后張法預制t梁鋼絞線張拉伸長量計算書

1、.大中橋明挖基礎施工工藝流程大中橋明挖基礎施工工藝流程大中橋明挖基礎施工工藝流程后 張 法 預 制 T 梁 （30m）鋼絞線張拉伸長量計算書XX高速公路XX標后張法預制T梁鋼絞線張拉伸長量計算XX南互通板梁預制廠位于XX南互通區內，占地23畝。預制廠內設26個后張法T梁臺座，負責生產302片T梁。所有T梁均采用C50砼澆筑。預應力鋼絞線采用GB/T5224-2003標準的高強低松弛15.2mm預應力鋼絞線。鋼絞線標準強度=1860Mpa。所有預應力鋼絞線采用張拉和伸長值雙控張拉施工，張拉控制應力按設計施工圖正彎矩采用=0.73×=0.73×1860 Mpa=1357.8 M

2、pa。根據天津市市政公路材料試驗管理局試驗中心的檢測結果，我部進場的鋼絞線彈性模量為=1.95×105Mpa，單根公稱截面積為Ay=1357.8×103×140×10-6=190.09KN。T梁的張拉施工工藝及計算數據如下。一、 張拉施工工藝及程序：根據公路橋涵施工技術規范和設計圖紙規定，張拉施工控制采用張拉和伸長值雙控方式很圓錨整體張拉、扁錨單根張拉的施工工藝。張拉施工程序如下：低松弛預應力鋼絞線0初應力（持荷兩分鐘）錨固，即用兩個150t千斤頂兩端同時張拉，初應力為的10%，此時的伸長值為，其值采用相鄰級的伸長值?？刂茝埨瓚?yīng)為=0.73×=

3、0.73×1860 Mpa=1357.8 Mpa即為末張的應力值。其中伸長值=，為開始至初張的伸長量，為初張至末張間的伸長量。張拉完畢后，與計算伸長值比較，其伸長值誤差不應超過6%，否則應停止張拉，查明原因。二、 計算參數：1、15.2鋼絞線的彈性模量：=1.95×105Mpa2、15.2鋼絞線的張拉控制應力：正彎矩：=0.73×=0.73×1860 Mpa=1357.8 Mpa3、孔道摩阻系數：=0.254、孔道每米局部偏差對摩擦的影響系數：k=0.0015三、 張拉伸長量計算：1、 計算公式： 式中： P····

4、;·····鋼絞線張拉力 ·········預應力鋼絞線的計算伸長量 L·········預應力鋼絞線的長度·········預應力鋼絞線的彈性模量·········鋼絞線的截面積簡化計算式

5、：·········鋼絞線平均張拉力， ·········預應力鋼絞線的計算伸長量 L·········預應力鋼絞線的長度·········預應力鋼絞線的彈性模量······

6、83;··鋼絞線的截面積2、 張拉伸長量計算表：30米T梁邊跨邊梁鋼束編號孔道長度（米）工作長度（米）鋼絞線根數（根）夾角（rad）（m）正彎矩N129.591.270.12217300.96345370.206866N229.5531.270.11344640.96451870.206836N329.5131.270.11344640.96454730.206566N429.4731.270.11344640.96457590.20630630米T梁邊跨中梁鋼束編號孔道長度（米）工作長度（米）鋼絞線根數（根）夾角（rad）（m）正彎矩N129.591.270.122173

7、00.96345370.206866N229.5531.270.11344640.96451870.206836N329.5131.260.11344640.96454730.206566N429.4731.260.11344640.96457590.20630630米T梁中跨邊梁鋼束編號孔道長度（米）工作長度（米）鋼絞線根數（根）夾角（rad）（m）正彎矩N129.551.270.12217300.96348220.206596N229.511.270.11344640.96454730.206566N329.4731.260.11344640.96457590.206306N429.433

8、1.260.11344640.96457590.20604630米T梁中跨中梁鋼束編號孔道長度（米）工作長度（米）鋼絞線根數（根）夾角（rad）（m）正彎矩N129.551.260.12217300.96348220.206596N229.511.260.11344640.96454730.206566N329.4731.260.11344640.96457590.206306N429.4331.260.11344640.96457590.206046四、預應力T梁控制張拉力計算：1、邊跨邊梁N1、N2、N3、N4，邊跨中梁N1、N2，中跨邊梁N1、N2：FK= ×n×=0

9、.73×1860×103×7×0.140×10-3 =1330.644KN2、邊跨中梁N3、N4，中跨邊梁N3、N4，中跨中梁N1、N2、N3、N4：FK= ×n×=0.73×1860×103×6×0.140×10-3 =1140.552KN五、 張拉數據表：1、 邊跨邊梁N1，邊跨中梁N1正彎矩鋼絞線：分級張拉順序平均張拉力（KN）控制張拉力（KN）張拉控制應力（Mpa）油表讀數伸長量（cm）備注8384858610%張拉力128.20133.06135.784.33.74

10、.24.22.0720%張拉力256.40266.13271.568.57.88.48.44.1440%張拉力512.81532.26543.1216.916.216.816.78.2760%張拉力769.21798.39814.6825.324.525.225.112.4180%張拉力1025.611064.521086.2433.632.933.733.516.55100%張拉力1282.011330.6441357.842.041.242.141.820.692、 邊跨邊梁N2、邊跨中梁N2正彎矩鋼絞線：分級張拉順序平均張拉力（KN）控制張拉力（KN）張拉控制應力（Mpa）油表讀數伸長量

