XBEE模塊點到多點的通訊演示文檔

XBEE模塊點到多點的通訊演示文檔1開發板上XBEE模塊設置要求開發板和USB板上的CH都相同，為0X0C點對多點實驗過程1,將模塊A插入U(xiǎn)SB接口底板,打開XCTU軟件進入”modemconfiguration”,先選拔您所用模塊型號(XBEE:XB24;XBEE-PRO:XBP24)然后在”Functionset”里選擇:”XBEE802.”如果您將A模塊作為”廣播端”那么您需要修改A的地址如下:DH(Destinationaddresshigh):0000DL(Destinationaddresslow):FFFFMY(16-bitsourceaddress):0(A模塊)PANID(所有模塊一樣,如:123)“WRITE”完成BASE也就是廣播端的參數設置.2,同樣的辦法將模塊B,C,D,E,F….設置成如下地址(如果您打算將B,C,D,E,F….模塊設成遠端也就是被廣播端)DH(Destinationaddresshigh):0000DL(Destinationaddresshigh):0000MY(16-bitsourceaddress):1(B模塊)MY(16-bitsourceaddress):2(C模塊)MY(16-bitsourceaddress):3(D模塊)………PANID(所有模塊要有同一個ID)“WRITE”完成對所有”REMOTE”也就是遠端模塊參數的設置3,將所有模塊插在底板上,”REMOTE”端需都加上串口回環,開發包只帶一個回環器,回環不夠可用一根導線將串口DB9的2,3腳短路,通電!4,將配置好的BASE模塊A插入U(xiǎn)SB接口板,打開XCTU軟件,選中”TERMINALAssemblepacket”,正常情況下,在空白窗口輸入一串字母”Senddata”(藍色)會收到幾個相同字母(紅色),完成一個點發送多點接收并回環的實驗2..USB板XBEE模塊設置上電后開發板UART0輸出USB板發送數據界面USB板發送了1234567890的數據此時開發板收到對應的數據報1234567890再發送一次同樣的數據報開發板再次收到數據報USB板收到一個數據報ATTX16-0數據報7E00040852444C15開發板發送了一個數據報ATTX16-0數據報7E00040852444C15將格式調整成HEX格式，USB板收到的HEX顯示將接收格式調整成hex格式