汽車詞匯匯總課件

1、輪椅升降機 Wheel chair lift 圖例 legend 工位 station 吊運裝置 overhead hoist 更衣室 restroom 合籠 mate 底盤平移臺 chassis shuttle 車輛轉移臺 bus transfer 前圍角板 front wall angle cover 后圍側板 rear wall side cover 保險杠 bumper 三類底盤 three type chassis 左側圍應力蒙皮 R/S stretching skin (road side) 中涂 floating coat 拼裝臺 collector 切割輪口 wheel -ar

2、ch cutting 內飾 trim 線束 harness 返工 re-doing 輪罩護板 wheel house 發車前準備 pre-delivery 舉升 hoist 小批量產品 be pilot 配電站 power transformer substation 裙板 skirt 發動機托架 engine holding frame 診斷報警系統 diagnosis and alarming system 互換性 interchangeability 縮微圖紙 microfiche files 總裝 final assembly 磷化 phosphating 儀表板 dash board

3、 切齊 trimming 結構完整性 structure integrity 長途客車 inter-city bus 改裝廠 refitting factory 遮陽板 sun visor 隨車工具 tool box 鋼化玻璃 toughened grass 異形鋼管 special steel pipe 全天候空調系統 full range A/C 強制通風 ram-air ventilation 停機時間 downtime 無公害柴油 clean diesel 寬敞懸臂式座椅 roomy cantilevered seat 防滑地板 no-skid floor 織物紋里鋁合金 textur

4、ed aluminum extrution 爬坡能力 grade ability 排水閥 drain valve 除濕器 moisture ejector 怠速時 at idle 琴式驅動橋 banjo type drive axle 通風口 duct 恒溫控制 thermostatic control 平衡水箱 surge tank 變光開關 simmer switch 消音器 muffler 防破壞 vandal resistant 聚碳化透鏡 poly-carbonate len 鍍鋅板 galvanized plate 搭接 lap 亮麗的外表 smart apperance 隱藏式固

5、定 concealed fastening 水洼 ponding 發動機中置式客車 bus with under floor engine 組合式客車車身 modular bus body 薄殼式結構 shell construction 襯墊 pad 空氣導流板 air deflector 擱梁 shelf beam 腰梁 waist rail 梭梁 stabilizing beam 腰帶式安全帶 diagonal safety belt 壓條 trim strip 嵌條 insertion strip 翼板 fender 斜撐 bracing piece 轉向盤回正性試驗 test of

6、steering wheel returnability 轉向盤轉角脈沖試驗 steering wheel impulse input test 轉向盤轉角階躍輸入試驗 steering wheel step input or transient state yaw response test 極限側向加速度試驗 limiting lateral acceleration test 汽車平順性隨機輸入行駛試驗 automobile ride random input running test 汽車平順性單脈沖輸入行駛試驗 automobile ride single pulse input r

7、unning test 汽車懸掛系統固有頻率與阻尼比的測定試驗 measurement of natural frequency and damping raito of suspension 功率突然變化影響試驗 test of effect of sudden power change 收油門后控制試驗 test of control at breakway 橫風穩定性試驗 test of crosswind stability 反沖試驗 kick-back test 輪胎爆破響應時間試驗 test of burst response of tyre 繞過障礙物試驗 obstacle av

8、oidance test 移線試驗 lane change test J型轉彎試驗 test of J turn 頻率響應時間試驗 frequency response test 瞬態響應時間試驗 transient response test 階路響應時間試驗 step response test 脈沖響應試驗 pulse response test 靜態操舵力試驗 static steering effort test 懸架舉升試驗 jack-up test of suspension 耐翻傾試驗 test of overturning immunity 輪輞錯動試驗 rim slip t

9、est 風洞試驗 wind tunnel test 制動穩定性試驗 test of braking stability 最小轉彎直徑試驗 minimum turning diameter test 操舵力試驗 steering effort test 汽車發動機 類型 type 發動機 engine 內燃機 intenal combusiton engine 動力機裝置 power unit 汽油機 gasoline engine 汽油噴射式汽油機 gasoline-injection engine 火花點火式發動機 spark ignition engine 壓燃式發動機 compressi

