華為交換機簡單配置大全.doc

華為交換機配置console口和telnet密碼實例 sys 進入到系統視圖Enter system view, return to user view with Ctrl+Z.Quidwayuser-interface aux 0Quidway-ui-aux0authentication-mode schemeNotice: Telnet or SSH user must be added , otherwise operator cant login!Quidway-ui-aux0quQuidwaylocal-user huawei 增加用戶名New local user added.Quidway-luser-huaweipassword simple huawei 配置密碼,且密碼不加密Quidway-luser-huaweiservice-type telnet ssh level 3 服務類型為SSH和telnet,且用戶登陸后權限為管理員權限Quidway-luser-huaweiquQuidwayuser-interface vty 0 4Quidway-ui-vty0-4authentication-mode schemeNotice: Telnet or SSH user must be added , otherwise operator cant login!Quidway-ui-vty0-4 save華為QuidWay交換機配置命令手冊：1、開始建立本地配置環境，將主機的串口通過配置電纜與以太網交換機的Console口連接。在主機上運行終端仿真程序（如Windows的超級終端等），設置終端通信參數為：波特率為9600bit/s、8位數據位、1位停止位、無校驗和無流控，并選擇終端類型為VT100。以太網交換機上電，終端上顯示以太網交換機自檢信息，自檢結束后提示用戶鍵入回車，之后將出現命令行提示符（如）。鍵入命令，配置以太網交換機或查看以太網交換機運行狀態。需要幫助可以隨時鍵入?2、命令視圖(1)用戶視圖(查看交換機的簡單運行狀態和統計信息):與交換機建立連接即進入(2)系統視圖(配置系統參數)Quidway:在用戶視圖下鍵入system-view(3)以太網端口視圖(配置以太網端口參數)Quidway-Ethernet0/1:在系統視圖下鍵入interface ethernet 0/1(4)VLAN視圖(配置VLAN參數)Quidway-Vlan1:在系統視圖下鍵入vlan 1(5)VLAN接口視圖(配置VLAN和VLAN匯聚對應的IP接口參數)Quidway-Vlan-interface1:在系統視圖下鍵入interface vlan-interface 1(6)本地用戶視圖(配置本地用戶參數)Quidway-luser-user1:在系統視圖下鍵入local-user user1(7)用戶界面視圖(配置用戶界面參數)Quidway-ui0:在系統視圖下鍵入user-interface3、其他命令設置系統時間和時區clock time Beijing add 8 clock datetime 12:00:00 2005/01/23設置交換機的名稱Quidwaysysname TRAIN-3026-1TRAIN-3026-1配置用戶登錄Quidwayuser-interface vty 0 4 Quidway-ui-vty0authentication-mode scheme創建本地用戶Quidwaylocal-user huawei Quidway-luser-huaweipassword simple huawei Quidway-luser-huawei service-type telnet level 34、VLAN配置方法配置環境參數SwitchA端口E0/1屬于VLAN2，E0/2屬于VLAN3組網需求把交換機端口E0/1加入到VLAN2 ，E0/2加入到VLAN3數據配置步驟VLAN配置流程(1)缺省情況下所有端口都屬于VLAN 1，并且端口是access端口，一個access端口只能屬于一個vlan；(2)如果端口是access端口，則把端口加入到另外一個vlan的同時，系統自動把該端口從原來的vlan中刪除掉；(3)除了VLAN1，如果VLAN XX不存在，在系統視圖下鍵入VLAN XX，則創建VLAN XX并進入VLAN視圖；如果VLAN XX已經存在，則進入VLAN視圖。【SwitchA相關配置】方法一：(1)創建（進入）vlan2 SwitchAvlan 2(2)將端口E0/1加入到vlan2 SwitchA-vlan2port ethernet 0/1(3)創建（進入）vlan3 SwitchA-vlan2vlan 3(4)將端口E0/2加入到vlan3 SwitchA-vlan3port ethernet 0/2方法二：(1)創建（進入）vlan2 SwitchAvlan 2(2)進入端口E0/1視圖 SwitchAinterface ethernet 0/1(3)指定端口E0/1屬于vlan2 SwitchA-Ethernet1port access vlan 2(4)創建（進入）vlan3 SwitchAvlan 3(5)進入端口E0/2視圖 SwitchAinterface ethernet 0/2(6)指定端口E0/2屬于vlan3 SwitchA-Ethernet2port access vlan 3測試驗證(1)使用命令disp cur可以看到端口E0/1屬于vlan2，E0/2屬于vlan3；(2)使用display interface Ethernet 0/1可以看到端口為access端口，PVID為2；(3)使用display interface Ethernet 0/2可以看到端口為access端口，PVID為35、交換機IP地址配置功能需求及組網說明配置環境參數三層交換機SwitchA有兩個端口ethetnet 0/1、ethernet 0/2，分別屬于vlan 2、vlan 3；以vlan 2的三層接口地址分別是1.0.0.1/24作為PC1的網關；以vlan 