CiscoPacketTracer實驗7RIP路由協議的配置

1、 實驗7：RIP 路由協議的配置一、實驗目的1、練習RIP 動態路由協議的基本配置；2、掌握了解RIP 路由協議原理二、實驗環境：Packet tracer 5.0三、關于RIP 的基礎知識RIP（Routing Information Protocol）是最常使用的內部網關協議(InteriorGateway Protocol)之一，是一種典型的基于D-V 算法的動態路由協議。通過UDP（User Datagram Protocol）報文交換路由信息，使用跳數（HopCount）來衡量到達目的地的距離（被稱為路由權Routing cost）。由于在RIP 中大于或等于16 的跳數被定義為無窮

2、大（即目的網絡或主機不可達），所以RIP 一般用于采用同類技術的中等規模的網絡，如校園網及一個地區范圍內的網絡，RIP 并非為復雜、大型的網絡而設計。啟動RIP，進入RIP 視圖： router Rip關閉RIP： no rip在指定的網絡上使能RIP network network-number| all 在指定的網絡上禁用RIP no network network-number| all四：實驗步驟：拓撲圖如下所示：配置過程：Router1：Routerenable /進入特權模式Router#conf ter /進入全局配置模式Enter configuration commands,

3、 one per line. End with CNTL/Z.Router(config)#int f0/0 /配置Fa0/0 接口Router(config-if)#ip add 1.1.1.2 255.255.255.0Router(config-if)#no shutdown %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to upRouter(config-if)#%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed stat

4、e to upRouter(config-if)#exitRouter(config)#int s0/0/0 /配置串口Router(config-if)#ip add 1.1.6.1 255.255.255.0Router(config-if)#clock rate 64000Router(config-if)#no shutdown %LINK-5-CHANGED: Interface Serial0/0/0, changed state to downRouter(config-if)#exitRouter(config)#int s0/0/1 /配置串口Router(config-if

5、)#ip add 1.1.2.1 255.255.255.0Router(config-if)#clock rate 64000Router(config-if)#no shutdown %LINK-5-CHANGED: Interface Serial0/0/1, changed state to downRouter(config-if)#exitRouter(config)#router rip /進入RIP 視圖Router(config-router)#network 1.0.0.0 /發布直連網絡Router(config-router)#exitRouter(config)#ex

6、itRouter#%SYS-5-CONFIG_I: Configured from console by consoleRouter#show ip route /查看路由表Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF exte

7、rnal type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static routeGateway of last resort is not set 1.0.0.0/24 is subnetted, 1 subnetsC 1.1.1.0 is dire

8、ctly connected, FastEthernet0/0Router#Router2：Routerenable Router#conf terEnter configuration commands, one per line. End with CNTL/Z.Router(config)#int f0/0Router(config-if)#ip add 1.1.5.2 255.255.255.0Router(config-if)#no shutdown %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LIN

9、EPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upRouter(config-if)#exitRouter(config)#int s0/0/1Router(config-if)#ip add 1.1.2.2 255.255.255.0Router(config-if)#clock rate 64000Router(config-if)#no shutdown %LINK-5-CHANGED: Interface Serial0/0/1, changed state to upRout

10、er(config-if)#exitRouter(config)#int s0/0/0Router(config-if)#ip add 1.1.3.1 255.255.255.0Router(config-if)#clo rate 64000Router(config-if)#no shutdown %LINK-5-CHANGED: Interface Serial0/0/0, changed state to downRouter(config-if)#exitRouter(config)#router ripRouter(config-router)#network 1.0.0.0Rout

11、er(config-router)#exitRouter(config)#exitRouter#%SYS-5-CONFIG_I: Configured from console by consoleRouter#Router#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 -

12、OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static routeGateway of last resort is not set 1.0.0.0/24

13、is subnetted, 3 subnetsR 1.1.1.0 120/1 via 1.1.2.1, 00:00:11, Serial0/0/1C 1.1.2.0 is directly connected, Serial0/0/1C 1.1.5.0 is directly connected, FastEthernet0/0Router#Router3：RouterenRouter#conf terEnter configuration commands, one per line. End with CNTL/Z.Router(config)#int f0/0Router(config-

14、if)#ip add 1.1.4.2 255.255.255.0Router(config-if)#no shutdown %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upRouter(config-if)#exitRouter(config)#int s0/0/0Router(config-if)#ip add 1.1.6.2 255.255.255

15、.0Router(config-if)#clo rate 64000Router(config-if)#no shutdown Router(config-if)#%LINK-5-CHANGED: Interface Serial0/0/0, changed state to upRouter(config-if)#exitRouter(config)#int s0/0/1Router(config-if)#ip add 1.1.3.2 255.255.255.0Router(config-if)#clock rate 64000Router(config-if)#no shutdown %L

16、INK-5-CHANGED: Interface Serial0/0/1, changed state to upRouter(config-if)#exitRouter(config)#router rip Router(config-router)#%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0/1, changed state to upRouter(config-router)#network 1.0.0.0Router(config-router)#exitRouter(config)#exitRouter#%SYS

17、-5-CONFIG_I: Configured from console by consoleRouter#show ip rouRouter#show ip route Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF exter

18、nal type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static routeGateway of last resort is not set 1.0.0.0/24 is subnetted, 6 subnetsR 1.1.1.0 120/1 via 1.1.6.1, 00:00:02, Serial0/0/0R 1.1.2.0 120/1 via 1.1.6.1, 00:00:02, Serial0/0