中國塑料標準

1、中國塑料標準(GB plastic standards)ANSI| BS| DIN| EN| GB| ISO| JIS| NF| DIC編號中文名稱英文名稱BB/T 0025-2004聚三氟氯乙烯塑料襯里截止閥()BB/T 0043-2007塑料物流周轉箱()BB/T 0044-2007包裝容器 塑料農藥瓶()CP 312-1-1973塑料管道(熱塑材料)實用規程.第1部分:一般原理和材料選擇Code of practice for plastics pipework (thermoplastics materia

2、l). General principles and choice of materialCP 312-2-1973塑料管道(熱塑材料)實用規程.第2部分:壓力液體輸送用非增塑PVC管Code of practice for plastics pipework (thermoplastics material). Unplasticized PVC pipework for the conveyance of liquids under pressureDD ENV 1401-2-2001非壓力地下廢水排放和污水系統的塑料管道系統.非增塑聚氯乙烯.符合性評定指南Plastics piping

3、systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinylchloride) (PVC-U). Guidance for assessment of conformityDD ENV 1452-6-2002供水用塑料管道系統.未增塑聚氯乙烯(PVC-U).安裝指南Plastics piping systems for water supply. Unplasticized poly(vinyl chloride) (PVC-U). Guidance for installationDL

4、/T 622-1997(2005)立式水輪發電機彈性金屬塑料推力軸瓦技術條件()DL/T 742-2001冷卻塔塑料部件技術條件()DL/T 802.2-2007電力電纜用導管技術條件 第2部分：玻璃纖維增強塑料電纜導管Technical requirements for electric cable conduits Part 2:Cable conduits of fiberglass reinforced plasticsDL/T 802.3-2007電力電纜用導管技術條件 第3部分：氯化聚氯乙烯及硬聚氯乙烯塑料電纜導管Technical requirements for electri

5、c cable conduits Part 3:Cable conduits of chlorinated polyvinyl chloride and unplasticized polyvinyl chlorideDL/T 802.4-2007電力電纜用導管技術條件 第4部分：氯化聚氯乙烯及硬聚氯乙烯塑料雙壁波紋電纜導管Technical requirements for electric cable conduits Part 4:Double wall corrugated cable conduits of chlorinated polyvinyl chloride and unp

6、lasticized polyvinyl chlorideFZ 93004-1991紡紗和捻線用塑料鉤()FZ 93010-1991換梭式梭子用塑料緯紗管()FZ/T 90003.1-1991塑料經紗管和緯紗管試驗方法靜彎曲()FZ/T 90003.2-1991塑料經紗管和緯紗管試驗方法沖擊功()FZ/T 90003.3-1991塑料經紗管和緯紗管試驗方法振幅()FZ/T 90080.1-1995紡織用塑料投梭結試驗方法 球壓痕硬度()FZ/T 90080.2-1995織機用塑料投梭結試驗方法 沖擊強度()FZ/T 92044-1995酚醛塑料槽筒()FZ/T 93004-2002(2009)

7、紡紗和捻線用塑料鉤()FZ/T 93008-2002(2009)環錠細沙機用塑料經紗管()FZ/T 93010-2002(2009)換梭式梭子用塑料緯紗管()FZ/T 93029-1994塑料粗紗管()FZ/T 94017-1994長絲絡并捻用塑料雙邊筒管()FZ/T 94030-1995棉織機用塑料投梭結()FZ/T 94031-1995毛織機用塑料投梭結()FZ/T 94032-1995麻織機用塑料投梭結()FZ/T 94033-1995多梭箱絲織機用塑料投梭結()FZ/T 96014-1993簾子線捻線用塑料雙邊筒管()GB 10457-2009食品用塑料自粘保鮮膜Plastic cli

8、ng wrap film for keeping fresh of foodGB 13454-1992氨基模塑料Plastics-Aminoplastic moulding materials-SpecificationGB 1404.3-2008塑料 粉狀酚醛模塑料 第3部分：選定模塑料的要求Plastics - Phenolic powder moulding compounds - Part 3: Requirements for selectes moulding compoundsGB 14232.1-2004人體血液及血液成分袋式塑料容器第1部分:傳統型血袋Plastics col

