版權說明:本文檔由用戶提供并上傳,收益歸屬內容提供方,若內容存在侵權,請進行舉報或認領
文檔簡介
第四章詳細設計在初步設計中選擇的路線中詳細設計了路線平面和縱斷面線形設計,進行路基和路面的結構設計,以及斜坡、涵洞、排水系統等的設計。4.1平面設計4.1.1平曲線要素的計算圖4-1按回旋線敷設緩和曲線 圖4-1的幾何元素的計算公式如下: 以JD1為例進行計算,已知Ls=65m,R=260m,轉角為29°48′29.9″,則幾何元素的計算值為: 其他交點的幾何元素值的計算可類似算得。表4-1平曲線交點要素匯總表交點樁號轉角值曲線要素值(m)半徑緩和曲緩和曲切線曲線外距校正值線長度線參數長度長度456789101112K16+000K16+413.32429°48′29.9″(Z)26065130101.864200.26589.7523.462K17+004.55633°22′22.1″(Y)26075139.642115.681226.44112.374.92K17+375.18526°16′09.3″(Z)30065139.642102.628202.54558.6622.71K17+682.29917°00′41.7″(Y)40055148.32487.365173.76324.7670.966K18+010.12226°06′54.7″(Y)27060127.27992.737183.06497.7372.409K18+203.8214.1.2曲線主點樁號的計算以JD1為例,JD1的樁號為K16+413.324,則直緩點樁號ZH=JD1-T =K16+413.324-101.864=K16+311.460緩圓點樁號HY=ZH+Ls =K16+311.460+65=K16+376.460曲中點樁號QZ=ZH+L/2=K16+376.460+200.2657/2 =K16+411.593圓緩點樁號YH=ZH+L-Ls =K16+411.593+200.265-65=K16+446.725緩直點樁號HZ=ZH+L =K16+446.725+65=K16+511.725同理算得其他主點樁號,見表4-2:表4-2平曲線要素樁號匯總表交點樁號曲線主點樁號第一緩和曲線第一緩和曲線終曲線中點第二緩和曲線起第二緩和曲線起點點或圓曲線起點點或圓曲線終點終點41314151617K16+000K16+413.324K16+311.460K16+376.460K16+411.593K16+446.725K16+511.725K17+004.556K16+888.875K16+963.875K17+002.096K17+040.316K17+115.316K17+375.185K17+272.557K17+337.557K17+373.830K17+410.103K17+475.103K17+682.299K17+594.935K17+649.935K17+681.816K17+713.698K17+768.698K18+010.122K17+917.385K17+977.385K18+008.918K18+040.450K18+100.450K18+203.8214.1.3逐樁坐標計算圖4-2中樁坐標計算示意圖以交點JD1,K16+413.324為例進行樁號坐標計算。確定交點1的坐標為:,,圓曲線半徑,緩和曲線長度,交點相鄰直線的方位角分別為,,則直緩點K16+311.460的坐標為:緩直點K16+511.725的坐標為:同理可算得緩圓點K16+376.460的坐標為,。其他交點的逐樁坐標計算同上,詳見附表1。4.2縱斷面設計4.2.1概述縱向截面設計是在考慮并比較道路垂直線附近的技術和經濟性之后,形成一條適合車輛行駛的直線和垂直曲線的線路??v向斷面設計需要考慮路線經過重要的控制點,同時避免高填方和深挖,并考慮到規范中指定的許多指標(例如坡度,坡長和豎曲線參數)是否滿足。4.2.2豎曲線計算圖4-3豎曲線要素示意圖設變坡點相鄰兩直線段坡度分別為和,代數差為。當為“+”時,表示凹形豎曲線;為“-”,表示凸形豎曲線。各元素計算公式如下: 以變坡點K16+200為例,,,,則,為凸形曲線。則切線長 , 其他豎曲線要素可類似算得。詳見附表7。4.2.3各樁號高程計算樁號地面設計樁號地面設計高程高程高程高程(m)(m)(m)(m)K16+000552.68552.68440550.08548.8620552.43552.06446.725549.94548.9340552.09551.44460551.13549.0660551.86550.82480550.74549.2680551.73550.2500550.96549.46100552.99549.57511.725551.34549.58120552.87548.95520551.85549.66140551.5548.33540552.26549.86160550.3547.79560552.44550.06180548.96547.38580554.01550.26200546.47547.1600555.26550.46220545.89546.95620555.98550.56240545.69546.94640555.68550.46260545.35547.06660555.58550.16280546.19547.26680555.36549.66300546.89547.46700554.15548.96311.46547.13547.58720553.14548.06320547.58547.66740551.49546.96340549.13547.86760551.77545.76360550.02548.06780550.27544.56376.46550.15548.23800549.44543.36380550.32548.26820546.81542.16400551.18548.46840546.27540.96411.593551.18548.58860544.29539.76420550.81548.66880542.4538.56888.875541.66538.03280518.94520.45900541.09537.36300515.44519.25920538.51536.16320514.36518.05940534.48534.96337.557511.95517960531.52533.77340511.48516.85963.875531.04533.55360508.31515.65980529.68532.68373.83506.93514.82K17+000527.9531.72380506.48514.452.096527.7531.63400505.79513.2520527.21530.9410.103505.65512.6540528.01530.21420505.54512.0540.316528.02530.2440505.71510.8560530.35529.62460505.45509.6580529.69529.04475.103505.38508.75100525.82528.46480505.38508.45115.316526.01528.02500505.49507.3120526.06527.88520505.33506.28140529.45527.3540505.22505.39160525.87526.68560504.65504.63180524.02525.92580503.25504200523.91525