射線中英文報告

1、頁眉內容射線檢測評定記錄ZJN/8.6-19-2WeldRadiographicNegativeAssess TablePage 1 of1產品名稱Product Name材質Material片號焊縫號FilmWeld NoNo評片級別Evaluated class工作令號工件名稱Work NoPart Name厚度焊縫編號ThicknessWeld No缺陷性缺陷位置象質指備注缺陷量質Defect of Location黑度RemaDefectNo.of數 Wire150 150DensityrksTypeDefectIdentity評片 :日期 :復評 :日期Evaluated by:Da

2、te:Re-Evaluated by:Date:1 頁腳內容頁眉內容Exegesis: A-Crack( 裂紋 ). B-Lack of fusion( 未熔合 ). C-Lack of penetration( 未焊透 ). D-Rotundity-defect( 圓形缺陷 ). E-Strip-defect( 條狀缺陷 )焊縫射線檢測報告Radiographic Examination Report For Weld SeamZJN/8.6-19-1產品名稱工作令號Product NameJob No材質報告編號MaterialReport No源種類 Ir192CO60設備型號Type

3、of SourceEquip. Type焦點尺寸2*2膠片牌號Focus SizeFilm Brand增感方式前屏 Front0.03mm后屏 Back 0.1mm膠片規格PbFilm SizeIntensifying Means象質計型號/ 沖洗條件自動 Auto. 手工 ManualType of Image Quality IndicatorWashing Method檢顯影液配方天 山顯影條件5 Min,20Content of Developing LiquidDeveloping Condition測照相質量等級 ABB底片黑度2.0 4.0Illumination LevelFi

4、lm Density條焊縫編號 Seam No件板厚mm及Plate Thickness工透照方式Radiography Method藝 L1 （焦距）mm參數Focus To Film Distance能量 Energy(kV)管電流 Tube Current(源活度 Bq)mA曝光時間minLightening Time要求象質指數Required Image Quality Index焊縫長度(mm)Seam Length一次透照長度Once Radiographic Length合格級別（級）Qualified Level要求檢測比例%Required Test Ratio實際檢測比例

5、%Actual Test Ratio擴探比例%Extended Test Ratio檢測標準JB/T4730.2-2005檢測工藝編號JN/QD8.2-01-07Acc. StandardExam. Process No合格片數A 類焊縫B 類焊縫相交焊縫共 計最終評定結果級級級級Level ILevel IILevel IIILevel Qualified Film CategoriesACategories B Intersect PositionTotalFinalNumber張張張張Evaluating張張張張Results缺陷及返修情況說明檢測結果Specification For

6、Defect And RepairConclusion1.本臺產品返修片共計0 張，最高返修次數0 次2.超標缺陷部位返修后經復驗合格。3.返修部位原缺陷情況見焊縫射線檢測底片評定記錄。1.The total of repair for this product is 0 . The maximum repair at the same location is 0 times.2.After the defect repaired, retesting is qualified.3.The defect conditions of repairing location is referred

7、to the evaluating list of radiographic test film.1.本臺產品焊接一次合格率100 %。2.本臺產品焊縫質量符合III級的要求，結果合格。3.檢測位置及底片情況詳見焊縫射線底片評定記錄及射線檢測位置示意圖。1.The primary welding acceptance rate of this product is 100%2.The quality of theweld seam for this product confirms to the requirements ofthe applied level. The result is acceptance.3.The test locationand filmconditions are referred to the evaluation list ofradiographic testing film and the location sketch of radiographic test.2 頁腳內容頁眉內容報告人（資格）審核人（資格）無損檢測專用章年月日Reported byReviewed bySeal for NDEDate :年月日Date:年月日Date:無損檢測部位布置圖ZJN/8.6-18Examination Position Sche