9、lapsible containers for human blood and blood components-Part1:Conventional containersGB 15593-1995輸血(液)器具用軟聚氯乙烯塑料Plasticized polyvinyl chloride (PVC) compounds for transfusion (infusion) equipmentGB 16487.12-2005進口可用作原料的固體廢物環境保護控制標準廢塑料Environmental protection control standard for imported solid was

10、tes as raw materials - Waste and scrap of plasticsGB 18006.1-2009塑料一次性餐飲具通用技術要求General requirement of plastic disposable tablewareGB 18072-2000塑料廠衛生防護距離標準Health protection zone standard for plastics plantGB 18191-2008包裝容器 危險品包裝用塑料桶Packing containers - Plastic drum for packages of dangerous goodsGB 1

11、9160-2008包裝容器 危險品包裝用塑料罐Packing containers - Plastic jerrican for packages of dangerous goodsGB 19434.8-2004危險貨物剛性塑料中型散裝容器檢驗安全規范性能檢驗Safety code for theinspection of rigid plastics IBCs for dangerous goods-Performance testsGB 19741-2005液體食品包裝用塑料復合膜、袋The plastics laminated films and bags using for pack

12、aging of liquid foodGB 20265-2006耐化學品的工業用模壓塑料靴Moulded plastics industrial boots with chemical resistanceGB 21660-2008塑料購物袋的環保、安全和標識通用技術要求The general requirement for environmental protection, safety, identification and marking of plastic shopping bagsGB 22530-2008橡膠塑料注射成型機安全要求Safety requirements of i

13、njection moulding machines for rubber and plasticsGB/T 10004-2008包裝用塑料復合膜、袋 干法復合、擠出復合Plastic laminated films & pouches for packaging dry lamination & extrusion laminationGB/T 10006-1988塑料薄膜和薄片摩擦系數測定方法Plastics-Film and sheeting-Determination of the coefficients of frictionGB/T 10007-2008硬質泡沫塑

14、料 剪切強度試驗方法Rigid cellular plastics - Determination of shear strengthGB/T 10009-1988丙烯腈-丁二烯-苯乙烯(ABS)塑料擠出板材Acrylenitrile-butadiene-styrene (ABS) plastics extrusion platesGB/T 1033.1-2008塑料 非泡沫塑料密度的測定 第1部分：浸漬法、液體比重瓶法和滴定法Plastics - Methods for determining the density of non-cellular plastics - Part 1: Im

15、mersion method, liquid pyknometer method and titration methodGB/T 1034-2008塑料 吸水性的測定Plastics - Determination of water absorptionGB/T 1036-2008塑料 -3030線膨脹系數的測定 石英膨脹計法Test method for coefficient of linear thermal expansion of plastics between -30 and 30 with a vitreous silica dilatometerGB/T 1037-1988

16、塑料薄膜和片材透水蒸氣性試驗方法杯式法Test method for water vapor transmission of plastic film and sheet-Cup methodGB/T 1038-2000塑料薄膜和薄片氣體透過性試驗方法壓差法Plastics-Film and sheeting-Determination of gas transmission-Differential-pressure methodGB/T 1040.1-2006塑料拉伸性能的測定第1部分：總則Plastics - Determination of tensile properties - P

17、art 1: General principlesGB/T 1040.2-2006塑料拉伸性能的測定第2部分：模塑和擠塑塑料的試驗條件Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plasticsGB/T 1040.3-2006塑料拉伸性能的測定第3部分：薄膜和薄片的試驗條件Plastics - Determination of tensile properties - Part 3: Test conditions for films an

18、d sheetsGB/T 1040.4-2006塑料拉伸性能的測定第4部分：各向同性和正交各向異性纖維增強復合材料的試驗條件Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic compositesGB/T 1040.5-2008塑料 拉伸性能的測定 第5部分：單向纖維增強復合材料的試驗條件Plastics - Determination of tensile properties - Part

19、 5: Test conditions for unidirectional fibre-reinforced plastic compositesGB/T 1041-2008塑料 壓縮性能的測定Plastics - Detemination of compressive propertiesGB/T 1043.1-2008塑料 簡支梁沖擊性能的測定 第1部分：非儀器化沖擊試驗Plastics - Determination of charpy impact properties - Part 1: Non - instrumented impact testGB/T 10798-2001熱塑