10、on ignition engine 往復式內燃機 reciprocating internal combustion engine 化油器式發動機 carburetor engine 柴油機 diesel engine 轉子發動機 rotary engine 旋輪線轉子發動機 rotary trochoidal engine 二沖程發動機 two-stroke engine 四沖程發動機 four-stroke engine 直接噴射式柴油機 direct injection engine 間接噴射式柴油機 indirect injection engine 增壓式發動機 superchar

11、ged engine 風冷式發動機 air-cooled engine 油冷式發動機 oil-cooled engine 水冷式發動機 water-cooled engine 自然進氣式發動機 naturally aspirated engine 煤氣機 gas engine 液化石油氣發動機 liquified petroleum gas engine 柴油煤氣機 diesel gas engine 多種燃料發動機 multifuel engine 石油發動機 hydrocarbon engine 雙燃料發動機 duel fuel engine 熱球式發動機 hot bulb engine

12、多氣缸發動機 multiple cylinder engine 對置活塞發動機 opposed piston engine 對置氣缸式發動機 opposed-cylinder engine 十字頭型發動機 cross head engine 直列式發動機 in-line engine 星型發動機 radial engine 筒狀活塞發動機 trunk-piston engine 斯特林發動機 stirling engine 套閥式發動機 knight engine 氣孔掃氣式發動機 port-scavenged engine 傾斜式發動機 slant engine 前置式發動機 front-e

13、ngine 后置式發動機 rear-engine 中置式發動機 central engine 左側發動機 left-hand engine 右側發動機 right-hand engine 短沖程發動機 oversquare engine 長沖程發動機 undersquare engine 等徑程發動機 square engine 頂置凸輪軸發動機 overhead camshaft engine 雙頂置凸輪軸發動機 dual overhead camshaft engine V形發動機 V-engine 頂置氣門發動機 valve in-head engine 側置氣門發動機 side val

14、ve engine 無氣門發動機 valveless engine 多氣門發動機 multi-valve engine 臥式發動機 horizontal engine 斜置式發動機 inclined engine 立式發動機 vertical engine W形發動機 w-engine I形發動機 I-engine L形發動機 L-engine F形發動機 F-engine 性能 performance 二沖程循環 two-stroke cycle 四沖程循環 four-stroke cycle 狄塞爾循環 diesel cycle 奧托循環 otto cycle 混合循環 mixed cyc

15、le 定容循環 constant volume cycle 工作循環 working cycle 等壓循環 constant pressure cycle 理想循環 ideal cycle 熱力循環 thermodynamic cycle 沖程 stroke 活塞行程 piston stroke 長行程 long stroke 上行程 up stroke 下行程 down stroke 進氣行程 intake stroke 充氣行程 charging stroke 壓縮行程 compression stroke 爆炸行程 explosion stroke 膨脹行程 expansion stro

16、ke 動力行程 power stroke 排氣行程 exhaust stroke 膨脹換氣行程 expansion-exchange stroke 換氣壓縮行程 exchange-compression stroke 止點 dead center 上止點 top dead center(upper dead center) 下止點 lower dead center(bottom dead center) 上止點前 budc(before upper dead center) 上止點后 atdc(after top dead cetner) 下止點前 bbdc(before bottom de

17、ad center) 下止點后 abdc(after bottom dead center) 缸徑 cylinder bore 缸徑與行程 bore and stroke 空氣室 energy chamber 氣缸余隙容積 cylinder clearance volume 燃燒室容積 combustion chamber volume 氣缸最大容積 maximum cylinder volume 壓縮室 compression chamber 排氣量 displacement 發動機排量 engine displacement 活塞排量 piston swept volume 氣缸容量 cy

