化妝品灌裝包裝生產記錄

1、精品LOTION AND GEL FILLING BATCH PRODUCTION RECORD 化妝品灌裝包裝生產記錄起草/日期 DRAFT BY: 審核/日期 CHECKED BY: 生效日期 ISSUE DATE: 可編輯修改SUPERVISOR PRE-FILLING REVIEW （CHECK ALL THAT APPLY）-灌裝前主管復核目錄 （如被執行，請打鉤號）ALL MATERIAL OF PREVIOUS PRODUCTS MUST HAVE BEEN CLEARED AND CLEANED.上批產品所余物料已清除或退料，以防交叉污染。THE FILLING EQUIPME

2、NT AND SURFACE OF LINE MUST BE INTEGRITY AND HAS BEEN CLEANED. THE RESULTS MUST BE RECORDED.灌裝設備和流水線表面完整及功能正常，已被清潔消毒并記錄。BEFORE STARTING PRODUCE. THERE MUST HAS STANDARD SAMPLE ON LINE.產品是否有標樣。ALL BULK HAVE STAGED, IDENTIFIED AND ARE WITHIN EXPIRATION DATE所有半制品及包裝材料有標識，準備就緒，確認無誤，并在有效期內.ALL EQUIPMENT

3、HAS BEEN CLEANED所有設備按照已被清潔消毒.THE FORMULA HAS BEEN ISSUED AND APPROVED BY THE QUA LITY CONTROL DEPARTMENT此生產記錄是否由品保部門發放和確認.THE FILLING AND PACKAGING PERSONNEL ASSIGNED TO THIS BATCH HAVE BEEN TRAINED灌裝和包裝此批產品的配制工是否被適當?shù)嘏嘤?xùn).PACKAGING SUPERVISION HAS REVIEWED ALL THE REQUIREMENTS WITH THE PERSONNEL ASSIG

4、NED TO FILL AND PACKAGE THIS BATCH包裝部門管理人員已確認灌裝和包裝所需的所有必要條件 DATE （日期）:SUPERVISOR （生產主管）工序WorkingProcedure操作Operati on記錄Record操作人/時間Operate by復核人/時間Check by備料Prepare將瓶子和泵頭去掉包裝，放入潔凈的塑料筐中，紫外殺 菌半小時，將要灌裝的內料拖到相應的灌裝線上，將外 箱標簽和塑料袋清潔后拖到包裝線上Take off the package of the bottle and pump, put into the clean plasti

5、c box, sterilizationwith UV,andpull all the other componentson thepackaging line.瓶批號 Bottle Batch No.: 泵批號 pump Batch No.: 半制品批號Bulk Batch No.:灌裝Fill先將灌裝機的灌裝量調整到規定值，將灌裝機頭對準 瓶口進行灌裝。然后插入泵頭，旋緊并鎖口 Adjust thefilling quantity, begin to fill, then insert the pumpand make it tight and locked.半制品數量Bulk Quant

6、ity :kg單瓶灌裝量 Per Bottle Qty. :G噴碼Sprinkle Code噴碼位置是否正確噴碼內容是否完整Made in China11Label Batch No.:MFG :收縮膜封口Seal調整吹風機溫度，將收縮膜套于泵頭進行封口Adjustthe temperature then put the shrink film on thepump and seal firmly.封口機溫度設置 Temperature :oC封口是否牢固裝箱En caseme nt按照每6PCS套上塑料袋（袋口朝上）裝入一外箱，封好 外箱箱底，貼好外箱標 sealed the bottom.

7、 Put every 6 with the plastic bag into the carton and attached theUPC label實際包裝規格Packaging Specificationin Fact :瓶/箱.封箱En velop用透明膠帶將外箱兩端和中縫封牢，堆碼在棧板上。每層 32 箱，共 4 層 Seal the outer pack with the adhesive tape on the two side and the middle slot. Then pile them to the underlay orderly. Each pallet should be placed 4 layers, and each layer with 32cartons.口 外箱是否按“工字型”封箱口棧板堆放是否正確產率計算 YIELD RECONCILIATION灌裝Filli ng總數 Total瓶 bottle，半制品損耗量 Bulk waste quantitv.Kg.QA 取樣量 Sampling Quantity灌裝得率 Filling yield%（96.0%）， 計算人 calculate by:復核 check by:.包裝Packagi ng包裝規格 Packaging specification,共箱 Ca