3的三層接口地址分別是2.0.0.1/24作為PC2的網關；組網需求PC1和PC2通過三層接口互通【SwitchA相關配置】(1)創建（進入）vlan2 Quidwayvlan 2(2)將端口E0/1加入到vlan2 Quidway-vlan2port ethernet 0/1(3)進入vlan2的虛接口 Quidway-vlan2interface vlan 2(4)在vlan2的虛接口上配置IP地址 Quidway-Vlan-interface2ip address 1.0.0.1 255.255.255.0(5)創建（進入）vlan3 Quidwayvlan 3(6)將E0/2加入到vlan3 Quidway-vlan3port ethernet 0/2(7)進入vlan3的虛接口 Quidway-vlan3interface vlan 3(8)在vlan3的虛接口上配置IP地址 Quidway-Vlan-interface3ip address 2.0.0.1 255.255.255.0測試驗證(1)PC1和PC2都可以PING通自己的網關(2)PC1和PC2可以相互PING通6、端口的trunk配置配置環境參數(1)SwitchA 端口E0/1屬于vlan10，E0/2屬于vlan20，E0/3與SwitchB端口E0/3互連(2)SwitchB 端口E0/1屬于vlan10，E0/2屬于vlan20，E0/3與SwitchA端口E0/3互連組網需求(1)要求SwitchA的vlan10的PC與SwitchB的vlan10的PC互通(2)要求SwitchA的vlan20的PC與SwitchB的vlan20的PC互通數據配置步驟【SwitchA相關配置】(1)創建（進入）vlan10 SwitchA vlan 10(2)將E0/1加入到vlan10 SwitchA-vlan10port Ethernet 0/1(3)創建（進入）vlan20 SwitchAvlan 20(4)將E0/2加入到vlan20 SwitchA-vlan20port Ethernet 0/2(5)實際當中一般將上行端口設置成trunk屬性，允許vlan透?jìng)?SwitchA-Ethernet0/3port link-type trunk(6)允許所有的vlan從E0/3端口透?jìng)魍ㄟ^(guò)，也可以指定具體的vlan值 SwitchA-Ethernet0/3port trunk permit vlan all【SwitchB相關配置】(1)創建（進入）vlan10 SwitchB vlan 10(2)將E0/1加入到vlan10 SwitchB-vlan10port Ethernet 0/1(3)創建（進入）vlan20 SwitchBvlan 20(4)將E0/2加入到vlan20 SwitchB-vlan20port Ethernet 0/2(5)實際當中一般將上行端口設置成trunk屬性，允許vlan透?jìng)?SwitchB-Ethernet0/3port link-type trunk(7)允許所有的vlan從E0/3端口透?jìng)魍ㄟ^(guò)，也可以指定具體的vlan值 SwitchB-Ethernet0/3port trunk permit vlan all【補充說明】(1)如果一個端口是trunk端口，則該端口可以屬于多個vlan；(2)缺省情況下trunk端口的PVID為1，可以在端口模式下通過命令port trunk pvid vlan vlanid 來修改端口的PVID；(3)如果從trunk轉發出去的數據報文的vlan id和端口的PVID一致，則該報文的VLAN信息會被剝?nèi)ィ@點在配置trunk端口時需要注意。(4)一臺交換機上如果已經設置了某個端口為hybrid端口，則不可以再把另外的端口設置為trunk端口。(5)一般情況下最好指定端口允許通過哪些具體的VLAN，不要設置允許所有的VLAN通過。測試驗證(1)SwitchA vlan10內的PC可以與SwitchB vlan10內的PC互通(2)SwitchA vlan20內的PC可以與SwitchB vlan20內的PC互通(3)SwitchA vlan10內的PC不能與SwitchB vlan20內的PC互通(4)SwitchA vlan20內的PC不能與SwitchB vlan10內的PC互通7、端口匯聚配置配置環境參數(1)交換機SwitchA和SwitchB通過以太網口實現互連。(2)SwitchA用于互連的端口為e0/1和e0/2，SwitchB用于互連的端口為e0/1和e0/2。組網需求增加SwitchA的SwitchB的互連鏈路的帶寬，并且能夠?qū)崿F(xiàn)鏈路備份，使用端口匯聚數據配置步驟【SwitchA交換機配置】(1)進入端口E0/1 SwitchAinterface Ethernet 0/1(2)匯聚端口必須工作在全雙工模式 SwitchA-Ethernet0/1duplex full(3)匯聚的端口速率要求相同，但不能是自適應 SwitchA-Ethernet0/1speed 100(4)進入端口E0/2 SwitchAinterface Ethernet 0/2(5)匯聚端口必須工作在全雙工模式 SwitchA-Ethernet0/2duplex full(6)匯聚的端口速率要求相同，但不能是自適應 SwitchA-Ethernet0/2speed 100(7)根據源和目的MAC進行端口選擇匯聚 SwitchAlink-aggregation Ethernet 0/1 to Ethernet 0/2 both 【SwitchB交換機配置】SwitchBinterface Ethernet 0/1SwitchB-Ethernet0/1duplex fullSwitchB-Ethernet0/1speed 100SwitchBinterface Ethernet 0/2SwitchB-Ethernet0/2duplex fullSwitchB-Ethernet0/2speed 100SwitchBlink-aggregation Ethernet 0/1 to Ethernet 0/2 both【補充說明】(1)同一個匯聚組中成員端口的鏈路類型與主端口的鏈路類型保持一致，即如果主端口為Trunk端口，則成員端口也為Trunk端口；如主端口的鏈路類型改為Access端口，則成員端口的鏈路類型也變?yōu)锳ccess端口。