常用模具零件中英文對照表.doc

常用模具零件中英文對照表 2005-12-19 14:51:17中國注塑網 一、 入水：gate 進入位：gate location 水口形式：gate type 大水口：edge gate 細水口： pin-point gate 水口大?。篻ate size 轉水口：switching runner/gate 唧嘴口徑：sprue diameter 二、流道: runner 熱流道：hot runner,hot manifold 熱嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圓形流道：round(full/half runner 流道電腦分析：mold flow analysis 流道平衡:runner balance 熱嘴：hot sprue 熱流道板：hot manifold 發熱管：cartridge heater 探針: thermocouples 插頭：connector plug 插座： connector socket 密封/封料： seal 三、運水：water line 喉塞：line lpug 喉管：tube 塑膠管：plastic tube 快速接頭：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 邊釘/導邊：leader pin/guide pin 邊司/導套：bushing/guide bushing 中托司：shoulder guide bushing 中托邊：guide pin 頂針板：ejector retainner plate 托板：support plate 螺絲： screw 管釘：dowel pin 開模槽：ply bar scot 內模管位：core/cavity inter-lock 頂針：ejector pin 司筒：ejector sleeve 司筒針：ejector pin 推板：stripper plate 縮呵：movable core,return core core puller 扣機（尼龍拉勾）：nylon latch lock 斜頂：lifter 模胚（架）： mold base 上內模：cavity insert 下內模：core insert 行位（滑塊）： slide 鑲件：insert 壓座/斜雞：wedge 耐磨板/油板：wedge wear plate 壓條：plate 撐頭: support pillar 唧嘴： sprue bushing 擋板：stop plate 定位圈：locating ring 鎖扣：latch 扣雞：parting lock set 推桿：push bar 栓打螺絲：S.H.S.B 頂板：eracuretun 活動臂：lever arm 分流錐：spure sperader 水口司:bush 垃圾釘：stop pin 隔片：buffle 彈弓柱：spring rod 彈弓:die spring 中托司：ejector guide bush 中托邊：ejector guide pin 鑲針：pin 銷子：dowel pin 波子彈弓：ball catch 喉塞:pipeplug鎖模塊：lockplate斜頂：anglefrompin斜頂桿：angleejectorrod尼龍拉勾：partinglocks活動臂：leverarm復位鍵、提前回桿：earlyreturnbar氣閥：valves斜導邊：anglepin術語：terms承壓平面平衡：partingsurfacesupportbalance模排氣：partinglineventing回針碰料位：returnpinandcavityinterference模總高超出啤機規格：moldbaseshuthight頂針碰運水：waterlineinterfereswithejectorpin料位出上/下模：partfromcavith(core)side模胚原身出料位：cavitydirectcutonA-plate,coredirectcutonB-plate.不準用鑲件：Donotuse(core/cavity)insert用鈹銅做鑲件：useberylliumcopperinsert初步（正式）模圖設計：preliinary(final)molddesign反呵：reversecore彈弓壓縮量：springcompressedlength穩定性好：goodstability,stable強度不夠：insufficientrigidity均勻冷卻：evencooling扣模：sticking熱膨脹：theroexpansion公差：tolorance銅公(電極）：copperelectrode 塑件模具相關英文詞匯出處：FanE翻譯中國 作者：(轉載) FanE翻譯中國 2005-12-16 20:41:59如需轉載，請注明來自：FanE翻譯中國http;/www.FanE.cncompre sion molding壓縮成型 flash mold溢流式模具 plsitive mold擠壓式模具 split mold分割式模具 cavity型控 母模 core模心 公模 taper錐拔 leather cloak仿皮革 shiver飾紋 flow mark流痕 welding mark溶合痕 post screw insert螺紋套筒埋值 self tapping screw自攻螺絲 striper plate脫料板 piston活塞 cylinder汽缸套 chip細碎物 handle mold手持式模具 encapsulation molding低壓封裝成型、射出成型用模具 two plate兩極式（模具） 