18、linder capacity 單室容量 single-chamber capacity 容積法 volumetry 壓縮比 compression ratio 臨界壓縮比 critical compression ratio 膨脹比 expansion ratio 面容比 surface to volume ratio 行程缸徑比 stroke-bore ratio 混合比 mixture ratio 壓縮壓力 compression pressure 制動平均有效壓力 brake mean effective pressure(bmep) 空燃比 air fuel ratio 燃空比 fu

19、el air ratio 燃料當量比 fuel equivalence ratio 扭矩 torque 單缸功率 power per cylinder 升功率 power per liter 升扭矩 torque per liter 升質量 mass per liter 減額功率 derating power 輸出馬力 shaft horsepower 馬力小時，馬力時 horsepower-hour 總馬力 gross horse power 總功率 gross power 凈功率 net power 燃油消耗量 fuel consumption 比燃料消耗率 specific fuel c

20、onsumption 空氣消耗率 air consumption 機油消耗量 oil consumption 有效馬力 net horse power 額定馬力 rated horse power 馬力重量系數 horsepower-weight factor 制動功率 brake horse power 制動熱效率 brake thermal efficiency 總效率 overall efficiency 排煙極限功率 smoke limiting horsepower 功率曲線 power curve 機械損失 mechanical loss 機械效率 mechanical effic

21、iency 有效熱效率 effective thermal efficiency 充氣系數 volumetric efficiency 過量空氣系數 coefficient of excess air 適應性系數 adaptive coefficient 扭矩適應性系數 coefficient of torque adaptibility 轉速適應性系數 speed adaptive coefficient 強化系數 coefficient of intensification 校正系數 correction factor 換算系數 conversion factor 活塞平均速度 mean

22、piston speed 發動機轉速 engine speed (rotational frequency) 怠速轉速 idling speed 經濟轉速 economic speed 起動轉速 starting speed 最低穩定工作轉速 lowest continuous speed with load 最大扭矩轉速 speed at maximum torque 最高空轉轉速 maximum no load governed speed 調速 speed governing 超速 overspeed 怠速 idling 轉速波動率 speed fluctuation rate 工況 w

23、orking condition(operating mode) 額定工況 declared working condition 變工況 variable working condition 穩定工況 steady working condition 空載 no-load 全負荷 full load 超負荷 overload 部分負荷 part load 充量（進氣） charge 旋轉方向 direction of rotation 順時針 clockwise 逆時針 counter-clockwise 左轉 left-hand rotation 右轉 right-hand rotation

24、 外徑 major diameter 中徑 pitch diameter 內徑 minor diameter 徑向間隙 radial clearance 發動機性能 engine performance 加載性能 loading performance 起動性能 starting performance 加速性能 acceleration performance 動力性能 power performance 排放性能 emission performance 空轉特性 no load characteristics 負荷特性 part throttle characteristics 調速特性

25、 governor control characteristics 萬有特性 mapping characteristics 穩定調速率 steady state speed governing rate 氣缸體和氣缸蓋 cylinder block and head 氣缸體 cylinder block 整體鑄造 cast inblock (cast enblock) 發動機罩 engine bonnet 氣缸體加強筋 engine block stiffening rib 氣缸 cylinder （轉子機）缸體 stator 缸徑 cylinder bore 氣缸體機架 cylinder

26、block frame 氣缸蓋 cylinder head 配氣機構箱 valve mechanism casing 氣缸體隔片 cylinder spacer 氣缸蓋密封環 cylinder head ring gasket 氣缸蓋墊片 cylinder head gasket 氣缸套 cylinder liner(cylinder sleeve) 干式缸套 dry cylinder liner 濕式缸套 wet cylinder liner 氣缸水套 water jacket 膨脹塞 expansion plug 防凍塞 freeze plug 氣缸壁 cylinder wall 環脊 r

