lesson 3.ppt

1、Lesson Three Text Diesel engine construction (II),A piston consists of a lower partpiston skirt(活塞裙) of cast iron and an upper part or crown(活塞頭) made of a special heat-resistant steel. They are bolted together and fixed to the piston rod.,1.Pistons and Piston rods,Piston crown,Piston skirt,Piston r

2、od,Piston ring,The position of the piston parts in relation to each other is secured by means of machine-turned recesses(凹槽) and a dowel pin(定位銷) in the crown.,Each piston is provided with five or six piston rings fitted in chromium plated grooves in the crown. The two or three topmost rings are nar

3、row rings having diagonal cuts(斜切口式), while the next two are broad and are provided with overlapping end joints.,The lowest ring is an oil distributor ring.,Diagonal cuts,Overlapping end joint,All the rings are slightly rounded on their external top and bottom edges to keep the oil film on the cylin

4、der liner during the running-in period(跑合期、磨合期) for new piston rings.,External top,External bottom,In order to control thermal stresses, thin-wall intensively cooled pistons(薄壁強制冷卻式活塞) are used for some types of modern engines.,In this case, the piston has an internal insert in the piston crown, whi

5、ch serves only to direct the cooling liquid flow and, thereby, to intensify the conventional cocktail shaker(振蕩冷卻) effect.,The piston rods are bored from the top flange to a point opposite the center of the crosshead(十字頭). Through this bore, a long pipe is inserted which goes nearly to the bottom of

6、 the bore.,Pipe,The outside diameter of the pipe is less than the diameter of the bore, the result being that an annular space is formed between the piston rod and the pipe.,Annular space,The lower end of each piston rod is reduced in diameter to fit a bore in the crosshead, this being secured to th

7、e piston rod by a nut. The piston rods are provided with dowel pins to ensure the correct assembly of the components.,Piston rod,Crosshead,On each of the two journals of the crosshead, crosshead shoes(十字頭滑板) are mounted which are guided in the built-in crosshead guides(十字頭導板) of the engine frame.,Cr

8、osshead,Crosshead shoe,Engine frame,Crosshead guide,The position of the crosshead shoes on the crosshead is determined by dowel pins. The guide shoes are secured to the crosshead by means of tap-bolts(錐體螺釘).,The crosshead shoes are white metal lined(白合金襯里), grooves being cut horizontally in the face

9、 of the white metal to ensure an adequate supply of lubricating oil.,The crosshead is short and rigid and the bearings are so constructed that the bearing pressure between the journal and bearing is distributed evenly over the entire length of the bearing.,In order to improve the working conditions

10、of the bearings, the bearing pressure is made smaller and the peripheral speed (is made) higher in later designs.,The pistons are cooled by oil supplied from the forced lubrication system.,The cooling oil is admitted through the pipe, from which the oil is led to the cooling spaces of the piston thr

11、ough telescopic pipes(伸縮管) or articulated pipe(鉸接管), and round the internal pipes of the piston rods.,The cooling oil is conducted from the piston through the internal pipes of the piston rods and the ducts in the crossheads, as well as the slotted pipes from which the oil is led to “control boxes”

12、with sight glasses(觀察鏡) on the engine.,Sealing between the crankcase and scavenging air boxes is achieved by means of the piston rod stuffing boxes, located in the bottom of the scavenging air boxes. Each stuffing is provided with two sealing rings and three scraper rings.,The sealing rings, which a

13、re mounted uppermost are in four parts and pressed together around the piston rods by means of coil springs(盤簧).,Connecting Rod and Main Bearings The crosshead and crankpin bearings (曲柄銷軸承) are made of cast steel and each consist of an upper and a lower part secured to the connecting rod by means of

14、 fitted bolts(拂配螺栓), the nut of which are secured.,The bearings have white metal bearing surfaces provided with lubrication grooves for the necessary supply of lubricating and cooling oil.,Shims(墊片,調整片) of different thickness are inserted between the shells to enable adjustment of the bearing cleara

15、nces (approx. 0.20-0.30mm).,The main bearings, which support the crankshaft, each consist of two shells of cast steel with white metal bearing surfaces having lubricating grooves of an appropriate shape.,The shells are secured by means of bearing caps and studs, the necessary clearance (approx. 0.30

16、mm) being provided by means of shims of different thickness.,All bearings are lubricated from the force-feed lubrication system of the engine, the oil being supplied partly through pipes to each main bearing cap and partly to the crosshead, from where the lubricating oil flows through channels to th

