繞比C彈簧高徑比b修正系數K彈簧節距t彈簧間距δ彈簧壓并高度Hb最大變形量f工作變形量f螺旋角α材料展開長度L彈簧單重W彈簧中間增大值壓縮到H1H2H3H4試驗負荷壓并負荷是否要強壓處理

79000.00Mpa9.00mm58.88mm58.88mm17.14圈彈簧剛度441.40mm0.10mm時58.88mm旋繞比高徑比K值磨平不磨平磨平不磨平磨平不磨平磨平不磨平f1f2f3f4磨平不磨平展開長彈簧重自由回轉兩端固定荷重單Kgf位278.043025.09N308.3779.006710.91N684.108173.82N833.238173.82N833.233072.82N313.55磨平5067.25N517.07不磨平4817.26N491.56磨平0.66不磨平0.63

18.521.856.547.501.2324.9624.1815.9615.18167.76181.26273.64260.14163.36362.40441.40441.400.470.473540.471769.420.070.46下壓f1f2f3f4試驗負荷下的變形量壓并切應力壓并切應力強壓處理彈簧預制高度工作切應力H1H2H3H4試驗切應力荷重指定公差H1H2H3H4指定荷重下的長度公差H1H2H3H4公差匹配H1H2H3H4指定長度公差下的荷重范圍H1H2H3H4

τ1?τn單Kgf/mm2位τmin1764.87Mpa77.97τmax21696.79Mpa172.97τmax32066.68Mpa210.67τmax42066.68Mpa210.67[τ]Rmτs1580.00632.00Mpa64.490.40上下限值荷重范圍單Kgf位0.053025.14N308.380.053025.04N308.371.196712.09N684.221.196709.72N683.983.688177.50N833.613.688170.14N832.868173.82N833.238173.82N833.23長度上單下限值位上限0.00mm下限0.00mm上限0.06mm下限0.06mm上限0.20mm下限0.20mm上限0.00mm下限0.00mm輸入%數單Kgf位15.00453.76N46.260.00N0.000.00N0.000.00N0.00輸入長度荷重上單Kgf公差值下限值位0.303030.65N308.940.303019.54N307.810.306716.46N684.670.306705.35N683.548173.82N834.068173.82N834.068173.82N834.068173.82N834.06

指定變形量f1f2f3f4Kgf/mm2指定變形量f1f2f3f4指定變形量f2f3f4指定變形量f1f2f3f4彈簧穩定性彈簧設計校驗彈簧共振驗算彈簧疲勞強度及穩定性校驗

輸入GB值臨界負荷Pc0.171389.55N迫振ft輸入f/ft60.000.90自振頻率53.92τmax/Rm壓縮到γ下壓到2.000.45###1.073.000.37###1.314.000.37###1.31圖.壓縮、拉伸彈簧疲勞壽命算程序單位 Kgf/mmN/mm1.89Kgf/mmN/mm0.19Kgf/mmmmmmmmmmmmmmmmmmmmmmmmmm°°mmgmmmm輸入?yún)?shù)0.300.00

386.67mm222.49mm389.37mm233.29mm62.80%59.70%139.31%132.44%169.68%161.31%169.68%161.31%△D外徑增長△D增長值值0.460.43荷重單位Kgf5.56N0.570.00N0.000.00N0.000.00N0.00165.94mm1042.20Mpa106.35Kgf/mm2990.79Mpa101.10Kgf/mm2452.44mm1.03mm452.44應力單位Kgf/mm21.40Mpa0.140.00Mpa0.000.00Mpa0.000.00Mpa0.00上下限值荷重范圍單位Kgf5.56N0.570.00N0.000.00N0.000.00N0.000.00N0.000.00N0.000.00N0.000.00N0.00長度上下限值單位Kgf0.83N0.080.00N0.000.00N0.000.00N0.00荷重上單位Kgf下限值11.11N1.130.00N0.005.56N0.57(5.56)N(