鑫狼旭貼片3610ZX規格書

1、深圳市鑫狼旭電子有限公司Shenzhen X.L.X. Electronics Co., Ltd.承認書SPECIFICATIOM FOR APPROVAL客Customer規格型號:戶:LX3610Part No樣品編號：Sample Code NoLX20160108010客戶確認/Customer Approved料 號/Part No.簽 章/Signatures地址: 廣東省深圳市龍華新區民治街道橫嶺五區電話號碼真號碼成/Drawn批準/Approved審核/Check薛陽王輝董冬根深圳市鑫狼旭電子有限公司文件名稱作成薛陽審

2、核產品規格書批準文件編號LX3610版本版次黃明富A/O制修訂履歷日期2015-6-13版本版次制修訂內容頁次制修訂人A/O新制訂陳小彥規格書目錄List of specifications適用范圍/General使用條件/Operating condition測定條件/Measuring condition機械要求/Mechanical specification性能特征/Performance and characteristics可靠性/Reliability要求/Requires注意事項/Matters to be paidattention to when using motor外形

3、圖/ Outline drawing包裝/Packing2015-6-13產品型號Original Model規格書SpecificationLX3610(LEAD WIRE)編號LX36101. 適用范圍 Ceneral本規格書適用于圓筒式永磁直流電機 LX3610-07250/25 型This specification applies to cylindrical permanent-magneticmotorsDCmodelLX3610-07250/252使用條件Operating condition項目/Item2-12-22-32-42-52-62-72-8額定電壓Rated vo

4、ltage額定負荷Rated load負載轉速No-load speed旋轉方向Rotation馬達位置Motor position使用電壓范圍Operating voltage使用環境Operating environment保存環境Storage environment項目/Item3-13-23-3溫度Temperature濕度Humidity位置Motor position20±2(6367)RH軸向Motor shaft horizontal將馬達固定在試驗臺上Lock the motor in a test fixture3.0V DC振子Vibration weight

5、12000±2000 rpmCW(clockwise) or CCW(contraryclockwise)全方位All position2.34.5V DC-3070,Ordinary Humidity-4080,Ordinary Humidity無水氣凝結No condensation of moisture無水氣凝結No condensation of moisture條件·備注/Condition remark見外形圖As specified in ortine drawing規格/Specification條件·備注/Condition remark測定條

6、件Measuring condition規格/Specification 所有數據都是在溫度 20，濕度 65的條件下測得的。判定有異議時，在溫度35、濕度4585的范圍內測試All data are based on the measurement under the temperature of 20 and humidity 65RH .however .There anges oftemperature 535 and humidity 4585RH are to be applicable as long as no problems4. 機械要求Mechanical specifi

7、cation項目/Item4-14-2外觀Appearance軸向間隙Shaft end play結構Configuration規格/Specification見外形圖As specified in outline drawing不含有機械損壞及不充分的浸蝕等。There shall be no evidence ofmechanical damage and shall nothave inadequate corrosion and so on0.05 0.3 條件·備注/Condition remarkOutline drawing No:LX3610(LEAD WIRE)目測

8、（容許范圍根據樣品外形）Visual examination(allowableextent is based on boundarysample)4-3201412-314-4質量Mass振子軸向拔出力Holding strengthof vibration weight項目/Item5-15-25-3負載轉速No-load speed負載電流No-load current堵轉電流Stall current起動電壓Starting voltage絕緣電阻Insulation resistance端子阻抗Terminal resistance機械噪音Mechanical noise規格書Spe

9、cification0.6g Approx編號LX3610機體Body+振子/Vibration 0.6g+0.3g4-520N(2kgf)性能特征Performance and characteristics規格/Specification12000±2000rpm85mA Max90±10mA條件·備注/Condition remark在額定電壓和額定負載（振子）下At rated voltage and rated load(vibration weight).在額定電壓下At rated voltage在額定負載（振子）下電樞的任意位置。5-42.3V D

10、C MaxAtrated load (vibratiomweight) any position of rotor.5-55-65-710 M Min30±10小于 50 分貝A 計權 50db(A)Max在 100V 直流下，導線和機殼間At DC 100V between lead wire and case.在 20下At 20在額定電壓、額定負載（振子）下。At rated voltage and rated load (vibration weight).背景噪音：不大于 28db.A 計權Back ground noise 28db(A) Max測試儀器：BakMeasu