(2)不同的產品對端口匯聚時的起始端口號要求各有不同，請對照操作手冊進行配置。8、端口鏡像配置環境配置參數(1)PC1接在交換機E0/1端口，IP地址1.1.1.1/24(2)PC2接在交換機E0/2端口，IP地址2.2.2.2/24(3)E0/24為交換機上行端口(4)Server接在交換機E0/8端口，該端口作為鏡像端口組網需求(1)通過交換機端口鏡像的功能使用server對兩臺pc的業務報文進行監控。根據Quidway交換機不同型號，鏡像有不同方式進行配置：基于端口的鏡像 基于端口的鏡像是把被鏡像端口的進出數據報文完全拷貝一份到鏡像端口，這樣來進行流量觀測或者故障定位?；诹鞯溺R像 基于流鏡像的交換機針對某些流進行鏡像，每個連接都有兩個方向的數據流，對于交換機來說這兩個數據流是要分開鏡像的。S2008/S2016/S2026/S2403H/S3026等交換機支持的都是基于端口的鏡像 8016交換機支持基于端口的鏡像3500/3026E/3026F/3050支持基于流的鏡像 5516/6506/6503/6506R支持對入端口流量進行鏡像數據配置步驟以Quidway S3026C為例，通過基于二層流的鏡像進行配置：(1)定義一個ACL SwitchAacl num 200 (2)定義一個規則從E0/1發送至其它所有端口的數據包 SwitchArule 0 permit ingress interface Ethernet0/1 egress interface Ethernet0/2(3)定義一個規則從其它所有端口到E0/1端口的數據包 SwitchArule 1 permit ingress interface Ethernet0/2 egress interface Ethernet0/1(4)將符合上述ACL的數據包鏡像到E0/8 SwitchAmirrored-to link-group 200 interface e0/89、生成樹STP配置配置環境參數(1)交換機SwitchA、SwitchB和SwitchC都通過GE接口互連(2)SwitchB和SwitchC交換機是核心交換機，要求主備。組網需求 要求整個網絡運行STP協議數據配置步驟(1)【SwitchA交換機配置】 啟動生成樹協議: SwitchAstp enable(1)【SwitchB交換機配置】 啟動生成樹協議:SwitchBstp enable(3)配置本橋?yàn)楦鶚?SwitchBstp root primary (4)【SwitchC交換機配置】 a 啟動生成樹協議SwitchCstp enable b 配置本橋?yàn)閭浞莞鶚騍witchCstp root secondary(5)【SwitchD交換機配置】 a 啟動生成樹協議SwitchDstp enable【補充說明】(1)缺省情況下交換機的優先級都是32768，如果想人為指定某一臺交換機為根交換機，也可以通過修改優先級來實現；(2)缺省情況下打開生成樹后，所有端口都會開啟生成樹協議，請把接PC的端口改為邊緣端口模式；(3)如果要控制某條鏈路的狀態可以通過設置端口的cost值來實現。測試驗證(1)使用display stp查看交換機STP運行狀態(2)查看端口STP狀態display stp interface Ethernet XX是否正確10、Quidway交換機維護顯示系統版本信息：display version顯示診斷信息：display diagnostic-information 顯示系統當前配置：display current-configuration 顯示系統保存配置： display saved-configuration顯示接口信息：display interface顯示路由信息：display ip routing-table顯示VLAN信息：display vlan顯示生成樹信息：display stp顯示MAC地址表：display mac-address顯示ARP表信息：display arp顯示系統CPU使用率：display cpu顯示系統內存使用率：display memory顯示系統日志：display log 顯示系統時鐘：display clock驗證配置正確后，使用保存配置命令：save刪除某條命令，一般使用命令： undoS9306的入方向限速為：首先需要定義acl：acl number 3000Quidway-acl-advanced-3000rule permit ip 然后定義流分類，來匹配該acl：traffic classifier c1Quidway-classifier-c1if-match acl 3000 定義流動作，動作里面做限速的配置，此處限速1000kbits/s：舉例說明限速1Mtraffic behavior b1Quidway-behavior-b1 car cir 1000定義策略，把流行為和流動作關聯起來：traffic policy p1Quidway-trafficpolicy-p1classifier c1 behavior b1 進入端口下下發該策略既可：interface GigabitEthernet 0/0/1Quidway-GigabitEthernet0/0/1 traffic-policy p1 inboundS9306的出方向限速為： Quidway-Ethernet0/0/1 qos lr cir 1000 cbs 200000 注意：cbs=200*cir2M速率模板（inbound）acl number 3001Quidway-acl-advanced-3001rule permit iptraffic classifier 