加拿大ULC阻燃、防火測試標準

1、加拿大ULC阻燃、防火測試標準CAN/ULC-S101-M89 :建筑結構和材料的耐火性測試方法CAN/ULC-S101-M89 : Sta ndard Methods of Fire En dura nee Tests of Buildi ng Con structio nand MaterialsAbstract 摘要This Stan dard covers fire en dura nee tests applicable to walls, partiti ons, floors, roofs, ceili ngs, colu mns, beams, and girders, as

2、well as to some comp onents of these buildi ng sub-assemblies. It is the intent that the fire en dura nee period established by this test method indicates performanee only during the fire exposure period and shall not be con strued as havi ng determ ined suitability for use after fire exposure.CAN/U

3、LC-S102-M88:建筑材料和配件表面燃燒特性測試方法CAN/ULC-S102-M88 : Standard Method of Test for Surface Burning Characteristics of Build ing Materials and AssembliesAbstract 摘要This method of test for surface burning characteristics of building materials is applicable to any type of building material that, by its own st

4、ructural qualities or the manner in which it is applied, is capable of support ing itself in positi on or may be supported in the test furn ace as described in this Stan dard or in a manner comparable to its recomme nded use.Where a material cannot be readily determ ined to be thermoplastic or therm

5、oset, one test is con ducted in accorda nee with this Stan dard and one additi onal test in con forma nee with requireme nts of CAN/ULC-S102.2, Sta ndard Method of Test for Surface Burni ng Characteristics of Floori ng, Floor Coveri ngs, and Miscella neous Materials and Assemblies.The primary purpos

6、e of this test is to determ ine the comparative burning characteristics of the material or assembly un der test by evaluati ng the flame spread over its surface whe n exposed to a test fire and thus establish a basis on which surface burning characteristics of differe nt materials or assemblies may

7、be compared, without specificcon siderati ons ofall the end use parameters that might affect these characteristics.It is the intent of this method to register performanee during the period of exposure, and not to determ ine suitability for use after the test exposure.CAN/ULC-S102.2-M88 :地板，地面覆蓋物和復合材

8、料及配件表面燃燒特性測試方法CAN/ULC-S102.2-M88: Standard Method of Test for Surface Burning Characteristics ofFloori ng, Floor Coveri ng, and Miscella neousMaterials andAssembliesAbstract 摘要The primary purpose of the Standardis to determinethe comparative burning characteristics of the material or assembly un der

9、 test by evaluat ing the flame spread over its surface whe n exposed to a test fire and thus establish a basis on which surface burning characteristics of different materials or assemblies may be compared, without specific con siderati ons of all the en d-use parameters that might affect these chara

10、cteristics.ULC-S102.3-M1982:光散射器和鏡頭的防火測試方法ULC-S102.3-M1982: Standard Method of Fire Test of Light Diffusers and LensesAbstract 摘要This test method is applicable to materials employed in light diffusers and len ses.The testi ng procedure described here in is inten ded to assess the prope nsity of mate

11、rial employed in light diffusers and len ses to fall from its in stalled positi on before ign it ing whe n subjected to test fire exposure con diti ons in CAN/ULC-S102.以上資料由防火資源網( )防火測試中心整理或發布。ULC-S102.4-M1987:電線電纜的燃燒及煙霧特征防火測試方法ULC-S102.4-M1987:Standard Method of Test for Fire and Smoke Characterist

12、ics of Electrical Wiring and CablesAbstract 摘要This test is designed to provide information for evaluating the possibility of fire spreading in a plenum or other space used for environmental air along electrical wires or cables, optical-fiber cables or non-metallic raceways; or the possibility of hig

13、h smoke levels being developed in the space whe n wiri ng or raceways are subject to fire exposure. The test method has bee n related to the results of tests on cables exposed to fires in simulated ple nu ms.This test method is used to determine if a cable or non-metallic raceway qualifies for an FT

14、-6classification as specified in CSA C22.2 No. 0.3, Test Methods for Electrical Wires and Cables or CSA C22.2 No. 262, Optical Fiber Cable and Communication Cable Raceway Systems.This test method is for use in determ ining values of flame propagati on dista nee and smoke optical den sity for electri

15、cal and optical-fiber cables and non-metallic raceways that are to be in stalled in ducts, ple nu ms, and other spaces used for environmen tal air. It is not inten ded for use with cables en closed in metallic raceways in those spaces. This method also determ ines values of flame propagatio n dista

16、nee and smoke optical den sity for electrical and optical-fiber cables with combustible jackets or sheathes, and non-metallic raceways to determ ine their acceptability for use in buildi ngs of non-combustible con struct ion.This test method does n ot cover the con struct ion requireme nts for cable

17、s and non-metallic raceways or their electrical and other performa nee requireme nts.CAN4-S104-M80:房門附件的防火測試CAN4-S104-M80: Standard Method for Fire Tests of Door AssembliesAbstract 摘要This fire test method is applicable to door assemblies (comprising doors, frame products, hardware, glaz ing material