17、e crankpin bearings.,3. Crankshaft,Flywheel 飛輪,曲柄銷 Crankpin,曲柄臂 Crank throw(web),Main bearing journal 主軸頸,The crankshafts are built up types(組合式). For semi-built type(半組合式), the forged main bearing journals are shrunk(紅套) into cast steel crank throws with a crank journal and two crank throws as one

18、unit.,In the fully built type(全組合式), the crank throws are shrunk on to main journals and crank journals. The crank throws are displaced from each other to obtain the same number of degrees between the different crank throws.,The crankpin journals are provided with large bores for balancing purpose.,

19、Reading Material M.A.N. Marine diesel engine,The latest large bore two stroke M.A.N. engine is the KSZ 90/160B series in cylinder numbers from 6 to 12 and developing 2,700 K.W. (3,672H.P.)/cyl.,The engine operates at 122 rev/min. with an M.E.P.(mean effective pressure平均有效壓力) of 13 bar and a mean pis

20、ton speed of 6.5m/sec.,The bedplate is of fabricated design and consists of two I-shaped longitudinal girders with transverse members into which the cast steel bearing housings are welded.,The thrust bearing casing is incorporated into the bedplate.,Columns(機架) have been replaced by frames construct

21、ed of box shaped longitudinal girders. The fabricated top and bottom sections run the full length of the engine and are mounted on the bedplate.,Such an engine frame helps to stiffen the engine and so protect the bearings from the deformation forces transmitted(傳遞) via the ships double bottom.,The c

22、ast iron guideways(導板) for the crosshead are attached to the top section and seal off the crankcase.,The cylinder jackets are individual castings(鑄件) bolted together to form one continuous member.,The one-piece cylinder liners are fitted into the jackets from the top and a cast steel strong back is

23、fitted in way of the combustion space to help absorb gas forces.,*The scavenge process is the M.A.N. loop system(回流掃氣系統) and the scavenge and exhaust ports are arranged in two tiers and are carried far around the liner.,The vertical lands between the ports are cooled by water passing through cast in

24、 tubes and thence to passages arranged around the liner above the exhaust ports.,Each cylinder cover is in two parts, the lower section is of special thin walled forged steel permitting the area in way of the combustion gases to be intensively cooled whilst absorbing thermal stresses,and this is hel

25、d in position by an upper supporting unit of cast iron, which transmits the gas forces to the cylinder jackets via long studs.,The joint face between the cylinder cover and the liner is arranged as far away from the combustion process as possible.,The gas loads on the engine structure are constraine

26、d(約束) by means of hydraulically(液壓的) preloaded tie rods which connect the bedplate, frame sections and cylinder jackets into a single unit.,The crankshaft is of the semi built type, with the journal being shrunk into the forged or cast steel crank throws.,With the exception of the six-cylinder engin

27、e, it(crankshaft) is in two parts joined by fitted bolts.,The coupling flange(聯接法蘭) for attachment to the propeller shaft also accommodates the turning gear(盤車機) and is integrally forged with the crankshaft.,The aft end section also incorporates a thrust collar(推力環).,The drive for the camshaft gear

28、train is taken from a spur gear(正齒輪) which for a six cylinder engine is at the coupling end and for 7 to 12 cylinder engines the drive is located in the middle of the engine.,The piston crown is of forged steel and is designed for intensive cooling, the central supporting body is of cast steel and i

29、s mainly subjected to compressive stress.,The two components are bolted together and connected to the piston rod. A single piece piston skirt fitted with bronze(青銅) rings guides the piston in the cylinder liner.,The piston ring grooves for a standard engine are flame hardened(淬火，硬化) against wear. Th

30、e crosshead pin bearings are white metal lined shells lubricated by means of high-pressure pumps.,The piston forces are transmitted over the entire length of the crosshead pin then to the connecting rod via the lower half single bearing shell.,The principle of hydrostatic lubrication （液體靜壓潤滑）has bee

31、n applied to the crosshead using high-pressure lubricators.,This is achieved by means of high pressure pumps with two plungers and rods operated by the oscillating(振蕩) movement of the connecting rod,high pressure oil is delivered to the lower part of the crosshead bearing, the pumps press oil into t

32、he bearing when the load on the shell is at its lowest.,This ensures that the oil film is maintained at all times and on all loads between the journal and the shell.,Scavenging of the cylinder liner is on the loop scavenge system and constant pressure of the exhaust gas is used to drive the turbocha