20、性塑料管材通用壁厚表Thermoplastics pipes-Universal wall thickness tableGB/T 10799-2008硬質泡沫塑料 開孔和閉孔體積百分率的測定Rigid cellular plastics - Determination of the volume percentage of open cells and of closed cellsGB/T 10801.1-2002絕熱用模塑聚苯乙烯泡沫塑料Moulded polystyrene foam board for thermal insulationGB/T 10801.2-2002絕熱用擠塑聚

21、苯乙烯泡沫塑料(XPS)Rigid extruded polystyrene foam board for thermal insulation (XPS)GB/T 10802-2006通用軟質聚醚型聚氨酯泡沫塑料General flexible polyether polyurethane cellular plasticsGB/T 11016.1-2009塑料絕緣和橡皮絕緣電話軟線 第1部分：一般規定Plastic or rubber insulated telephone cords - Part 1: GeneralGB/T 11016.2-2009塑料絕緣和橡皮絕緣電話軟線 第2部分

22、：聚氯乙烯絕緣電話軟線Plastic or rubber insulated telephone cords - Part 2: Polyvinyl chloride insulated telephone cordsGB/T 11016.3-2009塑料絕緣和橡皮絕緣電話軟線 第3部分：聚丙烯絕緣電話軟線Plastic or rubber insulated telephone cords - Part 3: Polypropylene insulated telephone cordsGB/T 11016.4-2009塑料絕緣和橡皮絕緣電話軟線 第4部分：橡皮絕緣電話軟線Plastic o

23、r rubber insulated telephone cords - Part 4: Rubber insulated telephone cordsGB/T 11546.1-2008塑料 蠕變性能的測定 第1部分：拉伸蠕變Plastic - Determination of creep behaviour - Part 1: Tensile creepGB/T 11547-2008塑料 耐液體化學試劑性能的測定Plastic - Methods of test for the determination of the effects of immersion in liquid chem

24、icalsGB/T 11548-1989硬質塑料板材耐沖擊性能試驗方法 (落錘法)Standard test method for impact resistance of rigid plastic sheeting by means of a tup (falling weight)GB/T 11793-2008未增塑聚氯乙烯（PVC-U）塑料門窗力學性能及耐候性試驗方法Test methods on mechanical and weathering properties for unplasticized polyvinyl chloride (PVC-U) doors and win

25、dowsGB/T 11997-2008塑料 多用途試樣Plastic - Multipurpose test specimensGB/T 11998-1989塑料玻璃化溫度測定方法熱機械分析法Determination of glass transitiontemperature of plastics-Thermomechanical analysisGB/T 12000-2003塑料暴露于濕熱、水噴霧和鹽霧中影響的測定Determination of the effects of exposure to damp heat，water spray and salt mist for pla

26、sticsGB/T 12001.1-2008塑料 未增塑聚氯乙烯模塑和擠出材料 第1部分：命名系統和分類基礎Plastics - Unplasticized poly (vinyl chloride) (PVC-U) moulding and extruded materials - Part 1: Designation system and basis for specificationsGB/T 12001.2-2008塑料 未增塑聚氯乙烯模塑和擠出材料 第2部分：試樣制備和性能測定Plastics - Unplasticized poly (vinyl chloride) (PVC-U

27、) moulding and extruded materials - Part 2: Preparation of test specimens and determination of propertiesGB/T 12002-1989塑料門窗用密封條Sealing strips for plastic doors and windowsGB/T 12003-2008未增塑聚氯乙烯（PVC-U）塑料窗 外形尺寸的測定Unplasticized polyvinyl chloride(PVC-U) windows - Determination of dimensionsGB/T 12006.