.03594.935503.01503.57220523.09524.01600503.12503.42240523.37522.85620502.86502.84260523.06521.65640503.02502.26272.557520.29520.9649.935501.75501.97660500.65501.65680498.55500.9681.816498.37500.82700497.66500.02713.698496.53499.34720496.38499.01740495.11497.96760492.68496.91768.698491.68496.45780490.64495.86800493.44494.81820493.11493.76840489.94492.71860485.81491.66880484.66490.61900483.78489.57917.385484.12488.65920484.14488.52940487.6487.47960485.68486.42977.385486.25485.51980486.45485.37K18+000484.29484.328.918482.69483.8520480.24483.274.3橫斷面設計公路設計中橫斷面設計是極其重要的一部分。平面設計和垂直截面設計解決了公路的走向問題,而道路橫斷面則能決定公路的強度是否滿足交通量需求。同時,公路的多個附屬設施能保證公路的使用壽命能達到要求。也可避免雨水沖刷導致的侵蝕,霜凍造成公路起伏等導致道路提前損壞,以確保公路的穩定性。4.3.1橫斷面設計圖4.3.2路基寬度的確定查閱《公路路基設計規范》(JTGD30-2015)[7]:擬定德陽至綿陽二級公路行車道寬度3.5m,硬路肩寬度為0.75m,土路肩寬度0.75m,由此得到路基總寬度為10.0m。路拱坡度為2%。4.3.3路堤和路塹邊坡坡度的確定路堤邊坡坡度取為1:1.5~1:1.75;路塹邊坡取為1:0.5~1:0.75。4.3.4超高與加寬計算當車輛行駛到彎道部分時,由于車輛輪胎的總摩擦力是恒定的,因此為了確保行駛安全,確保充分準備的縱向摩擦力,并防止由于制動不足而導致車輛失去控制力,必須在彎道部分升高道路的外側以形成傾斜表面,通過自重來抵消車輛轉彎時產生的離心力。超高和曲率具有曲線關系,此設計公路采用超高過渡方法繞中心線旋轉計算。樁號超高值可算出匯總,詳見附表2。4.3.5土石方調配計算(1)橫向調運計算并填寫表中填缺、挖余等各欄。按填挖方分別進行閉合核算,其核算公式為:填方=本樁利用+填缺挖方=本樁利用+挖余(2)縱向調運①當調運的距離小于或等于經濟運距時,采用縱向調運將路塹挖方調來填筑路堤時經濟的,若調運距離超過經濟運距時,則應考慮就近借方。②經濟運距的計算公式:L經=BT式中:L經—經濟運距(m);B—借方單價(元/m3);T—超運運費單價(元/m3.m);.L免—免費運距(m)。③《預算定額》中規定:土石方的運距,第一個20m(系指人工運輸,若為輕軌運輸則為50m)為免費運距,如不足20m者亦按20m計算,此后每增加10m(若為輕軌運輸則為50m)為一超運距單位,位數不滿5m者不計,滿5者按10m計。(四)運量計算①土石方運量即平均運距與調配土石方數量的乘積。②工程定額將人工運輸?shù)钠骄\(yùn)運距按每10m為一運輸單位,稱之為“級”,10m為一級,在路基土石方數量表中記作①,20m為二級,記作②,其余以此類推。③運量的計算公式:W=Q×n式中:W——運量(m3.10m);Q——調配土石方數量(m3);n——平均超運運距單位,其值為n=(五)計價土石方數量的計算在土石方計算與調配中,所有挖方東都應該計算價格,但填方是否計價要按土的來源決定,如果是在外面就近借土就應該計算價格,假如是在本施工區域內進行的挖方來填土則不應計算價格,計價土石方數量的計算公式:V計=式中:V計——計價土石方數量(m3);V挖——挖方數量(m3);V借——借方數量(m3);計算完成之后填寫路基設計表(附表5)、路基每公里土石方計算表、路基土石方數量匯總表(附表3)。路基每公里土石方數量表德陽至綿陽K16+000-K18+000起訖樁號長度挖方(m3)填方(m3)本樁利用遠運利用借方備注總體積土方總數量土方土方土方平均運距(Km)土方平均運距(m)松土普通土硬土(m3)(m3)(m3)(m3)土方(m3)(Km)K16+000~K17+000100046873.84687.432811.69374.83575.93575.9278.93297.00.521調出土37121.568K17+000~K18+00010006423.2642.34496.31284.639543.839543.82695.236848.60.806調入土34215.016
調出土248.121K18+000~K18+203.821204409.240.9286.481.810251.410251.4333.63176.41.5086741.40.035調入土3154.673小計53706.25370.637594.310741.253371.053371.03307.643322.06741.4第五章路基設計5.1路基設計的基本要求路基應具有足夠的強度和穩定性,并應根據適用的條件和地質,水文和材料條件等,結合經濟合理的施工方法進行設計。影響路基強度和穩定性的地表水和地下水應被攔截,并在路基外橫向排放。設計排水設施時,請確保排水順暢,并考慮到附近農田的灌溉。在路基施工中產生大量借來的和不適用的土壤時,打樁土方必須減少耕地的占用,并防止被雨水沖走并阻塞排水系統。應結合當?shù)貙?shí)際經驗,對特殊條件下的路基進行研究和調查,從而進行個性化設計。5.1.1路基寬度《公路工程技術標準》(JTGB01-2014)規定:“設計速度為60km/h時,二級公路的車道寬度為3.5m,硬路肩寬度為0.75m,土路肩寬度取0.75m,路基寬度10.0m”。5.1.2路基高度路基的高度應設計成路基兩側地面的水位低于路肩的邊緣。路基的強度和穩定性會受到地下水,毛細水凍結的影響。路基高度應按具體填挖高度確定。5.1.3路基壓實公路路基的壓實度應符合表5-1的要求:表5-1路基壓實表填挖類別路床頂面以下深度/m路基壓實度/%高速、一級公路三級公路三、四級公路填方路基0至0.30.3至0.8挖方路基0至0.30.3至0.8-5.1.4邊坡坡度5.1.4.1路塹邊坡坡度路塹邊坡坡度,應根據當?shù)刈匀粭l件、土石種類及其結構、邊坡高度和施工方法確定。一般土取1:0.5至1:1。5.1.4.2路堤邊坡坡度路堤邊坡坡度,當路堤的基底情況良好時可參照規范規定出本設計的路堤邊坡坡度為1:1.5(小于6m)。大于6m時,下面部分路堤邊坡坡度為1:1.75。5.2路基邊坡穩定性驗算5.2.1路塹邊坡穩定性驗算本設計采用曲線滑動面邊坡穩定性分析法進行邊坡穩定性驗算。樁號K16+700處附近,挖方高度最大,為5.19m,需要進行邊坡穩定性驗算。已知K16+700處樁號的路塹邊坡坡度為1:0.5,采用曲線滑動面邊坡穩定性分析中的條分法的圖解法進行穩定性驗算?;瑒?dòng)面上的粘結力c=10kPa,邊坡材料容重r=25kN/,H=5.19m。利用K=1.0(極限平衡條下令),令,則,查圖5-2知,當時,得,而由,得,則邊坡穩定系數>1.2,可得1:0.5的邊坡滿足要求,穩定。圖5-1條分法圖解5.2.2路堤邊坡穩定性驗算本路段填方最大為K17+000,由于地面線較陡,故設置了擋土墻作為支護,具體支護見防護內容:5.3路基防護路基防護是確保道路全天候使用的必要工程措施,以確保路基不會因地表流和氣候變化而變得不穩定。