ysi水質分析儀 YSI EXO多參數水質分析儀英文操作手冊

1、ysi水質分析儀 YSI EXO多參數水質分析儀英文操作手冊_圖文 導讀：就愛閱讀網友為您分享以下“YSI EXO多參數水質分析儀英文操作手冊_圖文的資訊，希望對您有所幫助，感謝您對92to 的支持!Sonde Replace EXO1 Bail Sonde bails provide users with a handle for convenient transport and an attachment point for cable strain reliefs. If an EXO1 bail breaks due to impact or standard wear and tea

2、r throughout the life of the sonde, a user can easily replace it. We also recommend attaching the cables strain relief mechanism to the bail. 1 Remove battery cover. Twist the battery cover counterclockwise until free. Then slide off the battery cover. 2 Remove bail. Spread the sides of the bail awa

3、y from the connector, pull the bail over the posts on top of the sonde, and remove the o-ring from its groove and discard. 3 Install new bail. Install a new o-ring in the groove at the base of the bail. Then carefully spread the bail open and seat its sockets over the posts around the connector. pg

4、|109 Sonde Replace EXO2 Bail Sonde bails provide users with a handle for convenient transport and an attachment point for cable strain reliefs. If an EXO2 bail breaks due to impact or standard wear and tear throughout the life of the sonde, a user can easily replace it. We also recommend attaching t

5、he cables strain relief mechanism to the bail. 1 Remove bail. Use a small screwdriver to remove two screws on the sides of the bail. Once screws are removed, lift the bail off the sonde.2 Install new bail. Place the new bail onto the sonde, aligning holes for the screws. With one side of the bail al

6、igned, push on the other side to snap it into place. Use a small screwdriver to insert two screws on the sides of the bail. Tighten until snug. Sonde Update Firmware & KOR Software Users can check for and download new versions of KOR software through the EXOwater website. Click on Support an

7、d then the Software tab for the latest information and complete installation instructions. Users can check and update sensor or sonde firmware through the KOR interface software. Each device must be connected to the computer that is running the Desktop version of KOR, and the computer must have inte

8、rnet access. This process may take up to 30 minutes depending on the number of sensors updated. 1 Open firmware submenu in KOR. Navigate to the Options menu in KOR, then to the Firmware submenu. Immediately after clicking the Firmware submenu button, KOR begins to search for connected sondes and sen

9、sors and loads the table with names, serial numbers, and current firmware versions. 2 Select device and update. To update a device, click on the devices name in the table and then click the Update Selected button. KOR then updates the devices firmware, which could take several minutes. To update all

10、 connected devices (i.e., attached sonde and senors), click the Update Network button. NOTE: For best power management, update firmware while a device is connected via USB, as this will provide power to the device. However, if you use Bluetooth, we recommend installing fully charged batteries in the

11、 sonde. See section 6.11 for instructions on how to update sonde and sensor firmware using the EXO Handheld when the sonde is in the field. pg |111 Handheld Maintenance and Storage EXO Handhelds (HH) are rugged field instruments that are tested to a rating of IP-67 in the factory. Follow the instruc

12、tions below for the most reliable performance from the HH. This section will identify storage as “l(fā)ong-term or “short-term. Long-term denotes storage during times of long inactivity (over winter, end of monitoring season, etc.). Short-term denotes storage during times the sonde will be used at a reg

13、ular interval (daily, weekly, biweekly, etc.). pg |1121 Clean handheld.If the HHs USB connector is contaminated, rinse it with clean water and dry it. To clean the HHs cable connector, follow directions in section 6.24 for Connector Maintenance.Wipe clean the HHs keypad, lens, and polymer case with

14、a cloth soaked in clean water and a few drops of a dishwashing liquid that contains a degreaser. Take care not to scratch the lens. 2 Short-term storage. Keep the HH in a safe storage location and power it down by pressing and holding the power buttonthree seconds. Pressing the power button for more

15、 than seconds does not entirely power down the instrument for less than three (Sleep mode) and may cause unnecessary battery drain. 3 Long-term storage.Keep the HH in a safe location and remove the batteries (and reinstall the battery compartment panel) to prevent potentially harmful battery leaks.N

16、OTE: If the HH is stored for more than several days without batteries, the GPS will take longer to obtain a location fix.EXO User Manual ADVANCED WATER QUALITY MONITORING PLATFORM Item# 603789REFRevision D THIS IS AN INTERACTIVE DOCUMENT When viewing this document as an Adobe PDF, hovering your cursor over certain phrases will bring up the finger-point icon. Clicking elements of the Table of Contents, website URLs, or references asking you to see a certain section will take automatically to those locations. No scrolling required! The information contained in this manual is subject to