如需轉載，請注明來自：FanE翻譯中國http;/www.FanE.cnwell type蓄料井 insulated runner絕緣澆道方式 hot runner熱澆道 runner plat澆道模塊 valve gate閥門澆口 band heater環帶狀的電熱器 spindle閥針 spear head刨尖頭 slag well冷料井 cold slag冷料渣 air vent排氣道 welding line熔合痕eject pin頂出針 零件英語 punch沖頭 insert入塊(嵌入件) deburring punch壓毛邊沖子 groove punch壓線沖子 stamped punch字模沖子 round punch圓沖子 special shape punch異形沖子 bending block折刀 roller滾軸 baffle plate擋塊 located block定位塊 supporting block for location 定位支承塊 air cushion plate氣墊板 air-cushion eject-rod氣墊頂桿 trimming punch 切邊沖子 stiffening rib punch = stinger 加強筋沖子 ribbon punch 壓筋沖子 reel-stretch punch 卷圓壓平?jīng)_子 guide plate 定位板 sliding block 滑塊 sliding dowel block 滑塊固定塊 active plate 活動板 lower sliding plate 下滑塊板 upper holder block 上壓塊 upper mid plate 上中間板 spring box 彈簧箱 spring-box eject-rod 彈簧箱頂桿 spring-box eject-plate 彈簧箱頂板 bushing bolck 襯套 cover plate 蓋板 guide pad 導料塊 14. electrical discharge machining (EDM)電火花加工15. electrical insulating property電絕緣性能16. electrochemical die-sinking machine電解型腔加工機，電解型腔加工機床17. electrochemical machine (ECM)電解加工機床，電化學加工機床18. electrochemical machining (ECM)電解加工，電化學加工19. electro-discharge cutting電火花加工，電火花切割20. electro-discharge cutting machine電火花切割機21. electro-discharge machine tool電火花加工機床22. Electro-discharge Machine電火花加工機床23. electro-discharge machining電火花加工24. electro-discharge machining process電火花加工工藝，電火花加工工序25. epoxy resin環氧樹脂9. guide bushing導套10. guide pillar導柱，導桿，導柱11. guide pin導向銷，導桿12. guide pin cover導柱蓋13. guide plate導料板，導板14. guide plate blanking die導板式?jīng)_裁模，導板式落料模15. guide post導柱，導柱16. guide stock plate擋料板4. injection mold注射模，注塑模5. injection molding注射成型，注塑成型6. injection-molding machine注塑機，注射機，注塑成形機7. injection plunger注射柱塞8. in-line reciprocating screw聯機往復螺桿，串聯往復螺桿，直線排列往復螺桿9. inner ram內滑塊10. inserting molding嵌件成形11. integrated manufacturing集成制造12. internal stress內應力13. intermediate platen中間板，隔板塑料成型模具的主要設計要素脫模距 stripper distance脫模斜度 draft投影面積 projected area最大開距 maximum daylight;open daylight閉合高度 mould-shut height抽芯距 core-pulling distance抽芯力 core-pulling force脫模力 ejector force開模力 mould opening force模內壓力 internal mould pressure;cavity pressure成型壓力 moulding pressure背壓環 back-up ring1 bar = 14.5psi高壓接頭 bite type fitting液壓馬達 hydraulic motor冷卻水流量計 waterflow regulator打磨器材 abrasive material打磨砂輪 grinding wheels切割砂輪 cutting wheels碼模夾(注塑機使用) mould clamps; lifting clamps小五金工具 piping tools高壓力軟管 high pressure hose風管,水軟管 air .water hose高壓油表 pressure gauge壓力油喉 hydraulic hoses光塑檢測 photoelastic testing吹塑模 plastic blow mould注塑模 plastic