路基設計的主要項目之一就是路基防護。路基防護方法一般可分為邊坡防護和沖刷防護。邊坡防護主要包括植物防護和工程防護。植物防護主要包括種草,鋪設草皮,植樹等;工程防護形式有框格防護、封面、加設護面墻、噴射混凝土邊坡防護等形式。對于土質路堤的坡面防護工程,最好在填土壓實后再進行施工,并且要根據所填料的具體性質和分層大概情況來確定具體的防護方法。坡面在施工前應該整平,有坑洼的地方應填實。沖刷防護分為間接防護和直接防護。通常安裝石質護坡與混凝土預制板等,來防止路基在水流速較慢且水破壞作用不強的區域被腐蝕。(1)路堤邊坡防護路堤高度小于3m邊坡均直接撒草種防護;路堤高度大于3m均采用方格網植草護坡。(2)路塹邊坡防護路塹高度小于3m邊坡均直接撒草種防護;路塹高度大于3m均采用網格式草坪平鋪。第六章?lián)跬翂υO(shè)計與驗算6.1擋土墻設計6.1.1設置擋土墻目的6.1.2墻身構造表6-1擋土墻尺寸尺寸墻高(m)墻頂寬(m)墻底寬(m)基礎埋深(m)墻面坡度基底坡度墻背坡度設計方案61.221.31.21:0.251:51:0.25圖6.1擋土墻橫斷面布置圖6.1.3土壤地質情況填土為粘性土,填料容重γ=20kN/m3,粘聚力c=20kpa,綜合內摩擦角φ=30°,墻背與填土間的摩擦角。根據《公路路基設計規范》(JTGD30-2015)[7]中規定:“當基底為黏土?xí)r,摩擦系數μ=0.4,地基容許承載力為σ0300kpa”。6.1.4墻身材料參考《公路圬工橋涵設計規范》(JTGD61-2005)[20]規范標準:“采用M7.5號砂漿,石材強度等級MU30,砌體容重γk=23kN/m3,砌體材料極限抗壓強度Rk取16006.1.5車輛荷載為計算方便,根據《公路路基設計規范》(JTGD30-2015)[7]規定:“車輛荷載作用在擋土墻墻背填土上引起的附加土體側壓力,換算成等效均布土層厚度”。6.2土壓力計算6.2.1求破裂角θ假設破裂面交于荷載范圍內,則有:根據路堤擋土墻破裂面交于荷載內部時破裂角的計算公式,則有:故6.2.2主動土壓力計算根據路堤擋土墻破裂面交于荷載內側的土壓力計算公式:6.2.3土壓力作用點位置確定6.3穩定性驗算6.3.1墻身截面性質計算將擋土墻在CAD中繪圖后,使用CAD面域功能,可直接得到截面面積和形心位置,下面是繪圖結果和相關參數:墻身重力6.3.2抗滑穩定性驗算滿足要求驗算采用“極限狀態分項系數法”??够瑒?dòng)穩定系數為:∴抗滑穩定性滿足要求。6.3.3抗傾覆穩定性驗算∴抗傾覆穩定性滿足要求。6.4基底應力及合力偏心距驗算6.4.1合力偏心距(1)軸心荷載作用時: 因此,基礎底面壓應力滿足要求。偏心荷載作用時:作用于基底的合力偏心距e如下計算:∴基底合力偏心距滿足要求。第七章路面設計7.1瀝青路面設計7.1.1交通分析(1)路面設計年限依照規范要求查表7-1各級公路瀝青路面設計年限,二級公路設計年限為12年。(2)累計標準軸載當量軸次計算我國路面設計以雙輪組單軸載100kN為標準軸載,以BZZ-100表示。1)采用彎沉值和瀝青層的層底拉應力為設計指標1.各級軸載按下式換算成標準軸載的當量軸次 2.設計年限內累計當量標準軸載數在瀝青路面設計中,既要考慮使用初期日交通量和使用年限末期交通量,還要根據路面的設計使用年限,計算出車道累計承擔多少次標準軸載的反復作用。已知設計年限t為12年,設計年限內交通量平均增長率為5%,《公路瀝青路面設計規范》(JTGD50-2017)[10]查表車道系數表,對雙向2車道取車道系數=0.5。表7-2軸載換算結果表瀝青混合料層永久變形以瀝青混合料層永久變形為設計指標PiC1C2nic1c2ni()4SH130前軸25.5514.535621.09后軸45.11135645.51大貨車JN150前軸4914.5612103.77后軸101.611612426.22中貨車EQ-140前軸23.714.535614.20后軸69.211356229.31五十鈴前軸6014.56681.65后軸1003.2166448.00小貨車BJ130前軸13.5514.518462.73后軸27.21118469.85日野KB222前軸50.214.5356200.04后軸104.311356828.39小客車前軸16.514.54123.34后軸23114122.80大客車CA50前軸28.714.523327.48后軸68.211233194.71中貨車CA50前軸28.714.545321.37后軸68.211453151.442)采用半剛性材料結構層的層底拉應力為設計指標表7-3軸載換算結果表(半剛性基層層底拉應力)以路基頂面豎向壓應變?yōu)樵O(shè)計指標PiC1C2nic1c2ni()5SH130前軸25.5514.53565.39后軸45.11135620.52大貨車JN150前軸4914.561250.85后軸101.611612433.04中貨車EQ-140前軸23.714.53563.36后軸69.211356158.68五十鈴前軸6014.56648.99后軸1008.71661218.00小貨車BJ130前軸13.5514.518460.37后軸27.21118462.68日野KB222前軸50.214.5356100.42后軸104.311356864.01小客車前軸16.514.54120.55后軸23114120.64大客車CA50前軸28.714.52337.89后軸68.211233132.79中貨車CA50前軸28.714.54536.13后軸68.211453103.283)采用無機結合料穩定層疲勞為設計指標表7-4軸載換算結果表(無機結合料穩定層疲勞)以無機結合料穩定層疲勞為設計指標PiC1C2nic1c2ni()13SH130前軸25.5514.53569.79E-05后軸45.1113560.035131大貨車JN150前軸4914.56120.168975后軸101.611612491.6751中貨車EQ-140前軸23.714.53563.35E-05后軸69.2113568.344095五十鈴前軸6014.5660.822824后軸1003.8166532小貨車BJ130前軸13.5514.518464.2E-08后軸27.21118468.03E-05日野KB222前軸50.214.53560.405004后軸104.3113561210.024小客車前軸16.514.54123.02E-07后軸23114125.04E-06大客車CA50前軸28.714.52330.000363后軸68.2112336.214975中貨車CA50前軸28.714.54530.000984后軸68.2114537.087785已知設計年限t為12年,設計年限內交通量平均增長率為4.5%,《公路瀝青路面設計規范》(JTGD50-2017)[10]查兩車道系數表,對雙向2車道取車道系數η=0.5。設計年限內一個車道通過的累計當量標準軸次:(3)交通等級以營運車輛中的大客車、中型貨車、大型貨車、拖掛車等車型在一個車道上的日平均車數進行劃分,查表,路面交通等級屬于重交通。表7-5瀝青路面交通等級交通量等級BZZ-100KN累計標準軸次/(萬次/一車道)軸重6t以上貨車/[輛/(d·車道)]低交通150<400輕交通150-400400-1000中交通400-8001000-2000重交通800-20002000-5000超重交通2000-40005000-10000特重交通>4000>10000(4)結構組合與材料選取1)土基回彈模量的確定土基回彈模量擬設為65MPa,最小防凍層為60cm。