18、s, and other parts, accessories or comp onen ts) of various materials and types of con struct ion, for use in wall ope nings to retard the passage of fire. This test method is also applicable for evaluati ng in dividual comp onents (doors, frame products, hardware, glaz ing materials, light kits, lo

19、uvers and other parts or accessories) inten ded as part of a fire test assembly.Wood core doors meet ing the requireme nts of CAN/ULC-S113, Stan dard Specificati on for Wood Core Doors Meeti ng the Performa nee Required by CAN/ULC-S104 for Twenty Mi nute Fire Rated Closure Assemblies, and frames mee

20、t ing the requireme nts of CAN/ULC-S105, Sta ndard Specificati on for Fire Door Frames Meeti ng the Performa nee required by CAN/ULC-S104, are not required to be tested to the requireme nts of this Stan dard. However, doors and frames meet ing these specificati ons may be used for the evaluati on of

21、 in dividual comp onen ts.It is the intent that tests made in con formity with this test method will develop data to en able regulatory bodies to determ ine the suitability of door assemblies for use in locati ons where fire protect ion of a specified durati on is required.CAN4-S106-M80 :窗戶和玻璃配件耐火件的

22、防火測試方法CAN4-S106-M80: Standard Method for Fire T ests of Window and Glass Block AssembliesAbstract 摘要These requirements apply to window and glass block assemblies and other light transmitting assemblies, for use in walls and partitions that are fire separations. Tests made in conformity with this tes

23、t method will register performanee during the test exposure and develop data to enable regulatory bodies to determine the suitability of window assemblies for use in wall and partition openings where fire protection is required.Such tests shall not be construed as determining suitability of window a

24、ssemblies for con ti nued use after fire exposure.以上資料由防火資源網( )防火測試中心整理或發布。CAN/ULC-S107-M87 :屋頂覆蓋材料的防火測試方法Abstract 摘要The test methods described in this Standard are applicable to roof covering materials and are intended to measure the relative fire-performanee characteristics of roof coverings when

25、exposed to fire originating from sources outside a building on which they may be in stalled. They are applicable to roof coveri ngs inten dedfor in stallati onon eithercombustible or non-combustible decks whe n applied as inten ded for use.CAN/ULC-S109-M87 :阻燃纖維和薄膜的易燃性測試方法CAN/ULC-S109-M87 : Standard

26、 for Flame Tests of Flame-Resistant Fabrics and FilmsAbstract 摘要These requireme nts apply to the performa nee in flame-exposure tests of flame-resista nt fabrics of n atural, syn thetic, or comb in ati ons of n atural and syn thetic fibres, or plastic films intended for such use as tents, awnings, d

27、raperies, or decorations. The flame resistance of the fabric or film may be in here nt in the material used or may be the result of chemical treatment to retard ignition and spread of flame.These requirements are not intended to apply to fabrics and films to be used for clothing nor to materials to

28、be applied to surfaces of building or backing materials as interior fini shes.CAN/ULC-S110-M86 :通風管道防火測試方法CAN/ULC-S110-M86 : Standard Methods of Test for Air DuctsAbstract 摘要These requirements apply to materials for the fabrication of air duct systems for use in accorda nce with the requireme nts of

29、 the curre nt editi on of the Nati onal Buildi ng Code. The materials covered by these requireme nts in clude preformed len gths of flexible or rigid ducts, materials in the form of boards for field fabrication of lengths of rigid ducts, and preformed flexible conn ectors.ULC-S111-95 :空氣過濾裝置的防火測試方法U

30、LC-S111-95 : Standard Method of Fire Tests for Air Filter UnitsAbstract 摘要These requireme nts cover air filter un its of both washable and throw-away types for removal of dust and other airbor ne particles from air circulated mecha ni cally in equipme nt and systems.CAN/ULC-S112-M90:消防阻尼配件的防火測試方法CAN

31、/ULC-S112-M90 : Standard Method of Fire Test of Fire-Damper AssembliesAbstract 摘要TiretcjcniM一防火盜源網These requireme nts and methods of test apply to fire damper assemblies rated ? h, 1 h,1? h, 2 h, or 3 h for use in air-conditioning and ventilating system ducts or openings (without ducts) pierci ng ho

32、riz on tally or vertically orie nted fire separati ons where the fire separati ons are required to have a fire resista nee rat ing of not more tha n 4 h.It is the intent that tests made in con formity with these test methods will develop data to en able regulatory bodies to determ ine the suitabilit

33、y of damper assemblies for use in locati ons where fire resista nee of a specified durati on is required.ULC-CAN4-S114-M80:建筑材料的不燃性測試評定方法ULC-CAN4-S114-M80: Sta ndard Method of T est for Determ in ation of Non-Combustibilityin Building MaterialsAbstract 摘要This Stan dard provides a means of determ ini

