EN60335-2-9A13和EK1的解釋.ppt

1、部門： 研究院測試認證中心 時間：2011年07月30日,EN60335-2-9:A13:2010+EK1 解釋,微波電器事業部,EN60335-2-9/A13:2010,1) EN 60335-2-9/A13:2010 Part 2-9: Particular requirements for grills, toasters and similar portable cooking appliance,發布期 DOP: 2011-10-01 強制實施期 DOW: 2013-10-01,2) EK1AG2 （以下簡稱EK1) Guidance for Implementation of CE

2、NELEC Guide 29 Test and Certification Decisions,發布期 DOP: 2011-07-01 強制實施期 DOW: 2011-10-01 凡需要獲得GS證書必須滿足EK1的要求！,EN60335-2-9/A13:2010,涉及小于18Kg的桌面微波爐，帶燒烤功能,一、結構更改 1）后背電源線插孔： 原因：,8.1.1 Test probe B and probe 18 of EN 61032 are applied without appreciable force, the appliance being in every possible posi

3、tion except that appliances normally used on the floor and having a mass exceeding 40 kg are not tilted. Through openings, the test probe is applied to any depth that the probe will permit and is rotated or angled before, during and after insertion to any position. If the opening does not allow the

4、entry of the probe, the force on the probe in the straight position is increased to 20 N when probe B is used or 10 N when probe 18 is used. If the probe then enters the opening, the test is repeated with the probe in the angled position. However when using test probe 18 the appliance shall be fully

5、 assembled as in normal operation without any parts removed; parts that are intended to be removed for user maintenance shall not be removed.使用測試指18的時候,期間在正常操作情況下測試. 任何可拆卸部件都不拆卸,EN60335-2-9/A13:2010,防危險運動部分的新的測試方法: 20.2Replace the first paragraph of compliance by: Compliance is checked by inspection

6、, by the tests of 21.1 and by means of: a test probe that is similar to test probe B of IEC 61032 but having a circular stop face with a diameter of 50 mm, instead of the non circular face, applied with a force of 5 N and test probe 18 of IEC 61032, applied with a force of 2,5 N.,Probe 18,Department

7、 name,2 August 2020,EN60335-2-9/A13:2010,EN60335-2-9/A13:2010,孔徑為10mm，Probe 18的可以插進去， 碰到運動的扇葉或高壓電容的帶電部分,EN60335-2-9/A13:2010,一、結構更改 2）門玻璃、頂部，左側，右側，后背： 原因：,11.Z101 Ovens, rotary grills, rotisseries and cookers are supplied at rated power and operated under normal operation. All heating units that can

8、 be connected to the supply mains at the same time during normal use are switched on. Ovens are operated without accessories. 測試方法：額定功率測試燒烤溫升, Ovens are operated with the door closed. Ovens having a thermostat are adjusted to its high setting. 溫升考核點：所有可以被Probe41,ProbeA(EK1)接觸的表面 Temperature rises ar

9、e not measured on the following surfaces,EN60335-2-9/A13:2010,1) surfaces on the oven door within 10 mm from the edge of the door (Zone 1); 2) surfaces around the oven door within 10 mm from the left right or lower edge of the door, or25 mm from the upper edge of the door (Zone 2); 3) surfaces withi

10、n 25 mm of vents (Zone 3); EK1僅豁免：Only the ventilation openings on the front side are exempted from the evaluation (ventilation of the muffle, zone 3(refer to picture Z102). 其他：The temperature rise around all other ventilation openings has to comply with the requirements of touchable surfaces (table

11、 Z.101). 4） underside surfaces that are not accessible with test probe 41, probe A(EK1) of EN 61032， 5) the rear surface of appliances which, according to the instructions, shall be placed against a wall; and are not accessible with test probe 41,probe A(EK1) of EN 61032，,EN60335-2-9/A13:2010,EN6033

12、5-2-9/A13:2010,Probe 41:,EN60335-2-9/A13:2010,Probe A:,EN60335-2-9/A13:2010,限值的對比:,請注意Note b!,EN60335-2-9/A13:2010,25mm豁免,10mm豁免,10mm豁免,Bare metal: 45K,Plastic: 65K,Glass: 60K,Bare metal: 45K (EK1:無通風口25mm豁免說法),EN60335-2-9/A13:2010,10mm豁免,10mm豁免,25mm豁免,Coated metal 55K,Coated metal 55K,判斷為Coated met

13、al前提是： Metal is considered coated when a coating having a minimum Thickness of 80um made by enamel or non substantially Plastic coating is used.,EN60335-2-9/A13:2010,10mm豁免,10mm豁免,25mm豁免,Coated metal 55K,Coated metal 55K,判斷為Coated metal前提是： Metal is considered coated when a coating having a minimum

14、Thickness of 80um made by enamel or non substantially Plastic coating is used.,EN60335-2-9/A13:2010,Coated metal 55K Bare metal 45K,在說明書有“the rear surface of appliances shall be placed against a wall”下,爐子底板部位， 若碰到則為 Coated metal 55K Bare metal 45K,EK1:,判斷為Coated metal前提是： Metal is considered coated

15、when a coating having a minimum Thickness of 80um made by enamel or non substantially Plastic coating is used.,EN60335-2-9/A13:2010,一、結構更改 3）器具的start/stop開關需要給用戶提供視覺和聽覺或者觸覺的反饋： 原因：,7.10 Addition: Devices used to start/stop operational functions of the appliance, if any, shall be distinguished from other manual devices by means of shape, or size, or surface texture, or position, etc. A tactile or an audible and visual feedback shall give an indication that the device has been operated.,EN60335