7.1.2路面結構設計本項目沿線區域主要為碎石土,其中一些為石質路基,路基一般處于干燥狀態。根據《公路瀝青路面設計規范》(JTGD50-2017)[10]:“土壤基層的回彈模量為E0=50MPa,回彈模量濕度調節系數為1.0,干濕與凍融循環作用折減系數取1.0。調節濕度并減少干濕循環和凍融循環的影響后,路基頂面回彈模量為50MPa。根據《公路瀝青路面設計規范》(JGD50-2017)[10],并考慮交通條件,結構層的最小施工厚度、施工設備、水文條件、區域材料類型和經濟效益,初擬各結構層的厚度和材料,參數如下:表7-5初擬路面結構結構層編號層位材料類型厚度(mm)模量(MPa)泊松比2中面層中粒式密集配瀝青混凝土(AC-20)60110000.253下面層粗粒式密級配瀝青混凝土(AC-25)60120000.254基層水泥穩定碎石30090000.255底基層級配碎石1503960.356土基500.47.2路面結構驗算無機結合料穩定層層疲勞開裂驗算將瀝青混凝土層以上作為上層,,厚度h,水泥穩定碎石層為中間層,,厚度為H=300mm,把級配碎石層看成路基改善層,下層為級配碎石層和土基,。根據《公路瀝青路面設計規范JTGD50-2017》[10]表3.0.3:“標準車型輪胎接地壓強,單輪接地當量圓半徑”。由,,,查諾模圖得。則:根據《公路瀝青路面設計規范》(JTGD50-2017)[10]表G.1.2:“按氣溫條件相近地區的系數值取用。則基準路面結構溫度調整系數取1.18,根據初擬路面結構和路面結構層材料參數,按式(G.1.3-1)計算得到溫度調整系數”。則溫度調整系數:由表B.2.1-1,對于無機結合料穩定粒料,疲勞開裂模型參數a=13.24,b=12.52。由表5.4.5,彎拉強度為1.5MPa。由表3.0.1得二級公路目標可靠指標為1.04。根據以上參數,按式(B.2.1-1)計算得到無機結合料穩定層疲勞開裂壽命為因?yàn)椋詿o機結合料穩定層疲勞開裂滿足。路基頂面和路表驗收彎沉值根據《公路瀝青路面設計規范》(JTGD50-2017)[10]B.7節:“確定路基頂面和路表驗收彎沉值時,采用落錘式彎沉儀,荷載盤半徑為150mm,荷載為50kN。落錘式彎沉儀承載板施加壓力”。根據公式(B.7.1)計算得到路基頂面驗收彎沉值為將中粒式瀝青混凝土層作為上層,,厚度h=60mm,粗粒式瀝青混凝土層和水泥穩定碎石層為中間層,,厚度為H,把級配碎石層看成路基改善層,下層為級配碎石層和土基,。由,,,查諾模圖得。則理論彎沉系數:路表驗收彎沉值第八章排水設計8.1路基邊坡及溝渠設計邊溝橫斷面采用矩形,矩形邊溝邊坡為1:1。邊溝的深度及寬度取用0.6m。邊溝通常選用與路線相同的縱坡值,并不小于0.5%。在特殊情況下,邊溝縱坡可采用0.3%,此時邊溝出口間距應減短。截水溝橫斷面采用矩形,邊坡采用1:1,深度及寬度采用0.6m,溝底縱坡不小于0.5%。8.1.1排水溝設計通過分析當?shù)氐匦魏团潘髞泶_定排水溝的布局。同時也需結合當?shù)氐牡匦巫匀粭l件等因素,均使用直線線性或平緩改變方向。排水溝和道路縱斷面相似,須控制縱坡度??v向斜率大于7/100時用急流槽。排水溝采用矩形斷面,,,邊坡率。水文水力計算同邊溝。8.1.2邊溝設計驗算本次設計以瀝青混凝土路面為例。粘土路基(坡度為1:0.5,坡面流最大長度為3.51m,最小長度為0.2m),路基寬度10m,路拱橫坡為2%,土路肩橫坡為3%,邊溝坡腳和路肩邊緣間設置矩形邊溝。(1)計算匯水面積和徑流系數瀝青混凝土路面匯水面積:瀝青路面徑流系數為1=0.95。挖方邊坡匯水面積:細粒土坡面和路肩徑流系數。碎落臺匯水面積:硬巖石坡面和路肩徑流系數。截水溝到路塹邊坡的匯水面積:起伏的山地徑流系數:。由此,總的匯水面積為:m2匯水區的徑流系數為=0.825(2)計算匯流歷時計算坡面匯流歷時由克畢公式計算 草皮防護路堤邊坡的粗度系數,且路堤坡度為1:1.5,得路堤坡面匯流歷時:。瀝青混凝土路面粗糙系數為,橫坡2%,坡面流長度為5m,所以,歷時時間為:。因此,取坡面匯流歷時t1=1.255(取最大值)。矩形邊溝底寬0.6m,深0.6m,漿石砌片砌筑,溝壁粗糙系數為,設計水深0.4m。求得,過水?dāng)嗝婷娣e:水力半徑:按曼寧公式: 得溝內平均流速為:因此,溝內匯流歷時為:由上得匯流歷時為:(3)計算降雨強度q值在缺乏資料時,可利用標準降雨強度等值線圖和有關轉換系數按下式進行計算: 其中: 取=1mm/min;取重現期為15年,則;取。由式得:因此:(4)檢驗徑流設定邊溝的截面形式為梯形,底寬和溝深均為0.6m,斷面積為,則泄水能力: 因?yàn)樵O(shè)計徑流量=0.0908m3/s<泄水能力=1.18m3/s,所以假定的邊溝尺寸符合要求。排水設計計算結果匯總見附表4。8.2路面排水設計道路拱門設計的目的是快速清除路面上的降水并確保行車安全。道路拱的設計包括確定路面路拱的坡度,路肩的橫向坡度和選擇路拱的形式。道路拱坡的確定應基于暢通的道路排水和確保安全穩定行駛的原則。當路面更粗糙時,雨水在路面上的流動會更緩慢,道路拱的坡度應加大,但坡度太大,不利于行駛。因此,應將路拱的坡度限制在一定范圍內。當?shù)缆菲教箷r(shí),有利于排水,道路拱的坡度應較小。根據路面類型和當?shù)刈匀粭l件,本設計行車道橫坡為2%,硬路肩橫坡為2%,路肩橫坡為3%。第九章概預算9.1工程概況本設計公路為二級公路,全長約2204米,采用的路面形式為瀝青混凝土柔性路面結構,山區公路的路基土石方的挖填量比較大,其中包含一座隧道。9.2編制依據(1)工、料、機械臺班定額引用交工發(2018)65號《公路工程概算定額》、《公路工程預算定額》;(2)交公路發[2018]612號《公路基本建設工程概算、預算編制辦法》;(3)初步設計文件及工程量。9.3工程量9.3.1土方量因無具體實際土石方分層及各種土石的詳細配比,現假定挖填所用的土質均為普通土,其中各項具體數值如下:挖土方總量:,填方總量:9.3.2基層基層分為基層和底基層,工程量計算如下:底基層材料:級配碎石;厚度:15cm;寬度:8.5m;長度2204m。工程總量:體積:2810m3基層材料:水泥穩定碎石;厚度:30cm;寬度:8.5m;長度2204m。工程總量:體積:5420m39.3.3面層材料:AC-16;厚度:6cm;寬度:8.5m;長度2204m。工程總量:體積:1124m3材料:AC-20;厚度:6cm;寬度:8.5m;長度2204m。工程總量:體積:1124m39.4編制結果具體匯總表見預算表分項編號工程或費用名稱單位總數量德陽至綿陽k16+000-k18+203.821總金額
(元)全路段
技術經濟
指標各項
費用
比例(%)數量金額
(元)技術經
