鋼板樁圍堰設計計算

PAGEPAGE3鋼板樁圍堰設計計算一、土層地質情況根據設計圖紙?zhí)峁┑膮?shù)，設計洪水位為+5.40M，12#墩河床高程為-2.00M,土層地質為淤泥質粉質粘土，土性質為：為16.5KN/M3，φ取9.50，C取12.3KPa。二、支撐布置圍堰中共設三道支撐，第一點支撐標高為+3.19M，第二支撐標高為+1.19M，第三道支撐標高為-2.41M,采用H40型鋼進行支撐。以φ400的鋼管進行斜支撐。支撐圖紙如下圖：支撐布置圖（單位：M）三、體系簡化驗算：主動土壓力系數：Ka=tg2(450-9.50/2)=0.717土壓力：取浮=9N/M3Ea=1/2KaH22=1/2×0.717×9×5.6252=102.088KN/M水壓力：純水w水=1/2ρg(H1+H2)2=1/2×10×(7.4+5.625)2=848.253KN/M總壓力：Ea+E水=102.088+848.253=950.341KN/M壓力計算圖（單位：M）四、應力計算R1=1/2×10×(5.4-3.19)2=24.42KN/MR2=1/2×10×(5.4+0.61)2-24.42=156.18-24.42=131.76KN/MR3=1/2×10×(5.4+5.018)2-156.18+1/2×0.717×(5.018-2)2×9=415.882KN/MR4=1/2×10×(5.4+7.625)2-542.674+1/2×0.717×9(7.625-2)2-29.388=378.284KN/M鋼板樁驗算采用拉森Ⅳ型，寬40cm，截面系數Wx=2270cm3R1=24.42×0.4=9.768KNR2=131.76×0.4=52.704KNR3=415.882×0.4=166.353KNR4=378.284×0.4=151.314KNN=1/2qH=1/2×0.4×9.8×H×H=1/2×3.92×H×H即q=3.92×HME=0MD=-1/2×10×(5.4-3.19)2×1/3×2.21×0.4=-7.196KN.MMC=9.768×2-1/6×10×4.213×0.4=-30.21KN.MMB=9.768×5.6+52.704×3.6-1/6×10×7.813×0.4-1/6×0.717×9(2.41-2)3×0.4=-73.18MA=9.768×10.815+52.704×8.815+166.353×5.215-1/6×10×0.4×13.0253-1/6×0.717×0.4×9(7.625-2)3=-111.942KN.MMDC中點=9.768×1-1/6×10×3.213×0.4=12.283KN.MMCB中點=9.768×3.8+52.704×1.8-1/6×10×6.013×0.4=54.9KN.MMBA中點=9.768×8.208+52.704×6.208+166.353×2.608-1/6×10×10.4183×0.4-1/6×0.717×9×3.0183×0.4=75.574KN.M根據計算結果繪制彎矩圖如下：Max=111.942KN.M查表得鋼板樁[σ]=180MPa截面模量w=2270cm3σ=111942/2270=49.3MPa<[σ]=180MPa滿足要求！六、基坑底的安全驗算按圍堰施工至封底混凝土人頂標高-7.625根據公式>Kj取安全系數K=1.5土的浮容重=16.5-10=8.0KN/M3最大滲流力j=iwi=h/(h+2t)=(5.4+7.625)/(5.4+7.625+2t)=13.025/(13.025+2t)t為鋼板樁底部到開挖面的距離所以j=iw=10×13.025/(13.025+2t)≥Kj≥1.5×130.25/(13.025+2t)t≥5.7Mt實施過程中取值為6.5M，大于5.7M，滿足要求！根據上面計算設計的鋼板樁圍堰基坑底滿足安全方面要求。支撐設置及安全驗算：第一道支撐設置及計算：最大受力狀態為圍堰外水位為+5.4M，堰內抽水至第二道支承下50cm，即0.69M時，作為計算考慮。水壓力w水=1/2×10×（5.4-0.69）2=110.92KN/Mw=110.92KN/MQA=QB=0.4ql即RA=RD=0.4×36.97×4=59.152KNRB=RC=(36.97×12-59.152×2)/2=162.668KNN直=RA+2RB=384.488KNN斜=2RB=325.336KN直撐驗算：單根H40,Iy=22400iy=10.1截面積219.5cm2寬b=40M組合截面Jy=2[22400+21915×202]=220400cm4iy=22.4cmλ=ul/I=1×400/22.4=17.85查表得φ1=0.783k=1.4[kσ]=0.783×180=140.94MPa則σ=1.4×384.488×103/0.783×2×219.5×10-4=15.66MPa<[σ]=140.94MPa滿足要求！斜支撐驗算：φ1=0.635k=1.4采用50×50×1cm鋼板σ=1.4×302.37×103/0.635×2×50×50×10-4=1.33MPa<[σ]，滿足要求！彎矩驗算：Mmax=-0.1×ql2=-0.1×36.97×42=59.152KN.Mσ=1.4Mmax/w=59.152×1.4×103/2×1073.349×10-6=38.58MPa<[σ]，滿足要求！第二道支撐設置及計算：計算狀況：水位5.4M堰內抽水到-2.91M以準備焊接第三道支撐R2=1/2×10×(5.4+0.86)2-1/2×10×(5.4-3.19)2=171.52KN/MQA=QB=0.4ql即RA=RD=0.4×51.17×4=91.484KNRB=RC=(91.48×12-2×171.52)×1/2=377.36KN直撐軸力：N直=RA+1.414RB=625.07MPaN斜=1.414RB=533.59MPa直撐驗算：單根H40,Iy=22400iy=10.1截面積219.5cm2寬b=40M組合截面Jy=2[22400+21915×202]=220400cm4iy=22.4cmλ=ul/I=1×400/22.4=17.85查表取φ=0.783k取1.4[σk]=0.783×180=140.94MPaσ=KN/ΦA(chǔ)m=1.4×625.07×10-3/0.783×219.5×10-4=50.92MPa<[σ]，滿足要求！斜撐驗算：查表φ=0.635k取1.4采用50×50×1cm鋼板σ=KN/φAm=