計量型MSA計算模板-自動計算公式

XXX有限公司,,,,,,,,,,,,

量具重復性和再現性數據表,,,,,,,,,,,,

產品名稱：,3031275,,,,量具名稱：,,千分尺,,量具編號：,,QFC-36,

被測參數：,C/H,,,,測量范圍：,,0~25mm,,量具精度：,,0.001mm,

測量者/量測次數,,,零,,,,件,,,,平均值,

,1,2,3,4,5,6,7,8,9,10,,

A1,1.120,1.178,1.132,1.145,1.152,1.154,1.162,1.164,1.176,1.170,,1.155

A2,1.120,1.179,1.135,1.149,1.153,1.152,1.160,1.165,1.171,1.171,,1.156

A3,1.122,1.180,1.133,1.146,1.151,1.156,1.159,1.163,1.175,1.173,,1.156

平均值,1.121,1.179,1.133,1.147,1.152,1.154,1.160,1.164,1.174,1.171,Xa=,1.1555

極差,0.002,0.002,0.003,0.004,0.002,0.004,0.003,0.002,0.005,0.003,Ra=,0.0030

B1,1.123,1.180,1.130,1.142,1.151,1.154,1.162,1.166,1.174,1.170,,1.155

B2,1.123,1.180,1.134,1.145,1.150,1.157,1.160,1.164,1.176,1.172,,1.156

B3,1.121,1.181,1.132,1.148,1.150,1.152,1.159,1.163,1.171,1.171,,1.155

平均值,1.122,1.180,1.132,1.145,1.150,1.154,1.160,1.164,1.174,1.171,Xb=,1.1554

極差,0.002,0.001,0.004,0.006,0.001,0.005,0.003,0.003,0.005,0.002,Rb=,0.0032

C1,1.120,1.179,1.131,1.145,1.150,1.153,1.165,1.165,1.172,1.170,,1.155

C2,1.123,1.180,1.130,1.147,1.150,1.152,1.160,1.166,1.176,1.170,,1.155

C3,1.121,1.181,1.132,1.149,1.151,1.156,1.159,1.163,1.171,1.171,,1.155

平均值,1.121,1.180,1.131,1.147,1.150,1.154,1.161,1.165,1.173,1.170,Xc=,1.1553

極差,0.003,0.002,0.002,0.004,0.001,0.004,0.006,0.003,0.005,0.001,Rc=,0.0031

零件,,,,,,,,,,,Rp=MaxXp-MinXp,

平均值,1.121,1.180,1.132,1.146,1.151,1.154,1.161,1.164,1.174,1.171,Rp=,0.0583

(Xp),,,,,,,,,,,X=CLX,1.155

R=Ra+Rb+Rc/作業者人數,,,R=,0.0031,,XDIFF=MaxX-MinX,,,,,XDIFF=,0.0003

UCLX=X+A2R,,,UCLX=,1.159,,LCLX=X-A2R,,,,,LCLX=,1.152

UclR=R×D4*,,,UCLR=,0.0080,,LclR=R×D3*,,,,,LCLR=,0

"兩次試驗D4=3.27、A2=1.88,三次試驗D4=2.58、A2=1.02.UCLR代表單個R的值,圈出那些",,,,,,,,,,,,

"超限值的值,識別原因并糾正,同一作業者采用最初的儀器重復這些讀數或者剔除這些超限值,剩余",,,,,,,,,,,,

觀察值再次平均并計算R和控制限值。,,,,,,,,,,,,

,,,,,,,,,,,,,

測量者A：,,,,測量者B：,,,,,測量者C：,,,

,,,,,,,,,,,,,

,,,,,,,,,,,,,

,,,,,,,,,,,,,

,,,,,,,,,,,,,

,,,,,,,,,,,,,

,,,,,,,,,,,