濟指標1第一部分建筑安裝工程費公路公里2.2042.20478978143583400.1878978143583400.1876.28101臨時工程公路公里2.2042.204102路基工程km47760.00047760.000342934971.80342934971.8033.12103路面工程km2.2042.20423966881087426.5023966881087426.5023.15104橋梁涵洞工程km105隧道工程km/座106交叉工程處106綠化及環境保護工程處2.0002.000107交通工程及沿線設施公路公里108公路設施及預埋管線工程公路公里2.2042.2041456307660756.351456307660756.3514.07108綠化及環境保護工程公路公里109其他工程公路公里110專項費用元6154706154705.942第二部分土地使用及拆遷補償費公路公里2.2042.204201土地使用費畝202拆遷補償費公路公里2.2042.204203其他補償費公路公里2.2042.2043第三部分工程建設其他費公路公里2.2042.20424562201114437.3924562201114437.3723.72301建設項目管理費公路公里2.2042.2041873379849990.471873379849990.4718.09302研究試驗費公路公里2.2042.204303建設項目前期工作費公路公里2.2042.204431945195982.30431945195982.294.17304專項評價(估)費公路公里2.2042.204305聯合試運轉費公路公里2.2042.20463052860.7163052860.710.06306生產準備費公路公里2.2042.20411300051270.4211300051270.421.09307工程保通管理費公路公里2.2042.204308工程保險費公路公里2.2042.2043159114333.483159114333.480.31309其他相關費用公路公里2.2042.2044第四部分預備費公路公里2.2042.204401基本預備費公路公里2.2042.204402價差預備費公路公里2.2042.2045第一至四部分合計公路公里2.2042.204103540344697837.56103540344697837.56100.006建設期貸款利息公路公里2.2042.204新增加費用項目元*請?jiān)诖溯斎胭M(fèi)用項目參考文獻許金良.道路勘測設計[M].5版.北京:人民交通出版社,2018.12.陳忠達.路基路面工程[M].6版.北京:人民交通出版社,2009.?許婭婭.測量學[M].5版.北京:人民交通出版社,2020.7.?姜志青.道路建筑材料[M].5版.北京:人民交通出版社,2015.12.?任福田,劉小明等.交通工程學[M].3版.北京:人民交通出版社,2017.7.綠色公路建設指南[M].北京:人民交通出版社,2000.6.中華人民共和國行業標準.公路路基設計規范:JTGD30-2015[S].北京:人民交通出版社股份有限公司,2015中華人民共和國行業標準.公路路基施工技術規范:JTG/T3610—2019[S].北京:人民交通出版社股份有限公司,2019.中華人民共和國行業標準.公路瀝青路面設計規范:JTGD50-2017[S].北京:人民交通出版社股份有限公司,2017.中華人民共和國行業標準.公路路面基層施工技術細則:JTG/TF20-2015[S].北京:人民交通出版社股份有限公司,2015.中華人民共和國行業標準.公路排水設計規范:JTG/TD33-2012[S].北京:人民交通出版社,2013.中華人民共和國行業標準.公路工程技術標準:JTGB01-2014[S].北京:人民交通出版社,2014.中華人民共和國行業標準.公路路線設計規范:JTGD20-2017[S].北京:人民交通出版社,2017.中華人民共和國行業標準.公路路基設計規范:JTGD30-2015[S].北京:人民交通出版社,2015.中華人民共和國行業標準,城市道路工程設計規范:CJJ37-2012[S].北京:中國建筑工業出版社,2016.中華人民共和國行業標準,城市道路路線設計規范:CJJ193-2012[S].北京:中國建筑工業出版社,2012.中華人民共和國行業標準,城市道路交叉口設計規程:CJJ152-2010[S].北京:中國建筑工業出版社,2010.中華人民共和國行業標準.公路環境保護設計規范:JTGB04-2010[S].北京:人民交通出版社,2010.中華人民共和國行業標準.《公路圬工橋涵設計規范》(JTGD61-2005)[S].北京:人民交通出版社,2005.SHIMinglei1,DENGXuejun.OnPhysicalandMechanicalBehaviorof.NaturalMarineIntermediateDeposits[J].ChinaOceanEngineering,2005,19(1)WebsterS.L.,R.HGrau,andR.PWilliams.DescriptionandApplicationofDualMassDynamicConePenetrometer[R].U.S.ArmyEngineerWaterwaysExperimentStation,InstructionReport,No.GL-92-3,1992Laboratoryinvestigationonthebrucitefifiberreinforcedasphaltbinderandasphaltconcrete –RuiXiong,JianhongFang,AnhuaXu,BowenGuan,ZhuangzhuangLiu,2015致謝附表1樁號坐標匯總表樁號坐標樁號坐標N(X)E(Y)N(X)E(Y)K16+0003062116.692524976.664K16+4403061961.68525386.5224K16+0203062108.846524995.0606K16+446.7253061961.54525393.2462K16+0403062100.999525013.4571K16+4603061961.75525406.5179K16+0603062093.152525031.8536K16+4803061963.041525426.4742K16+0803062085.306525050.2501K16+5003061965.081525446.3694K16+1003062077.459525068.6466K16+511.7253061966.435525458.0164K16+1203062069.613525087.0432K16+5203061967.401525466.2343K16+1403062061.766525105.4397K16+5403061969.738525486.0973K16+1603062053.92525123.8362K16+5603061972.074525505.9604K16+1803062046.073525142.2327K16+5803061974.411525525.8234K16+2003062038.227525160.6292K16+6003061976.747525545.6865K16+2203062030.38525179.0258K16+6203061979.084525565.5495K16+2403062022.534525197.4223K16+6403061981.42525585.4126K16+2603062014.687525215.8188K16+6603061983.757525605.2756K16+2803062006.841525234.2153K16+6803061986.093525625.1387K16+3003061998.994525252.6118K16+7003061988.43525645.0017K16+311.4603061994.498525263.1528K16+7203061990.766525664.8648K16+3203061991.153525271.0