33、rgers.,During running up(起動) and in the lower partial load range the turbochargers are assisted by electrically driven auxiliary blowers connected before the compressors of the main blowers.,In the upper power range the auxiliary blowers are disconnected. Diffusers(擴壓器) are fitted in the exhaust sys

34、tem and facilitate charge removal and scavenging in each cylinder.,The diffuser also prevents pressure pulse from one cylinder interfering with another during operation.,B. MAN-B&W MC ENGINE,MAN-B&W K 90MC-C engine is a large crosshead type two-stroke engine with a bore of 900 mm, a 2,300 mm stroke

35、and an operating speed of 104 r/min. It is constructed with between six and twelve cylinders.,Developed as one of the extensive range of the manufacturers MC engines, it is of the power and speed best suited to large, fast container ships. The increase in running speed is obtained by a slight decrea

36、se in engine stroke.,High thermal efficiency is maintained by an increase in mean effective pressure(M.E.P).,Construction can be considered generally as typical for the whole range.,The engine bedplate is of rigid box form,fabricated from steel plates with main bearing supports of cast steel .,Welde

37、d Aframes are assembled into a frame box which contains the crankcase, the crosshead guides and also supports the wheels for the chain drive of the camshaft.,A cast iron cylinder frame accommodates the scavenge space between the cylinder jacket and the diaphragm(橫隔板）, both of which are water-cooled.

38、,Long pre-stressed tie bolts are fitted between the top of the frame and the underside of the bedplate girders.,The cylinder liner is of alloy cast iron, its upper flange lands on top of the frame and has bore cooling.,It is secured by a forged steel cylinder cover which is also bore cooled and shap

39、ed internally to accommodate most of the combustion space.,Cylinder lubricating oil is injected at one level in the liner.,Piston have a chrome-molybdenum alloy steel(鉻鉬合金鋼） crown with hard chrome-surfaced(plated)（表面鍍鉻） ring grooves in which four compression rings are fitted.,In this particular mode

40、l a protective layer of inconel(鉻鎳鐵合金） is welded to part of the crown surface to prevent high temperature corrosion.,The piston is oil cooled, oil being supplied by a telescopic pipe to the crosshead and then through the piston rod.,It is returned from the crosshead to a slotted pipe in the crankcas

41、e. A short cast iron skirt is added. The crown is bolted to the piston rod at an inner support ring.,Surface hardening reduces wear on the piston rod at the diaphragm gland.,The rod is bolted at the top of a cylindrical crosshead which is of large diameter and incorporates a full-length bottom half-

42、bearing shell. Floating guide shoes are attached at each end.,The crankshaft may be either semi-built up or of welded construction, with large journal and pins. All crankcase bearings are of white metal.,Main bearings have thick(wall) shells, crankpin(bottom end)and crosshead(top end ) bearing have

43、thin-wall shells. White metal is used for the guide surface.,The exhaust valves are operated by hydraulically under oil pressure from cam-timed actuated pistons. They have air compressed springs which allows them to be rotated by vanes.,The valve spindles are usually manufactured by the hot isostati

44、c(均衡的) pressure(HIP) method熱均壓法, a compound Nimonic(鎳鉻鈦合金) and austenitic(奧氏體的) steel part construction.,Valve housing（閥殼） is cooled at its seat and spindle guide bush（導套） but its upper duct is uncooled to avoid low temperature corrosion.,Fuel pumps are cam driven and timed by the plunger helix(螺旋槽)

45、.,An adjustable barrel(套筒) allows variable ignition timing to maintain combustion efficiency at low speed and can be adjusted to match the ignition quality of fuels.,Pumping timing is changed for astern operation by a link connected at the cam roller guide which is activated by compressed air.,Each

46、pump supplies three identical fuel injectors for the corresponding unit. Injectors are uncooled but they circulate hot fuel directly while their needle valves are in the closed position.,The engine operates with a constant pressure system, with uncooled turbochargers. Two auxiliary blowers are fitte

47、d to operate at low charge air pressure or at low engine revolutions.,A number of waste heat recovery(余熱回收裝置) and power take-off systems(取力系統) can be operated under running conditions.,c. VIBRATION DAMPER減振器,The vibration damper serves to reduce the torsional(扭轉的)vibration generated by the crankshaft. The damper consists of a housing and a free rotating inertia ring supported by an axial bearing.,It forms a to