11、ring instruments:Bak夾具重量：700gWeight of jig:700g2015-6-136.可靠性Reliability項目/Item規格書Specification編號BA3610規格/Specification判定標準Judgment在常溫濕下放置 2H 后，馬達應符合項 7-1 的要求After 2hours exposuretemperaturemotorsasandbeinshallin6-1壽命Life位置Position軸水平Horizon軸水平Horizon電壓VoltRated額定rated額定負荷LoadWeight振子Weight振子溫度Temp2

12、040濕度Humi65%90%壽命Life100,000Cycles20,000Cyclesordinaryhumidity,approvedisem7-1.specified6-2低溫放置Low tempexposure高溫放置High tempExposure溫度時間溫度時間/Temperature :-4±2/Time:96/Temperature :85±2/Time:96在常溫濕下放置 2H 后，馬達應符合項 7-的要求After 2 hours exposureIn6-3溫度/Temperature :60±2/Humidity:9095%RHordi

13、nary temperature andhumidity, motors shallbeapproved as specified in isem7-.6-4濕度放置Humidityexposure濕度放置時間干燥時間/Exposure time : 96/Dry time: 4h無水氣凝結 /No condensation of moisture全振幅頻率周期/Displacement :1.5 (p-p)/Frequency/Period:10 to 55Hz:20min 范圍內(105510Hz)測試結果應符合項 7-2 的要求After the test motors shall be

14、approved as specified in item7-2.6-5 振動Vibration方向時間/20 Minutes log sweep(105510Hz)/Direction/Time/Each 2 hours試驗狀態/Test state:將馬達固定在約 100 克（包括馬達本身）的物體上，落向水泥地面Set the motor to the approximately 100g(include the motor) weight of block drop the: x、 y、 z:每h測試結果應符合項 7-2 的要求After the test motors shall be

15、approved as specified in item7-2.6-6自然跌落Free fallmotor on the concrete floor.高度方向次數/Height/Direction方向次Each 2 times:1.5m:± x.± y.± z/Number of times:每個2016-1-8規格書Specification編號LX3610測試結果應符合項 7-2 的要求6-7熱沖擊Heat stock test周期 Period: 32常溫常濕下放置 24 小時測試Exposed at ordinary temperature andor

16、dinary humidity for 24before measurementhoursAfter the test motors shall beapproved as specified in item7-2.7.要求Requirements項目/Item判定基準Requirements1)額定轉速Rated speed:不低于初始值30;不高于初始值+60data-30 Initial Mindata-60 Initial Max2)額定電流Rated current:不大于初始值±30 Initial:data±30 Max7-1表Table A3)絕緣電阻Ins

17、ulation resistance :大于 10M10M Min4)起動電壓Starting voltage:最大 2.3V 直流電壓2.3V DC Max5)波形Current wave:波形正常No blot current wave1)額定轉速Rated speed：不低于初始值30;不高于初始值+60data-30 Initial Min7-2表Table Bdata-60 Initial Max2)額定電流Rated current3)起動電壓Starting voltage:不大于初始值±30 Initial:最大 2.3V 直流電壓2.3V DC Max2016-1-

18、8規格書Specification編號LX3610 4mm 振動馬達包裝Pack drawing of 4mm cylindrical type1m=84PCS（1 Tray）包裝試驗要求/Package Test Requirement:標準/Criterion:1.整箱重量小于等于 9Kg,跌落高度設定為 75cm. /The weight of the whole carton less than 9Kg,the.2.整箱重量大于 9Kg 但小于等于 23Kg 的，跌落 高度設定為 60cm. /The weight of the whole carton more than 9Kg and Les than 23Kg, the dropping height is 60cm.試驗方法/Test Methods:跌落要求為六面三棱一角。/Dropping requirement is6 faces,3 arris,1 angle.六面：先從最大兩面跌，然后是中間大小的兩面， 最后跌最小的兩面，一共六次。 /6 faces :First dropping with two biggist faces,: Than dropping