108K16+7403061993.103525684.7278K16+3403061983.513525289.4933K16+7603061995.439525704.5909K16+3603061976.501525308.2221K16+7803061997.776525724.4539K16+376.4603061971.525525323.9095K16+8003062000.113525744.317K16+3803061970.576525327.3202K16+8203062002.449525764.18K16+4003061966.094525346.8064K16+8403062004.786525784.043K16+411.5933061964.186525358.2404K16+8603062007.122525803.9061K16+4203061963.123525366.5795K16+8803062009.459525823.7691樁號坐標樁號坐標N(X)E(Y)N(X)E(Y)K16+888.8753062010.495525832.5839K17+2803061898.198526198.0225K16+9003062011.783525843.6336K17+3003061889.378526215.9723K16+9203062013.875525863.5234K17+3203061881.067526234.1624K16+9403062015.332525883.4689K17+337.5573061874.496526250.4414K16+9603062015.74525903.4614K17+3403061873.652526252.7336K16+963.8753062015.663525907.3361K17+3603061867.446526271.7426K16+9803062014.727525923.4308K17+373.8303061863.902526285.1095K17+0003062012.182525943.2633K17+3803061862.52526291.1227K17+002.0963062011.827525945.329K17+4003061858.896526310.7879K17+0203062008.12525962.8415K17+410.1033061857.566526320.8022K17+0403062002.567525982.0498K17+4203061856.582526330.65K17+040.3163062002.467525982.3502K17+4403061855.385526350.6124K17+0603061995.614526000.7983K17+4603061854.907526370.6061K17+0803061987.608526019.1242K17+475.1033061854.774526385.7082K17+1003061978.944526037.1493K17+4803061854.74526390.6054K17+115.3163061972.098526050.8507K17+5003061854.602526410.6049K17+1203061969.996526055.0361K17+5203061854.465526430.6044K17+1403061961.021526072.9092K17+5403061854.327526450.604K17+1603061952.046526090.7823K17+5603061854.189526470.6035K17+1803061943.071526108.6554K17+5803061854.051526490.603K17+2003061934.096526126.5285K17+594.9353061853.948526505.5375K17+2203061925.12526144.4016K17+6003061853.913526510.6025K17+2403061916.145526162.2747K17+6203061853.657526530.6007K17+2603061907.17526180.1478K17+6403061852.945526550.5872K17+272.5573061901.535526191.3696K17+649.9353061852.31526560.5015樁號坐標樁號坐標N(X)E(Y)N(X)E(Y)K17+6603061851.423526570.5273K18+0403061731.059526928.5363K17+6803061848.914526590.3672K18+040.4503061730.788526928.8953K17+681.8163061848.637526592.1619K18+0603061718.485526944.0852K17+7003061845.416526610.0569K18+0803061705.149526958.9885K17+713.6983061842.455526623.4303K18+1003061691.441526973.5512K17+7203061840.941526629.5476K18+100.4503061691.131526973.8776K17+7403061835.626526648.8273K18+1203061677.668526988.0536K17+7603061829.809526667.9626K18+1403061663.896527002.5559K17+768.6983061827.212526676.2638K18+1603061650.123527017.0583K17+7803061823.831526687.0483K18+1803061636.351527031.5607K17+8003061817.848526706.1324K18+2003061622.578527046.063K17+8203061811.866526725.2166K18+203.8213061619.948527048.8333K17+8403061805.883526744.3007K17+8603061799.9526763.3849K17+8803061793.917526782.4691K17+9003061787.934526801.5532K17+917.3853061782.733526818.1423K17+9203061781.951526820.6373K17+9403061775.855526839.6854K17+9603061769.23526858.5548K17+977.3853061762.688526874.66K17+9803061761.623526877.0478K18+0003061752.717526894.9503K18+008.9183061748.323526902.7104K18+0203061742.51526912.1446附表2超高計算匯總表樁號以下各點與設計高程之高差(m)左側中樁右側外緣內緣內緣外緣K16+00000.020.110.0202000.020.110.0204000.020.110.0206000.020.110.0208000.020.110.02010000.020.110.02012000.020.