鋼絲螺套安裝使用說明

經典word整理文檔，僅參考，轉Word此處可刪除頁眉頁腳。本資料屬于網絡整理，如有侵權，請聯系刪除，謝謝！可供選擇的公稱長度minmax1D1.5D2.5D3D3.825.126.327.627X18.728X19.8210.0410.3412.3612.5012.8014.9615.2017.2019.5219.9021.8224.1624.2026.5228.9229.0029.1032.6432.5636.3636.1235.7540.1839.7410.0612.0812.1012.5214.6814.9616.9219.1819.4021.4823.8223.7026.0028.4028.5028.6032.0231.9435.7435.5035.2039.5639.1230X1.530X230X3.533X1.533X242.1045.1052.5055.1742.6045.6053.5056.0745X1.548X3絲套圈數（）2X0.42.6-2.812.259.62.5X0.453.2-3.4511.113.63.82-4.005.15-5.356.35-6.68.711.013.588.411.013.29.769ZST6X11215186.37.6-7.859.62.5d3d12.314.681216209.85-10.110.613.52.5d3d2416.412.1-12.412.1-12.514.2-14.514.4-14.813.411.214.217.27.411.615.911.714.718.08.417.2-17.417.2-17.717.2.17.77.111.215.311.5ZST16X219.4-19.92.5dZST18X1.521.5-222736621.84-22.2423.7-24.29.512.81d1.5d2d20304010.716.722.46.323.7-24.226.3-26.81d1.5dZST24X1.524.528.6-29.16.328.6-29.132.2-32.732.2-32.735.2-35.71.5d40.58.027X21.5d40.5730X3.51114.91d3641.2-41.945.10-45.6052.50-53.5055.17-56.0720鋼絲螺套安裝使用方法主要包括以下四個環節：一、鉆孔二、攻牙三、安裝四、去尾柄四個步驟。要求嚴格的鋼絲螺套安裝步驟還需在第二步攻牙以后，用專用鋼絲螺套底孔塞規對攻好牙的底孔進行檢測，通規能通，止規能止的狀態下才能進行下一步鋼絲螺套安裝操作。此外對安裝不好的鋼絲螺套可采用專用取套工具—卸套器將其取出。1鉆孔鋼絲螺套安裝步驟第一步---鉆孔使用表中所列的標準鉆頭鉆孔,,切屑不要掉入。鉆孔后锪孔不應超過0.4螺距深度,因為锪孔過大不利于鋼絲螺套的旋入。使用表中所列的標準鉆頭鉆孔,,切屑不要掉入。鉆孔后锪孔不應超過0.4螺距深度,因為锪孔過大不利于鋼絲螺套的旋入。螺紋規格M8x1M10x110.3M10x1.25M12x1.25M12x1.5M12x110.312.312.412.3M7x1M13x1.25M14x1.5M14x1.25M16x1.5M18x1.5M20x1.5M20x213.3M8x1.25M10x1.5M11x1.5M12x1.75M14x214.410.411.412.414.516.518.620.6