27、ing ridge 排氣口 exhaust port 中間隔板 intermediate bottum 導板 guideway 創成半徑（轉子機） generating radius 缸體寬度（轉子機） operating width 機柱 column 燃燒室 combustion chamber 主燃燒室 main combustion chamber 副燃燒室 subsidiary combustion chamber 預燃室 prechamber 渦流燃燒室 swirl combustion chamber 分開式燃燒室 divided combustion chamber 渦流式燃燒

28、室 turbulence combustion chamber 半球形燃燒室 hemispherical combustion chamber 浴盆形燃燒室 bathtub section combustion chamber L形燃燒室 L-combustion chamber 楔形燃燒室 wedge-section combustion chamber 開式燃燒室 open combustion chamber 封閉噴射室 closed spray chamber 活塞頂內燃燒室 piston chamber 爆發室 explosion chamber 燃燒室容積比 volume rati

29、o of combustion cahmber 燃燒室口徑比 surface-volume ratio of combustion chamber 通道面積比 area ratio of combustion chamber passage 曲軸箱通氣口 crankcase breather 凸輪軸軸承座 camshaft bearing bush seat 定時齒輪室罩 camshaft drive(gear)cover 曲軸箱檢查孔蓋 crankcase door 曲軸箱防爆門 crankcase explosion proof door 主軸承蓋 main bearing cap 氣缸蓋

30、罩 valve mechanism cover 飛輪殼 flywheel cover 掃氣儲器 scavenging air receiver 活塞 piston 裙部開槽活塞 split skirt piston U形槽活塞 U-slot piston 滾花修復活塞 knurled piston 圓頂活塞 dome head piston 平頂活塞 flat head piston 凸頂活塞 crown head piston(convex head piston) 凹頂活塞 concave head piston 階梯頂活塞 step-head piston 筒形活塞 trunk pist

31、on 橢圓形活塞 oval piston 抗熱變形活塞 autothermic piston 不變間隙活塞 constant clearance piston 鑲因瓦鋼片活塞 invar strut piston 直接冷卻式活塞 direct-cooled piston 間接冷卻式活塞 indirect cooled piston 滑裙活塞 slipper piston 活塞速度 piston speed 活塞頂部 piston head 活塞裙部 piston skirt 整體活塞裙 solid skirt 活塞裙擴大襯簧 piston skirt expander 滑履式活塞裙 slipp

32、er skirt 隔熱槽 heat dam 活塞標記 piston mark 活塞銷 piston pin 活塞銷孔 piston pin boss 活塞銷襯套 piston pin bushing 全浮式活塞銷 full-floating piston pin 半浮式活塞銷 semifloating piston pin 固定螺釘式活塞銷 set screw piston pin 活塞環 piston ring 組合式活塞環 compound piston ring 同心活塞環 concentric piston ring 偏心活塞環 eccentric piston ring 自由環 fr

33、ee ring 閉合環 closed ring 梯形環 keystone ring 半梯形環 half keystone ring 矩形環 rectangular ring 油環 oil control ring 開槽油環 slotted oil control ring 螺旋彈簧加載雙坡口油環 coil spring loaded slotted oil control ring 漲環 expander 雙坡口油環 double bevelled oil control ring 內上坡口 internal bevel top 內下坡口 internal bevel bottom 邊緣坡口油

34、環 bevelled-ege oil control ring 刮油環 scrapper ring 鉤形環 napier ring 鍍鉻活塞環 chrome plated piston ring 活塞襯環 piston ring expander 活塞環槽 piston ring groove 活塞環區 ring zone 活塞環岸 piston ring land 活塞環內表面 back of ring 曲柄連桿機構 connecting rod 中心曲柄連桿機構 central-located connecting rod 偏心曲柄連桿機構 offset connecting rod 鉸接

35、曲柄邊桿機構 hinged connecting rod 連桿 connecting rod 連桿小頭 connecting rod small end 連桿大頭 connnecting rod big end 連桿桿身 connecting rod shank 副連桿 slave connecting rod 叉形連桿 fork-and-blade connecting rod 主連桿 main connecting rod 方形連桿 boxed rod 絞鏈?zhǔn)竭B桿 hinged type connecting rod 活節式連桿 articulated connecting rod 連桿蓋