110.02014000.020.110.02016000.020.110.02018000.020.110.02020000.020.110.02022000.020.110.02024000.020.110.02026000.020.110.02028000.020.110.02030000.020.110.020311.460.010.020.110.0203200.010.020.110.090.0734000.020.130.240.22360-0.0300.190.380.36376.46-0.0400.250.50.47380-0.0400.250.50.47400-0.0400.250.50.47411.593-0.0400.250.50.47420-0.0400.250.50.47440-0.0400.250.50.47446.725-0.0400.250.50.47460-0.0300.20.410.39480-0.010.020.140.260.245000.010.020.110.110.09511.7250.010.020.110.02052000.020.110.02054000.020.110.02056000.020.110.02058000.020.110.02060000.020.110.02062000.020.110.02064000.020.110.02066000.020.110.02068000.020.110.02070000.020.110.02072000.020.110.02074000.020.110.02076000.020.110.02078000.020.110.02080000.020.110.02082000.020.110.02084000.020.110.02086000.020.110.02088000.020.110.020888.87500.020.110.020.019000.080.10.110.020.019200.210.230.120.0209400.330.350.180.01-0.029600.450.470.240-0.04963.8750.470.50.250-0.049800.470.50.250-0.04K17+0000.470.50.250-0.042.0960.470.50.250-0.04200.470.50.250-0.04400.470.50.250-0.0440.3160.470.50.250-0.04600.360.380.190-0.03800.230.260.140.0201000.10.130.110.020.01115.31600.020.110.020.0112000.020.110.02014000.020.110.02016000.020.110.02018000.020.110.02020000.020.110.02022000.020.110.02024000.020.110.02026000.020.110.020272.5570.010.020.110.0202800.010.020.110.080.0630000.020.130.230.21320-0.0300.190.380.35337.557-0.0400.250.50.47340-0.0400.250.50.47360-0.0400.250.50.47373.83-0.0400.250.50.47380-0.0400.250.50.47400-0.0400.250.50.47410.103-0.0400.250.50.47420-0.0400.220.430.41440-0.010.010.150.290.274600.010.020.110.140.12475.1030.010.020.110.02048000.020.110.02050000.020.110.02052000.020.110.02054000.020.110.02056000.020.110.02058000.020.110.020594.93500.020.110.020.016000.040.060.110.020.016200.190.210.120.0206400.330.360.180.01-0.02649.9350.40.430.210-0.046600.40.430.210-0.046800.40.430.210-0.04681.8160.40.430.210-0.047000.40.430.210-0.04713.6980.40.430.210-0.047200.360.380.190-0.037400.220.240.130.0207600.070.090.110.020.01768.69800.020.110.020.0178000.020.110.02080000.020.110.02082000.020.110.02084000.020.110.02086000.020.110.02088000.020.110.02090000.020.110.020917.38500.020.110.020.019200.020.040.110.020.019400.190.210.120.0209600.350.370.190.01-0.03977.3850.470.50.250-0.049800.470.50.250-0.04K18+0000.470.50.250-0.048.9180.470.50.250-0.04200.470.50.250-0.04附表3路基土石方數量匯總表土石方計算表1樁號橫斷面距離(m)挖方分類及數量(m3)填方數量(m3)面積總數量(m2)挖方填方總數量土石12345181920K16+0002.171.2320.0078.512.312.3K16+0205.680.0020.00154.9K16+0409.800.0020.00259.4K16+06016.140.0020.00410.1K16+08024.870.0020.00843.0K16+10059.430.0020.001307.8K16+12071.350.0020.001267.3K16+14055.380.0020.00975.7K16+16042.190.0020.00676.6K16+18025.460.0020.00261.765.265.2K16+2000.716.5220.0014.5193.4193.4K16+2200.7512.8220.0014.7279.1279.1K16+2400.7215.0920.0014.5374.9374.9K16+2600.7322.4020.0014.6352.6352.6K16+2800.7312.8620.0014.5201.0201.0K16+3000.727.2411.468.372.872.8K16+311.4600.725.468.549.831.831.8K16+3201.581.9920.00206.219.919.9K16+34019.040.0020.00463.3K16+36027.300.0016.46450.2K16+376.46027.410.003.54101.1K16+38029.720.0020.00710.6K16+40041.340.0011.59479.8K16+411.59341.440.008.41323.7K16+42035.570.0020.00579.1K16+44022.350.006.72134.1K16+446.72517.520.00土石方計算表2樁號橫斷面距離(