28、1-2009塑料 聚酰胺 第1部分：黏數測定Plastics - Polyamides - Part 1: Determination of viscosity numberGB/T 12006.2-2009塑料 聚酰胺 第2部分：含水量測定Plastics - Polyamides - Part 2: Determination of water contentGB/T 12008.1-2009塑料 聚醚多元醇 第1部分：命名系統Plastics - Polyether polyols - Part 1: Designation systemGB/T 12008.3-2009塑料 聚醚多元醇

29、 第3部分：羥值的測定Plastics - Polyether polyols - Part 3: Determination of hydroxyl numberGB/T 12008.4-2009塑料 聚醚多元醇 第4部分：鈉和鉀的測定Plastics - Polyether polyols - Part 4: Determination of sodium and potassiumGB/T 12009.3-2009塑料 多亞甲基多苯基異氰酸酯 第3部分：黏度的測定Plastics - Polymethylene polyphenyl isocyanate - Part 3: Determ

30、ination of viscosityGB/T 12010.1-2008塑料聚乙烯醇材料（PVAL） 第1部分：命名系統和分類基礎Plastics - Poly(vinyl alcohol)(PVAL) materials - Part 1: Designation system and basis for specificationsGB/T 12027-2004塑料薄膜和薄片加熱尺寸變化率試驗方法Plastics-Film and sheeting-Determination of dimensional change on heatingGB/T 12554-2006塑料注射模技術條件

31、Specifiication of injection moulds for plasticsGB/T 12555-2006塑料注射模模架Injection mould bases for plasticsGB/T 12556-2006塑料注射模模架技術條件Specification of injection mould bases for plasticsGB/T 12584-2008橡膠或塑料涂覆織物 低溫沖擊試驗Rubber or plastics coated fabrics - Low-temperature impact testGB/T 12586-2003橡膠或塑料涂覆織物耐屈

32、撓破壞性的測定Rubber or plastics-coated fabrics-Determination of resistance to damage by flexingGB/T 12587-2003橡膠或塑料涂覆織物抗壓裂性的測定Rubber or plastics-coated fabrics-Determination of crush resistanceGB/T 12588-2003塑料涂覆織物聚氯乙烯涂覆層融合程度快速檢驗法Plastics coated fabrics-Polyvinyl chloride coatings-Rapid method for checkin

33、g fusionGB/T 12600-2005金屬覆蓋層塑料上鎳+鉻電鍍層Metallic coatings Electroplated coatings of nickel plus chromium on plastics materialsGB/T 12722-2008橡膠和塑料軟管組合件 液壓脈沖曲撓試驗（半試驗）Rubber and plastics hose assemblies - Flexing combined with hydraulic impulse test（half-omega test）GB/T 12783-2000橡膠塑料機械產品型號編制方法Editorial

34、nominating method for the modeldesignation of rubber and plastics machineryGB/T 12784-1991橡膠塑料加壓式捏煉機Dispersion mixer for rubber and plasticsGB/T 12811-1991硬質泡沫塑料平均泡孔尺寸試驗方法Test method for average cell size of rigid cellular plasticsGB/T 12812-2006硬質泡沫塑料 易碎性的測定Rigid cellular plastics - Determination o

35、f friabilityGB/T 12833-2006橡膠和塑料撕裂強度和粘合強度測定中的多峰曲線分析Rubber and plastics - Analysis of multipeak traces obtained in determinations of tear strength and adhesion strengthGB/T 12949-1991滑動軸承覆有減摩塑料層的雙金屬軸套Plain bearings-Bimetallic busheswith plastic overlayGB/T 13096-2008拉擠玻璃纖維增強塑料桿力學性能試驗方法Test method for

36、 mechanical properties of pultruded glass fiber reinforced plastic rodsGB/T 13376-2008塑料閃爍體Plastic scintillatorsGB/T 13455-1992氨基模塑料揮發物測定方法Plastics-Aminoplastic moulding materials-Determination of volatile matterGB/T 13525-1992塑料拉伸沖擊性能試驗方法Test method for tensile-impact property of plasticsGB/T 13578

37、-1992橡膠塑料壓延機Rubber and plactics calenderGB/T 13947-1992電子元器件塑料封裝設備通用技術條件General specification for electronic components plastic packaging equipmentsGB/T 1404.1-2008塑料 粉狀酚醛模塑料 第1部分: 命名方法和基礎規范Plastics - Phenolic powder moulding compounds - Part 1: Designation system and basis for specificationsGB/T 14