36、 connecting rod cap 連桿軸承 connecting rod bearing 曲軸 crankshaft 整體式曲軸 one-piece crankshaft 組合式曲軸 assembled crankshaft 右側曲軸 right-hand crankshaft 左側曲軸 left-hand crankshaft 改變行程的曲軸 stroked crankshaft 曲軸前端 crankshaft front end 曲軸主軸頸 crankshaft main journal 軸頸重疊度 shaft journal overlap 圓角 fillet 主軸承 main b

37、earing 曲軸止推軸承 crankshaft thrust bearing 薄臂軸瓦 thin wall bearing shell 曲軸油道 crankshaft oil passage 曲柄 crank 曲柄臂 crank arm 曲柄銷 crank pin 軸套 bush 曲柄轉角 crank angle 曲柄半徑 crank radius 拋油圈 oil slander 角度輪 degree wheel 動平衡機 dynamic balancer 平衡重 balancer weight 扭振減振器 torshional vibration damper 扭振平衡器 torsion

38、balancer 諧振平衡器 harmonic balancer 振動平衡器 vibration balancer 曲軸鏈輪 crankshaft sprocket 轉子軸頸 rotor journal 偏心軸 eccentric shaft 曲軸箱 crankcase 閉式曲軸箱通風裝置 closed-crankcase ventilating system 飛輪 flywheel 飛輪齒圈 flywheel ring gear 飛輪芯棒 cantilever 飛輪芯軸 flywheel spindle 飛輪的慣量矩 flywheel moment of inertia 飛輪標記 flywh

39、eel mark 當量系統 equivalent system 當量軸長 equivalent shaft length 一級往復慣性力 reciprocating inertia force,1st order 二級往復貫性力 reciprocating inertia force, 2nd order 離心慣性力 centrifugal inertia force 配氣機構 valve gear 凸輪軸 camshaft 凸輪 cam 整體式凸輪軸 one-piece camshaft 組合式凸輪軸 assembled camshaft 凸輪軸驅動機構 camshaft drive 賽車用

40、凸輪軸 race camshaft 凸輪軸軸頸 camshaft bearing journal 凸輪軸軸承 camshaft bearing 凸輪軸偏心輪 camshaft eccentric 凸輪軸鏈輪 camshaft sprocket 凸輪軸正時齒輪 camshaft timing gear 凸輪軸齒輪 camshaft gear wheel 進口凸輪 inlet cam 排氣凸輪 exhaust cam 快升凸輪 quick lift cam 快升緩降凸輪 quick lift gradual clsing cam 凸輪輪廓 cam contour 凸輪包角 cam angle 凸輪

41、升程 cam-lobe lift 凸輪尖 cam nose 凸輪從動件 cam follower 齒輪傳動機構 gear drive 正時齒輪 timing gear 鏈傳動機構 chain drive 鏈輪 sprocket wheel 鏈輪盤 chain sprocket 正時鏈條 timing chain 帶齒皮帶 toothed timing belt 鏈條張緊輪 chain tension gear 半速齒輪 half speed gear 正時齒輪刻印記號 timing gear punch mark 氣門 valve 進氣過程 intake process 換氣過程 gas ex

42、change process 掃氣過程 scavenging process 給氣比 delivery ratio 分層充氣 stratified charge 充量系數 volumetric efficiency 渦流比 swirl rate 進氣渦流 intake swirl 螺旋進氣道進氣 helical duct intake 導流屏式氣門進氣 masked valve intake 切向進氣道進氣 tangential duct intake 進氣紊流 intake trubulence 進氣提前角 intake advance angle 進氣持續角 intake duration

43、 angle 進氣遲后角 intake lag angle 進面值 time-area value 氣門升程 valve lift 氣門正時 valve timing 掃氣口面積 scavenging port area 菌形氣門 mashroom valve, poppet valve 鈉冷卻氣門 sodium filled valve(natrium cooled valve) 雙氣門 dual valve 進氣門 intake valve (suction valve,inlet valve) 排氣門 exhaust valve 頂置氣門 overhead valve 側置氣門 side