34、ng the non-combustible n ature of eleme ntary buildi ng materials. It shall be applied to materials used in the con struct ion of buildi ngs. It does not apply to materials with a decorative or protective coati ng, or impreg nati on, or built up of lam in atio ns of dissimilar materials.ULC-CAN4-S11

35、5-M85:阻燃系統的防火測試方法ULC-CAN4-S115-M85: Standard Method of Fire Tests of Fire-stop SystemsAbstract 摘要This method of test is applicable to firestop systems with or without penetrating items. These firestop systems are intended for use in openings in fire resistive wall and floor assemblies and membra nes

36、 formi ng part of an assembly required to have a fire resista nee rati ng and lin ear ope nings betwee n adjace nt fire resistive floor assemblies, wall assemblies or both.ULC-CAN4-S117.1-M85:紡織地面材料烏洛托品測試-阻燃測試方法ULC-CAN4-S117.1-M85: Sta ndard Method of Test for Flame Resista nee - Methe nami neTablet

37、 Test for Textile Floor Coveri ngsAbstract 摘要This method determ ines the flammability of fini shed textile floor coveri ng materials whe n exposed to an ignition source (methenamine tablet) under specified conditions. It is applicable to all types of textile floor coverings regardless of fibre type

38、or method of con struct ion. This method describes the testi ng of a sin gle specime n and is to be used in conjunction with a statistically valid sampling plan based on a minimum of ten specimens.Note: Un der the Hazardous Products Act requireme nts for soft floor coveri ngs, the nu mber of specime

39、 ns to be tested is based on the Sta ndard CAN/CGSB-4.155M, Flammability of Soft Floor Coveri ngs - Sampli ng Pla ns.ULC-CAN4-S124-M85 :塑料泡沫保護層評估測試方法ULC-CAN4-S124-M85: StandardMethod of Test for the Evaluation of ProtectiveCoveri ngs for Foamed PlasticAbstract 摘要The purpose of the test is to evaluat

40、e the temperature transmissionperformanee of aprotective eoveri ng over foamed plastic whe n the assembly is subjected to a sta ndard fire exposure condition following the standard time-temperature curve. These protective coveri ngs are com mon ly referred to in the Natio nal Buildi ng Code as therm

41、al barriers. It is the intent that classificati ons shall register performa nee duri ng a period of exposure and shall not be con strued as determ ining suitability for use after fire exposure.以上資料由防火資源網（ ）防火測試中心整理或發布。ULC / CAN4-S126-M86:屋頂下附屬物的火焰?zhèn)鞑y試方法ULC / CAN4-S126-M86Standard Method of Test for

42、Fire Spread under Roof-DeckAssembliesAbstract 摘要This test method provides a means of measuri ng the con tributi on of roof-deck assemblycomponents to the spread of fire on the underside of the roof deck. This method also provides for the assessment of the extent of thermal degradation and charring o

43、f the assembly. The accepta nee criteria in voked in this Stan dard are based on correlative data developed in large scale, 30.5 by 6.0 m building, and tunnel furnace testing of representative field constructions. Where the acceptanee criteria are judged not to be applicable for the con struct ion u

44、n der evaluati on (i.e. the deck con struct ions are markedly different from those described in the Standard), the large scale test or a series of small scale tests, represe ntative of fire exposure con diti ons related to the large scale test, are to be con ducted to establish corresp ondin gly sui

45、table acceptable criteria.ULC-S127-M1988 :非熔性建筑材料的易燃性測試(室角法) ULC-S127-M1988: Standard Corner Wall Method of Test for Flammability Characteristicsof Non-Melting Building MaterialsAbstract 摘要This method of test for flammability characteristics is applicable to certain low density insulating materials

46、that do not melt or drip during exposure to fire (see Appendix A). It is used in establishing the Flame Spread Classification for those foamed plastics whose flammability assessme nt by CAN/ULC-S102 requires the use of the rate formula FSV = 92.5 d/t but where the n ecessary parameters ('d'

47、& 't') for use in the formula are difficult to defi ne.ULC-S129-95 :松散填充絕緣材料阻燃性能測試(BasketULC-S129-95 : Sta ndard Method of Test for Smoulder Resista nee of In sulationAbstract 摘要This Stan dard applies to thermal in sulati on suitable for in door use in buildi ng con struct ion within the

48、 temperature range of -50 to 80C. The types of insulation materials which lendthemselves to the evaluation using the method described in this Standard are: A) Loose fill, designed for pouring application; B)Loose fill, designed for blowing application with the aid of pn eumatic equipme nt; C) Preformed products such as batts, roll boards and sheets;and D) Spray applied products.CAN/UIC-S130-M87:松散填充絕緣材料引燃性能測試CAN/UIC-S130-M87 : Sta ndard Method of Test for Ign itio n Resista nee of Loose Fill In sulatio n (Cigarette