injection mould沖扎復合模 blank & form compound die精密沖模 precision blanking die熔料流動率 MFR=melt flow rate熔料流動指數 MET=melt flow index推板導柱 guide pin for ejector plater座板 clamping plate墊塊 space block(plate)推板 ejector block(plate)afdek plate 檔塵板guide stripe 行位后板cavity sub-insert 前模鑲件core sub-insert 后模鑲件sprue puller insert 扣針鑲件stage ejector 頂棍spacer rock(risers) 間隔板變形 distortion彎曲 warp拖花 drag marks火花紋 EDM marks困氣 venting燒黑 burns表面縮水 shrinkage料位過薄/砸穿 thin wall stock走水不平行 uneven fill pattern夾水紋/流紋 witness line;mismatch;stress marks走水紋 knit lines走水不齊 short shotsorifice 料口nozzle seat 熱嘴墊圈nozzle plate 射嘴板cross pin 十字頭銷sled 射臺seal ring 封密圈spacer rail 介子座heater groove 發熱管槽heater cement 發熱管的結合劑soak 浸泡seat 墊圈ream 鉸大圓孔直徑grind 磨床drill 鉆床mill 銑床caliper 卡尺G-caliper 分厘卡Depth Gauge 深厚計hardness tester 硬度計angle gauge 角規marble table 云臺石projector 投影儀height gauge 高度儀microscope 顯微鏡plug gauge 塞規 leveller 水平器R gauge R 規Inter caliper 內分厘卡surface 平面儀item number 細目編碼catalog number 材料分類編碼undercut lip 倒扣口hot tip = hot drop = nozzle 熱嘴blow-off strip 放氣板blow-off nozzle 吹風口spiral hose 螺旋式的連接喉rust solvent 除銹劑shaft 曲軸tensile strength 拉伸力yield strength 屈服力spark erosion 電火花蝕刻etch(photo-etch) 電蝕harden 淬硬copper electrode 銅公corrosion resistance 耐腐蝕anneal 退火heat treatment 淬火FEM(finite elemnet method) 有限元法preliminary tool design 初期模具設計圖zone 熱流道區域reverse taper 倒啤把clamp plate 碼板toggle clamp 快速夾vacuum furnace 真空爐cavity insert rounds 圓柱鑲件cavity insert b0locks 方柱鑲件tensile strength 抗張強度,抗拉強度Concept drawing 概念圖Assembly drawing 裝配圖mismatch;witness line 夾紋shut-off(n.) 枕位venting valves 疏氣閥venting plug 疏氣塞valve casing 閥門罩twist drill 旋鉆harden/nitride 碎硬anneal 退火temper 回火stess crack 應力斷裂corrosion resistance 防腐,防銹tensile strength 物】抗張強度,抗拉強度split mould (分離)組合式的模具inclined plate 斜面inclined bolt 斜栓jaw (工具,機械等)夾住東西的部分,鉗口step change of the P/L 分形面枕位的改變thin steel section 較薄的料位clean-up 清理,清除,清掃M(jìn)old Dating Insert 模具日志鑲件Hot Sprue Bushing 熱澆口套semi-automatic 半自動quick disconnector 快速斷開接頭full shot 足量注射mismatch 夾痕;夾水紋ejector mark 頂痕screw boss 螺絲孔,螺絲基座sink mark 縮坑15% glass filled ABS 摻有15%玻璃的ABSspraying mold release 脫模劑drag mark 拖痕stress mark 應力痕reinforcement rib 加強筋slght stoning 輕度磨砂soliid line 實線dotted line 虛線internal diameter 內徑external diameter 外徑nickel-plated 電鍍的handling hole;lifting hole 吊裝孔parallel 平行塊piston 活塞plunger 柱塞carrier 導軌rest 支架item number 項目編號catalog item 商品目錄編碼dimensional datum 尺寸基準heat treatment certification 淬硬證明文件back-up bushing 支撐導套jacking screw 起重螺絲,千斤頂tapped hole (帶有螺旋角度的)螺絲孔diagonal