44、 valve 傾斜氣門 inclined overhead valve 直立氣門 vertical overhead valve 套筒式滑閥 sleeve valve 氣門機構 valve gear 直接式氣門驅動機構 direct valve gear 間接式氣門驅動機構 indirect valve gear 氣門桿 valve stem 加大氣門桿 oversize valve stem 氣門頭 valve head 氣門工作面 valve face 氣門邊限 valve margin 氣門彈簧座 valve-spring retainer 氣門鎖片 valve key 氣門間隙調節螺釘

45、 valve lash adjusting screw 氣門旋轉器 valve rotator 氣門室 valve cage 氣門油封 valve oil seal 氣門口 valve port 氣門座 valve seat 氣門座鑲?cè)Γㄇ惰偸綒忾T座圈） valve seat insert(valve seat ring) 氣門座錐角 valve seat angle 氣門座寬度 valve seat width 氣門挺桿 valve tappet(valve lifter) 液力挺桿 hydraulic tappet(lifter) 無間隙挺桿 zero-rush tappet (non-c

46、learance tappet) 筒形挺桿 barrel type tappet 油壓挺桿 ooil tappet 滾輪挺桿 roller tappet(lifter) 挺桿轉位 tappet rotation 排氣門挺桿 exhaust valve lifter 氣門導管 valve guide 氣門桿導管 stem guide 氣門重疊度 stem overlap 氣門開啟持續時間 valve duration 氣門正時標記 valve timing sign 氣門彈簧 valve spring 氣門內彈簧 inner valve spring 氣門外彈簧 outer valve spri

47、ng 剛性緩沖彈簧 stiff buffer spring 上緊彈簧 energizing spring 防振氣門彈簧 non-surging spring 彈簧座圈 spring retainer 蝶形彈簧 belleville spring 滾柱 roller 氣門室蓋 valve chamber cover 搖臂 rocker arm 高升程搖臂 high lift rocker arm 搖臂軸 rocker arm shaft 推桿 push-rod 搖臂支架 rocker arm bracket 氣門搖臂室罩 valve rocker chamber cover 導向輪 guide

48、wheel 導桿 slide bar 導軌 slide rail 張緊輪 tensioning wheel 鏈條張緊調節裝置 assembly chain tension adjuster 張緊帶輪 tensioning pulley 傳動帶張緊裝置 belt tensioner 同步驅動皮帶 synchronous belt 同步驅動皮輪 synchronous belt pulley 供油系 fuel system 控制燃燒系統 controlled combustion system 反濕氣裝置 antipercolator 電子燃油噴射 electronic fuel injectio

49、n 蒸氣回收裝置 vapor recovery system 燃油蒸氣回收系統 fuel vapor recovery system 液體回收裝置 liquid withdrawal system 恒量凈化管 constant purge line 碳罐凈化管 canister purge line 供油量 fuel delivery 循環供油量 fuel delivery per cycle 額定供油量 rated fuel delivery 怠速供油量 idling speed fuel delivery 供油規律 fuel supply rate curve 油量調節裝置 fuel co

50、ntrol unit 供油提前角 fuel supply advance angle 進油計量 inlet metering 幾何供油行程 geometric fuel delivery stroke 供油率 fuel supply rate 燃油通道 fuel gallery 有效行程 effective stroke 剩余行程 remainder stroke 變行程計量 variable stroke metering 等容卸載 constant volume unloading 變?nèi)菪遁d variable volume unloading 收縮容積 retraction volume

51、燃油噴油裝置 fuel injection equipment 燃油噴射泵 fuel injection pump 滾輪式燃油噴射泵 roll fuel injection pump 凸輪軸式燃油噴射泵 camshaft fuel injection pump 直列式燃油噴射泵 in-line fuel injection pump 伺服式燃油噴射泵 servo fuel injection pump 底部突緣安裝燃油噴射泵 base flanged mounted fuel injection pump 上部安裝燃油噴射泵 high flanged-mounted fuel injectio