38、04.2-2008塑料 粉狀酚醛模塑料 第2部分: 試樣制備和性能測定Plastics - Phenolic powder moulding compounds - Part 2: Preparation of test specimens and determination of propertiesGB/T 14112-1993半導體集成電路塑料雙列封裝沖制型引線框架規范Semiconductor integrated circuits-Specification for stamped leadframes of plastic DIPGB/T 14152-2001熱塑性塑料管材耐外沖擊

39、性能試驗方法時針旋轉法Thermoplastics pipes-Determination of resistance to external blows-Round-the-clock methodGB/T 14153-1993硬質塑料落錘沖擊試驗方法通則General test method for impact resistance of rigid plastics by means of falling weightGB/T 14154-1993塑料門垂直荷載試驗方法Plastics doors-Vertical load testGB/T 14208.1-2009紡織玻璃纖維增強塑

40、料 無捻粗紗增強樹脂棒機械性能的測定 第1部分：通則和棒的制備Textile-glass-reinforced plastics - Determination of mechanical properties on rods made of roving-reinforced resin - Part 1: General considerations and preparation of rodsGB/T 14208.2-2009紡織玻璃纖維增強塑料 無捻粗紗增強樹脂棒機械性能的測定 第2部分：彎曲強度的測定Textile-glass-reinforced plastics - Deter

41、mination of mechanical properties on rods made of roving- reinforced resin - Part 2: Determination of flexural strengthGB/T 14208.3-2009紡織玻璃纖維增強塑料 無捻粗紗增強樹脂棒機械性能的測定 第3部分：壓縮強度的測定Textile-glass-reinforced plastics - Determination of mechanical properties on rods made of roving- reinforced resin - Part 3

42、: Determination of compressive strengthGB/T 14208.4-2009紡織玻璃纖維增強塑料 無捻粗紗增強樹脂棒機械性能的測定 第4部分：表觀層間剪切強度的測定Textile-glass-reinforced plastics - Determination of mechanical properties on rods made of roving-reinforced resin - Part 4: Determination of apparent interlaminar shear strengthGB/T 14216-2008塑料 膜和片潤

43、濕張力的測定Plastics - Film and sheeting - Determination of wetting tensionGB/T 14234-1993塑料件表面粗糙度Surface roughness for plastic partsGB/T 14447-1993塑料薄膜靜電性測試方法半衰期法Test method for electrostatic properties of plastic films-Half-life methodGB/T 1446-2005纖維增強塑料性能試驗方法總則Fiber-reinforced plastics composites-The

44、generals for determination of propertiesGB/T 1447-2005纖維增強塑料拉伸性能試驗方法Fiber-reinforced plastics composites-Determination of tensile propertiesGB/T 1448-2005纖維增強塑料壓縮性能試驗方法Fiber-reinforced plastics composites-Determination of compressive propertiesGB/T 14484-2008塑料 承載強度的測定Plastics - Determination of bea

45、ring strengthGB/T 14486-2008塑料模塑件尺寸公差Dimensional tolerances for moulded plastic partsGB/T 1449-2005纖維增強塑料彎曲性能試驗方法Fibre-reinforced plastic composites-Determination of flexural propertiesGB/T 1450.1-2005纖維增強塑料層間剪切強度試驗方法Fibre-reinforced plastic composites-Determination of interlaminar shear strengthGB/

46、T 1450.2-2005纖維增強塑料沖壓式剪切強度試驗方法Fibre-reinforced plastic composites-Determination of the punch-type shear strengthGB/T 1451-2005纖維增強塑料簡支梁式?jīng)_擊韌性試驗方法Fiber-reinforced plastics composites-Determination of Charpy impact propertiesGB/T 14519-1993塑料在玻璃板過濾后的日光下間接曝露試驗方法Plastics-Method of exposure to indirect we

47、athering using glass-filtered daylightGB/T 14520-1993氣相色譜分析法測定不飽和聚酯樹脂增強塑料中的殘留苯乙烯單體含量Determination of residual styrene monomer content in reinforced plastics based on unsaturated polyester resins by gas chromatographyGB/T 14522-2008機械工業產品用塑料、涂料、橡膠材料人工氣候老化試驗方法 熒光紫外燈Artificial weathering test method fo