2mQuidway-classifier-2mif-match acl 3001traffic behavior 2mQuidway-behavior-2m car cir 2000traffic policy 2mclassifier 2m behavior 2m3M速率模板（inbound）acl number 3001rule permit iptraffic classifier 3mif-match acl 3001traffic behavior 3m car cir 3000traffic policy 3mclassifier 3m behavior 3m4M速率模板（inbound）acl number 3003Quidway-acl-advanced-3003rule permit iptraffic classifier 4mif-match acl 3001traffic behavior 4mcar cir 4000traffic policy 4mclassifier 4m behavior 4m6M速率模板（inbound）acl number 3004Quidway-acl-advanced-3004rule permit iptraffic classifier 6mif-match acl 3001traffic behavior 6mcar cir 6000traffic policy 6mclassifier 6m behavior 6m10M速率模板（inbound）acl number 3005Quidway-acl-advanced-3005rule permit iptraffic classifier 10mif-match acl 3001traffic behavior 10m car cir 10000traffic policy 10mclassifier 10m behavior 10m20M速率模板（inbound）acl number 3006Quidway-acl-advanced-3006rule permit iptraffic classifier 20mif-match acl 3001traffic behavior 20mcar cir 20000traffic policy 20mclassifier 20m behavior 20m30M速率模板（inbound）acl number 3007Quidway-acl-advanced-3007rule permit iptraffic classifier 30mif-match acl 3001traffic behavior 30mcar cir 30000traffic policy 30mclassifier 30m behavior 30m40M速率模板（inbound）acl number 3008Quidway-acl-advanced-3008rule permit iptraffic classifier 40mQuidway-classifier-40mif-match acl 3008traffic behavior 40mQuidway-behavior-40m car cir 40000traffic policy 40mQuidway-trafficpolicy-40mclassifier 40m behavior 40m45M速率模板（inbound）acl number 3009Quidway-acl-advanced-3009rule permit iptraffic classifier 45mQuidway-classifier-45mif-match acl 3009traffic behavior 45mQuidway-behavior-45m car cir 45000traffic policy 45mQuidway-trafficpolicy-45mclassifier 45m behavior 45m50M速率模板（inbound）acl number 3010Quidway-acl-advanced-3010rule permit iptraffic classifier 50mif-match acl 3001traffic behavior 50mcar cir 50000traffic policy 50mclassifier 50m behavior 50m100M速率模板（inbound）acl number 3011Quidway-acl-advanced-3011rule permit iptraffic classifier 100mQuidway-classifier-100mif-match acl 3011traffic behavior 100mQuidway-behavior-100m car cir 100000traffic policy 100mQuidway-trafficpolicy-100mclassifier 100m behavior 100m下行端口入方向應用（例如10M速率）interface GigabitEthernet 0/0/1Quidway-GigabitEthernet0/0/1 traffic-policy 10m inbound下行端口出方向1M速率Quidway-Ethernet0/0/1 qos lr cir 1000 cbs 2000002M速率Quidway-Ethernet0/0/1 qos lr cir 2000 cbs 4000003M速率Quidway-Ethernet0/0/1 qos lr cir 3000 cbs 6000004M速率Quidway-Ethernet0/0/1 qos lr cir 4000 cbs 8000005M速率Quidway-Ethernet0/0/1 qos lr cir 5000 cbs 10000006M速率Quidway-Ethernet0/0/1 qos lr cir 6000 cbs 120000010M速率Quidway-Ethernet0/0/1 