52、n pump 側向安裝燃油噴射泵 side-mounted fuel injection pump 端部突緣安裝式燃油噴射泵 end flange-mounted fuel injection pump V形燃油噴射泵 vee fuel injection pump 脈動式燃油噴射泵 jerk fuel injection pump 螺紋安裝燃油噴射泵 screw-mounted fuel injection pump 蓄能式燃油噴射泵 accumulator fuel injection pump 往復式燃油噴射泵 reciprocating fuel injection pump 驅動軸式

53、燃油噴射泵 driveshaft fuel injection pump 單缸式燃油噴射泵 single cylinder fuel injection pump 圓柱式燃油噴射泵 cylindrical fuel injection pump 旋轉式燃油噴射泵 rotary fuel injection pump 分配式燃油噴射泵 distributor fuel injection pump 多缸燃油噴射泵 multicylinder fuel injection pump 框架安裝式燃油噴射泵 cradle mounted injection pump 噴油始點 fuel injecti

54、on beginning 噴油終點 fuel injection end 噴油持續角 fuel injection duration angle 噴油延遲 injection delay 引燃噴射 pilot injection 啟噴壓力 injection starting pressure 峰值噴油扭矩 peak injection torque 峰值噴油壓力 peak injection pressure 噴油泵油缸數目 number of cylinders of an injection pump 無氣噴射 solid injection 噴射正時 injection timing

55、集中噴射 group injection 噴油器 injector 整體式噴油器 unit injector 噴嘴 nozzle 軸針式噴嘴 pintle type nozzle 環槽式噴嘴 annular slot nozzle 孔式噴嘴 hole type nozzle 長桿噴嘴 long stem nozzle 孔板式噴嘴 orifice plate nozzle 開式噴嘴 open nozzle 閉式噴嘴 closed nozzle 噴油提前器 timing advance unit 噴射泵殼體 injection pump housing 針閥 needle 芯軸 central s

56、pindle 噴嘴殼體 nozzle body 針閥升程 needle lift 噴嘴蓋形螺母 nozzle cap nut 噴油器殼體 nozzle holder 突緣安裝噴油器殼體 flanged-mounted injection nozzle holder 燃油噴射泵傳動裝置 transmision of an injection pump 噴嘴錐體 nozzle hole cone 柱塞 plunger 柱塞套 barrel 柱塞行程 plunger stroke 噴孔 spray orifice 海拔控制器 altitude control 提前器飛錘 flyweight 噴孔長徑

57、比 ratio of nozzle hole length nozzle diameter 噴嘴液動力特性 nozzle hydrokinetic characteristics 動態相位 dynamic phase 噴孔面積 nozzle hole area 噴嘴流通特性 nozzle flow characteristic 噴油背壓 injection back pressure 高壓油管 high pressure pipe 平均噴油扭矩 mean injection torque 噴油總效率 overall pumping efficiency 峰值噴油壓力 injection pea

58、k pressure 預行程 prestroke 收縮行程 retraction stroke 燃油箱 fuel tank 油箱蓋 fuel tank 油位表 fuel level gauge 注油控制裝置 fill control system 汽油箱 gasoline tank( petrol tank) 汽油供給管 gasoline feed pipe 加油管 filler tube 放油螺塞 drain plug 吸油管 suction pipe 剛性燃油管 rigid fuel pipe 進油孔 fuel feed hole 供油管 supply pipe 通氣管 bleeding pipe 通氣管 bleeding pipe 泄油閥 spill valve 泄油孔口 spill port 進油閥 inlet valve 最大油量限制器 maximum fuel stop 滴油 dribble 燃油表 fuel gauge 輸油泵 feed pump 燃油泵 fuel pump 附裝燃油箱中的電動燃油泵