m)挖方分類及數量(m3)填方數量(m3)面積總數量(m2)挖方填方總數量土石12345181920K16+446.72517.520.0013.28289.3K16+46026.060.0020.00478.3K16+48021.770.0020.00451.1K16+50023.340.0011.72312.0K16+511.72529.870.008.28285.1K16+52039.040.0020.00871.9K16+54048.150.0020.00878.4K16+56039.690.0020.001056.3K16+58065.940.0020.001535.3K16+60087.590.0020.001868.5K16+62099.260.0020.001934.3K16+64094.160.0020.001998.6K16+660105.700.0020.002115.5K16+680105.860.0020.002151.2K16+700109.270.0020.002093.6K16+720100.090.0020.001862.3K16+74086.140.0020.002050.4K16+760118.900.0020.002307.7K16+780111.870.0020.002273.1K16+800115.440.0020.002065.3K16+82091.090.0020.001999.1K16+840108.820.0020.001973.6K16+86088.540.0020.001585.3K16+88069.990.008.88602.1K16+888.87565.690.0011.13714.4K16+90062.750.0020.00966.4K16+92033.890.00土石方計算表3樁號橫斷面距離(m)挖方分類及數量(m3)填方數量(m3)面積總數量(m2)挖方填方總數量土石12345181920K16+92033.890.0020.00346.272.472.4K16+9400.737.2420.0014.8406.1406.1K16+9600.7633.383.882.9138.4138.4K16+963.8750.7638.0416.139.2582.6582.6K16+9800.3934.2220.007.9773.6773.6K17+0000.4043.142.100.892.492.4K17+002.0960.4045.0717.907.2766.6766.6K17+0200.4140.5720.008.2632.3632.3K17+0400.4222.670.320.17.27.2K17+040.3160.4222.8519.68354.1224.9224.9K17+06035.560.0020.00709.9K17+08035.430.0020.00393.0247.1247.1K17+1003.8824.7115.3288.9319.3319.3K17+115.3167.7416.994.6839.174.874.8K17+1208.9714.9620.00793.1149.6149.6K17+14070.340.0020.00990.9122.4122.4K17+16028.7512.2420.00371.8280.2280.2K17+1808.4415.7920.0091.7330.2330.2K17+2000.7317.2320.0014.5294.2294.2K17+2200.7212.1920.00130.2146.7146.7K17+24012.302.4820.00383.824.824.8K17+26026.090.0012.56209.368.368.3K17+272.5577.2510.887.4433.5131.5131.5K17+2801.7524.4720.0025.1793.2793.2K17+3000.7654.8520.0015.41210.01210.0K17+3200.7766.1517.5613.11490.21490.2K17+337.5570.72103.60土石方計算表4樁號橫斷面距離(m)挖方分類及數量(m3)填方數量(m3)面積總數量(m2)挖方填方總數量土石12345181920K17+337.5570.72103.602.441.8242.4242.4K17+3400.7694.8120.0014.92429.32429.3K17+3600.73148.1213.8310.32144.42144.4K17+373.8300.76161.996.174.61015.31015.3K17+3800.73167.1220.0014.73356.03356.0K17+4000.74168.4910.107.41613.31613.3K17+410.1030.72150.899.907.11389.71389.7K17+4200.72129.9520.0014.52184.52184.5K17+4400.7388.5020.0048.21529.01529.0K17+4604.0964.4015.1045.7854.4854.4K17+475.1031.9648.754.906.6223.3223.3K17+4800.7642.4320.00
溫馨提示
- 1. 本站所有資源如無特殊說明,都需要本地電腦安裝OFFICE2007和PDF閱讀器。圖紙軟件為CAD,CAXA,PROE,UG,SolidWorks等.壓縮文件請下載最新的WinRAR軟件解壓。
- 2. 本站的文檔不包含任何第三方提供的附件圖紙等,如果需要附件,請聯系上傳者。文件的所有權益歸上傳用戶所有。
- 3. 本站RAR壓縮包中若帶圖紙,網頁內容里面會有圖紙預覽,若沒有圖紙預覽就沒有圖紙。
- 4. 未經權益所有人同意不得將文件中的內容挪作商業或盈利用途。
- 5. 人人文庫網僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對用戶上傳分享的文檔內容本身不做任何修改或編輯,并不能對任何下載內容負責。
- 6. 下載文件中如有侵權或不適當內容,請與我們聯系,我們立即糾正。
- 7. 本站不保證下載資源的準確性、安全性和完整性, 同時也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的傷害或損失。
最新文檔
- 2025年度文化遺址場地保護與利用合同協議書3篇
- 專業拓展訓練合作合同書2024版版B版
- 2024離婚雙方房產分割及過戶操作補充合同版B版
- 2024綜合授信額度合同及分期貸款細則版B版
- 2025年度廠房租賃及品牌授權合作協議3篇
- 2025年度工業廠房拆除及重建合同范本4篇
- 2025年度商業地產項目場地借用合同樣本3篇
- 2025年度數字化工廠搬遷工程合同范本4篇
- 油品基礎知識培訓課件
- 2024版室內粉刷工作班組勞動協議樣本版B版
- GB/T 20840.8-2007互感器第8部分:電子式電流互感器
- GB/T 14864-2013實心聚乙烯絕緣柔軟射頻電纜
- 品牌策劃與推廣-項目5-品牌推廣課件
- 信息學奧賽-計算機基礎知識(完整版)資料
- 發煙硫酸(CAS:8014-95-7)理化性質及危險特性表
- 數字信號處理(課件)
- 公路自然災害防治對策課件
- 火災報警應急處置程序流程圖
- 耳鳴中醫臨床路徑
- 安徽身份證號碼前6位
- 分子生物學在動物遺傳育種方面的應用
評論
0/150
提交評論