corner 成對角的角落burn mark 燒痕hot runner mainfold (熱流道板)分流板texuring 蝕紋clamping screw (注塑機)碼模螺絲imperial 英制的metric 公制的puller bushing 水口套puller bar 水口鐵drool bushing 防漏膠套筒safety switch 限位制water line connected internally or hard tubing 不可用膠喉連接運水lifter on square rod or locked from rotation 用方形柱或用管釘止轉gate insert 入水鑲件gate shut-offs 流道開關配件guided ejection 中托司parting line shutoff 前后模接觸面waterlines clear tie bars. 運水喉咀接駁位要避開啤機呵林柱.BGV=Balanced Gate Value 平衡入水值spacer 墊塊pocket 挖槽rough 粗加工finish 精加工plunge rate 進刀率retract rate 提刀速率splindle rate 主軸轉速coolant 冷卻液SPLIT RING 開口環(鑰匙圈)側向抽芯力 side pulling-core forceconvert.transfer 轉圖guide pin 邊針Tee slot cutter T形SLOT CUTTERzigzag 雙向切削constant overlap spiral 等距環切parallel spiral 環繞切削parallel spiral clean corners 環切并清角morph spiral 依外形環繞true spiral 螺旋切削one way 單向end mill 平銑刀spher mill 球刀bull mill 圓鼻刀face mill 面銑刀rad mill 圓角成型刀chamfer mill 倒角刀slot mill 槽刀taper mill 推拔銑刀dove mill 鳩尾銑刀lot mill 棒狀drill 鉆孔reamer 紋刀bore bar 搪刀tap RH 右牙刀Tap LH 左牙刀ctr Drill 中心鉆spot drill 點鉆cntr bore 沉頭孔刀c. sink 魚眼孔鉆loft surface 舉升曲面coons surface 昆氏曲面ruled surface 直紋曲面revolved surface 旋轉曲面swept surface 掃描曲面draft surface 牽引曲面grinding wheel 磨砂使用的輪子quench steel 將.淬火,使冷卻stress relieving 應力消除molten 熔熱的oxide film 氧化層guide pin and sleeve, locating ring ,導邊,司筒,定位圈ejector ,ejector balde, ejector sleeve,頂針,扁頂針,頂針?biāo)就?lifters, wear plate,horn pin,斜坊,磨損板,氣頂針,O ring, water baffle, water pipe plug,O形圈,隔片,運水管道塞,water line connector,wear plate ,運水管道轉接頭,耐磨板air cylinder,hydraulic cylinder,氯壓缸,液壓缸micro switch,oil nipple, spring,開關裝置,油槍接頭,彈弓sprue bushing,early return system,澆口套,早期回撞裝置,accelerated ejectors, slied holder,加速頂針,注塑周期計數器,cycle counter,date stamper，滑塊固定板,生產日期銘牌,hot runner system ，熱流道系統chemical composition 化學成份thermal conductiivity 導熱性能thermal diffusivity 熱擴散性能dimensonal stablity 尺寸穩定性能cooling effiency 冷卻效率easiler ejection 易于脫模alloy insert 合金鑲件(cooling) duct 輸送管;導管maintenance cost 維護費用ultrasonic testing 超聲波檢測crack 斷裂direct gate 直接澆口ring gate 環形澆口disk gate;disphragm gate 盤形澆口spoke gate;spider gate 輪輻澆口pin-point gate 點澆口edge gate 側澆口submarine gate;tunnel gate 潛伏澆口fan gate 扇形澆口tab gate 護耳澆口runner plate 流道板(或冷或熱)secondary nozzle 二級噴嘴torpedo;torpedo body assembly 魚雷形組合體catridge heater 管式加熱器heat pipe 熱管 valve gate 閥式澆口force plunger;pot plunger 柱塞flash groove;spew groove 溢料槽impression;cavity block;cavity plate 凹模punch;force 凸模movable insert;loose detail 活動鑲件cavity splits;core splits(凹模拼塊) (型芯拼塊) 拼塊side core 側型芯thread plug;threaded core 