48、r plastics,coating and rubber materials used for machinery industrial products - Fluorescent UV lampsGB/T 1458-2008纖維纏繞增強塑料環形試樣力學性能試驗方法Test method for mechanical properties of ring of filament-winding reinforced plasticsGB/T 1462-2005纖維增強塑料吸水性試驗方法Test methods for water absorption of fiber reinforced

49、 plasticsGB/T 1463-2005纖維增強塑料密度和相對密度試驗方法Test methods for density and relative density of fiber reinforced plasticsGB/T 14904-1994鋼絲增強的橡膠、塑料軟管和軟管組合件屈撓液壓脈沖試驗Rubber and plastics hose and hose assemblies-Wire reinforced-Hydraulic impulse test with flexingGB/T 14905-2009橡膠和塑料軟管 各層間粘合強度的測定Rubber and plast

50、ics hoses - Determination of adhesion between componentsGB/T 15047-1994塑料扭轉剛性試驗方法Test method for stiffness proporties in torsion of plasticsGB/T 15048-1994硬質泡沫塑料壓縮蠕變試驗方法Cellular plastics，rigid-Determination of compressive creepGB/T 15065-2009電線電纜用黑色聚乙烯塑料Black polyethylene compounds for wire and cabl

51、eGB/T 15223-2008塑料 液體樹脂 用比重瓶法測定密度Plastics - Liquid resins - Determination of density by the pyknometer methodGB/T 15234-1994塑料平托盤Plastics flat palletsGB/T 15560-1995流體輸送用塑料管材液壓瞬時爆破和耐壓試驗方法Standard test method for short-time hydraulic failure and resistance to constant internal pressure of the plastic

52、s pipes for the transport of fluidsGB/T 15568-2008通用型片狀模塑料(SMC)Sheet molding compound(SMC) for general purposesGB/T 15596-2009塑料在玻璃下日光、自然氣候或?qū)嶒?yàn)室光源暴露后顏色和性能變化的測定Plastics - Determination of changes in colour and variations in properties after exposure to daylight under glass，natural weathering or labora

53、tory light sourcesGB/T 15597.1-2009塑料 聚甲基丙烯酸甲酯（PMMA）模塑和擠塑材料 第1部分：命名系統和分類基礎Plastics - Poly(methyl methacrylate)(PMMA)moulding and extrusion materials - Part 1: Designation system and basis for specificationsGB/T 15662-1995導電、防靜電塑料體積電阻率測試方法Method of testing volume resistivity of conducting and antista

54、tic plasticsGB/T 15738-2008導電和抗靜電纖維增強塑料電阻率試驗方法Test method for resistivity of conducting and antistatic fiber reinforced plasticsGB/T 15876-1995塑料四面引線扁平封裝引線框架規范Specification of leadframes for plastic quad flat packageGB/T 15907-2008橡膠和塑料軟管 可燃性試驗方法Rubber and plastics hoses - Method of test for flammab

55、ilityGB/T 15908-2009塑料軟管及軟管組合件 液壓用織物增強型 規范Plastics hoses and hose assemblies - Textile-reinforced types for hydraulic applications - SpecificationGB/T 15928-2008不飽和聚酯樹脂基增強塑料中殘留苯乙烯單體含量的測定Reinforced plastics based on unsaturated polyester resins - Determination of residual styrene monomer contentGB/T

56、16167-2009救生艇殼體玻璃纖維增強塑料層合板技術條件Technical conditions of lifeboat glass fiber reinforced plastics laminateGB/T 16273.5-2002設備用圖形符號第5部分:塑料機械通用符號Graphical symbols for use on equipment-Part 5:Common symbols for plastic machineGB/T 16276-1996塑料薄膜粘連性試驗方法Test method for blocking of plastic filmGB/T 16288-2008塑料制品的標志Marking of plastics productsGB/T 1630.1-2008塑料 環氧樹脂 第1部分：命名Plastics - Epoxy resins - Part 1: DesignationGB/T 1632.1-2008塑料 使用毛細管粘度計測定聚合物稀溶液粘度 第1部分：通則Plastics - Determination of the viscosity of polymers in dilute sol