qos lr cir 10000 cbs 200000020M速率Quidway-Ethernet0/0/1 qos lr cir 20000 cbs 400000030M速率Quidway-Ethernet0/0/1 qos lr cir 30000 cbs 600000040M速率Quidway-Ethernet0/0/1 qos lr cir 40000 cbs 800000045M速率Quidway-Ethernet0/0/1 qos lr cir 45000 cbs 900000050M速率Quidway-Ethernet0/0/1 qos lr cir 50000 cbs 10000000100M速率Quidway-Ethernet0/0/1 qos lr cir 100000 cbs 20000000S9306:S9306 display transceiver interface GigabitEthernet 1/0/1 verboseGigabitEthernet1/0/1 transceiver information:-Common information: Transceiver Type :1000_BASE_SX_SFP Connector Type :LC Wavelength(nm) :850 Transfer Distance(m) :500(50um),300(62.5um) Digital Diagnostic Monitoring :YES Vendor Name :FINISAR CORP. Ordering Name :-Manufacture information: Manu. Serial Number :PEH4HKB Manufacturing Date :2008-10-24 Vendor Name :FINISAR CORP.-Alarm information:-Diagnostic information: Temperature(C) :36 Voltage(V) :3.33 Bias Current(mA) :6.82 Bias High Threshold(mA) :23.85 Bias Low Threshold(mA) :1.73 RX Power(dBM) :-4.40 RX Power High Threshold(dBM) :0.00 RX Power Low Threshold(dBM) :-16.99 TX Power(dBM) :-4.53 TX Power High Threshold(dBM) :0.00 TX Power Low Threshold(dBM) :-9.50- +S8505:dis transceiver alarm interface GigabitEthernet 2/1/1GigabitEthernet2/1/1 transceiver current alarm information: RX Power Lowdis transceiver alarm interface GigabitEthernet 2/1/2GigabitEthernet2/1/2 transceiver current alarm information: Nonedis transceiver diagnosis interface GigabitEthernet 2/1/2Error: The transceiver does not support this function.+NE40E-X8dis interface GigabitEthernet 8/0/7GigabitEthernet8/0/7 current state : DOWNLine protocol current state : DOWNDescription:to_yanbuhengsheng_S9306_G6/0/0Route Port,The Maximum Transmit Unit is 1500Internet Address is 192.168.8.133/30IP Sending Frames Format is PKTFMT_ETHNT_2, Hardware address is 286e-d496-c271The Vendor PN is PT7420-51-EWThe Vendor Name is NEOPHOTONICSPort BW: 1G, Transceiver max BW: 1G, Transceiver Mode: SingleModeWaveLength: 1310nm, Transmission Distance: 40kmRx Power: -40.00dBm, Tx Power: -2.09dBmLoopback:none, full-duplex mode, negotiation: disable, Pause Flowcontrol:Receive Enable and Send EnableLast physical up time : -Last physical down time : 2010-10-21 17:12:33Statistics last cleared:never Last 300 seconds input rate: 0 bits/sec, 0 packets/sec Last 300 seconds output rate: 0 bits/sec, 0 packets/sec Input: 0 bytes, 0 packets Output: 0 bytes, 0 packets Input: Unicast: 0 packets, Multicast: 0 packets Broadcast: 0 packets, JumboOctets: 0 packets CRC: 0 packets, Symbol: 0 packets Overrun: 0 packets, InRangeLength: 0 packets+NE40E(8&x8)dis interface GigabitEth