螺紋型芯thread ring;threaded cavity 螺紋型環cutting wheel 切割砂輪grinding wheel 打磨砂輪abrasive material 打磨器材mould clamps;lifting clamp 砂模夾(注塑機使用)air (water) hose 風管,水輪管pressure gauge 高壓油表hydraulic hose 壓力油喉plastic blow mould 吹塑模plastic injection mould 注塑模blandk&form compound die 沖扎復合模precisiion blanking die 精密沖模MFR=melt flow rate 熔料流動率MFT=melt flow index 熔料流動指數handling hole 拉鈴孔stop plate 限位塊linder bush 襯套spacer block(plate) 墊塊,方鐵back-up ring 背位環standoff 限位塊American Safety Hoist Rings. 英制安全吊裝環Mechanical Properties 機械性能Tensile Strength(MPa) 抗拉強度elongation 延伸率hardness(Brinell) 硬度shear stength(MPa) 剪切力impact strength 沖韌性Physical Properties 物理性能solidification shrinkage 凝固收縮率freezing range 凝固與熔范圍thermal expansion 熱膨脹系數specific heat 比熱t(yī)hermal conductivity 熱導率electrical conductivity 電導率micro-structure 金相分析hot work tool steel 熱作鋼circular motion 環形運動variable 變數,參數graphics window 圖形窗口45 degree entry and a zero degree exit. 進刀口45度,退刀口0度runner stripper plate 脫料板stripper plate 活動板spacer rock(risers) 間隔板stage ejector 頂棍sprue puller insert 扣針導套guide strip 行位后板afdek plate 擋塵板side gate 大水口pinpoint gate 細水口SHCS 杯頭螺絲FHCS 平頭螺絲set screw 無頭螺絲ball catch 波子螺絲wedge 行位較杯gib 線條,(撐雞的導軌)latch 拉桿clamp 碼仔spring guide pin 彈弓導柱steel pad disc 橙仔方ejector cam insert 斜頂塊(screw) nut 螺母taper 嗲把/ 斜度taper interlock 嗲把鎖texture 花紋toggle-lok 回撞裝置top clamping plate 頂碼板unified national coarse (UNC) 美制螺絲(粗牙)unified national fine (UNF) 美制螺絲(幼牙)set screw 噴頭螺絲side gate 大水口slide retainer 行位管位water junction 喉咀spacer block 登仔jiffy-matic socket 喉咀套jiffy-tite plug 喉咀公spring plunger 彈弓座sprue puller 勾針/勾粒spring washer 彈簧塑圈stepped ejector pin 有托頂針strippers plate 推板/細水口板submarine gate 潛水口support pin 拉桿support plate 暗板surface finish 光潔度alignment strip 斜鎖angle pin 斜針fan gate 扇形入水fillet 圓口ball catch 彈弓波子blade ejector 扁頂bottom clamping plate 底碼板free length 自然長度bridge piece 水口鐵helix spindle 鍋桿hose clip 水喉箍bubbler 隔氣運水jiggle 斜頂jiggle witness line 斜頂片位置center distance (CRS) 山打距離(中心線距離)clamp 碼仔contour 外形leader pin 導針location ring(flange) 法蘭counterbore 拔頭,介子托mock-up;prototype 手辦die cast 合金壓鑄national pipe thread(NPT) 美制喉牙overflow 垃圾位ejection sleeve 司筒,頂套epoxy 膠樣pin point gate 細水口pressure plug 喉塞pressure spring 壓力彈簧parting line flash 披鋒burned 燒黑underfilled 缺料insert mismatch 鑲件夾口ejector pins not flush 頂針有高低ejector pins skid 頂針滑動insert flash 鑲件披鋒pressure transducer 壓力探測頭hydraulic schematic 油積筒油路接駁圖jiffy connector recessed 安裝喉嘴后不可突出模胚knock out pullback stud -flush with clamp plate 頂棍鑲件與底板有否空間safety switches 限位