11、（cm）備注8384858610%張拉力128.34133.06135.784.33.74.24.22.0720%張拉力256.69266.13271.568.57.88.48.44.1440%張拉力512.37532.26543.1216.916.216.816.88.2760%張拉力770.06798.39814.6825.324.525.225.112.4180%張拉力1026.741064.521086.2433.632.933.733.516.55100%張拉力1283.431330.6441357.842.141.242.241.920.693、 邊跨邊梁正彎矩鋼絞線（N3）：分級

12、張拉順序平均張拉力（KN）控制張拉力（KN）張拉控制應力（Mpa）油表讀數伸長量（cm）備注8384858610%張拉力128.35133.06135.784.33.74.24.22.0720%張拉力256.69266.13271.568.57.88.48.44.1340%張拉力513.39532.26543.1216.916.216.816.88.2760%張拉力770.08798.39814.6825.324.525.325.112.3980%張拉力1026.781064.521086.2433.732.933.733.516.52100%張拉力1283.471330.6441357.84

13、2.141.242.241.920.664、 邊跨邊梁正彎矩鋼絞線（N4）：分級張拉順序平均張拉力（KN）控制張拉力（KN）張拉控制應力（Mpa）油表讀數伸長量（cm）備注8384858610%張拉力128.35133.06135.784.33.74.24.22.0620%張拉力256.7266.13271.568.57.88.48.44.1340%張拉力513.40532.26543.1216.916.216.816.88.2560%張拉力770.10798.39814.6825.324.525.325.112.3880%張拉力1026.811064.521086.2433.732.933.

14、733.516.50100%張拉力1283.511330.6441357.842.141.342.241.920.635、 邊跨中梁正彎矩鋼絞線（N3）：分級張拉順序平均張拉力（KN）控制張拉力（KN）張拉控制應力（Mpa）油表讀數伸長量（cm）備注8384858610%張拉力110.01114.06135.783.73.13.63.62.0720%張拉力220.02228.11271.567.36.77.27.24.1340%張拉力440.05456.22543.1214.513.814.414.48.2660%張拉力660.07684.33814.6821.721.021.721.512.

15、3980%張拉力880.09912.441086.2428.928.128.928.716.52100%張拉力1100.121140.5521357.836.135.336.135.920.666、 邊跨中梁N4，中跨邊梁N3，中跨中梁N3正彎矩鋼絞線：分級張拉順序平均張拉力（KN）控制張拉力（KN）張拉控制應力（Mpa）油表讀數伸長量（cm）備注8384858610%張拉力110.01114.06135.783.73.13.63.62.0620%張拉力220.03228.11271.567.36.77.27.24.1340%張拉力440.06456.22543.1214.513.814.41

16、4.48.2560%張拉力660.09684.33814.6821.721.021.721.512.3880%張拉力880.12912.441086.2428.928.128.928.716.50100%張拉力1100.151140.5521357.836.135.336.135.920.637、 中跨邊梁正彎矩鋼絞線（N1）：分級張拉順序平均張拉力（KN）控制張拉力（KN）張拉控制應力（Mpa）油表讀數伸長量（cm）備注8384858610%張拉力128.21133.06135.784.33.74.24.22.0720%張拉力256.41266.13271.568.57.88.48.44.1

17、340%張拉力512.82532.26543.1216.916.216.816.78.2660%張拉力769.23798.39814.6825.324.525.325.112.3980%張拉力1025.641064.521086.2433.632.933.733.516.52100%張拉力1282.051330.6441357.842.041.242.141.820.668、 中跨邊梁正彎矩鋼絞線（N2）：分級張拉順序平均張拉力（KN）控制張拉力（KN）張拉控制應力（Mpa）油表讀數伸長量（cm）備注8384858610%張拉力128.35133.06135.784.33.74.24.22.0

18、720%張拉力256.69266.13271.568.57.88.48.44.1340%張拉力513.39532.26543.1216.916.216.816.88.2660%張拉力770.08798.39814.6825.324.525.325.112.3980%張拉力1026.781064.521086.2433.732.933.733.516.52100%張拉力1283.471330.6441357.842.141.242.241.920.669、 中跨邊梁N4,中跨中梁N4正彎矩鋼絞線：分級張拉順序平均張拉力（KN）控制張拉力（KN）張拉控制應力（Mpa）油表讀數伸長量（cm）備注83

19、84858610%張拉力110.01114.06135.783.73.13.63.62.0620%張拉力220.03228.11271.567.36.77.27.24.1340%張拉力440.06456.22543.1214.513.814.414.48.2460%張拉力660.09684.33814.6821.721.021.721.512.3680%張拉力880.12912.441086.2428.928.128.928.716.48100%張拉力1110.151140.5521357.836.135.336.135.920.6010、 中跨中梁正彎矩鋼絞線（N1）：分級張拉順序平均張拉力

20、（KN）控制張拉力（KN）張拉控制應力（Mpa）油表讀數伸長量（cm）備注8384858610%張拉力119.89114.06135.783.73.13.63.62.0720%張拉力219.78228.11271.567.36.67.27.24.1340%張拉力439.56456.22543.1214.513.814.414.48.2660%張拉力659.34684.33814.6821.720.921.621.512.3980%張拉力879.12912.441086.2428.828.128.928.716.52100%張拉力1098.901140.5521357.836.035.336.1

21、35.920.6611、 中跨中梁正彎矩鋼絞線（N2）：分級張拉順序平均張拉力（KN）控制張拉力（KN）張拉控制應力（Mpa）油表讀數伸長量（cm）備注8384858610%張拉力110.01114.06135.783.73.13.63.62.0720%張拉力220.02228.11271.567.36.77.27.24.1340%張拉力440.05456.22543.1214.513.814.414.48.2660%張拉力660.07684.33814.6821.721.021.721.512.3980%張拉力880.09912.441086.2428.928.128.928.716.52100%張拉力1100.121140.5521357.836.135.336.13