錫爐預防保養操作指示(精裝版)

1、 作業指導書 Work Instruction編號Ref NOPage: 1 of 15現時變更版次Current RevisionN/A發行Issued確認Checked批準 Approved2簽名Signature日期 Date型號Model所有型號通用All工序名稱Process錫爐預防保養操作指示 Wave solder machine maintenance instruction原材料Material碎布、酒精、機油、黃油 rag、alcohol、lube、butter設備,工具,儀器Equipment,Tooling, Devices風槍、抹布、螺絲刀、除銹劑 fan gun、r

2、ag、screwdriver、the liquid of cleaning rust作業條件Condition室溫 room temperature作業內容 Operating Content1. PURPOSE 目的:Bring up operation indicate that soldering prevent maintenance operation, protect soldering maintenance work from correct implement.對錫爐預防保養提出操作指示,保障錫爐保養工作正確執行.2. SCOPE范圍:This procedure is ap

3、plicable for all wave soldering machine for Flextronics (XiXiang) Co.Ltd.此指示適用于所有.有限公司生產在線使用的波峰焊錫爐3.DEFINITION定義:A- The part of needing to replace 檢查后需更換的配件B- The part of needing to replace after checking定期需更換的配件 4. REFERENCE參考文件:Wave soldering operation specification波峰焊錫爐操作說明書.5.RESPONSIBILITY職責:Re

4、quest soldering technician to prevent maintenance according to operation indicate.要求錫爐技術員按操作指示對錫爐進行預防保養. 6.PROCEDURE程序:6.1. Set up soldering prevent maintenance operation procedure.建立錫爐預防保養操作程序.6.1.1. Daily maintenance subject 日保養工作. Clean the soldering dross of the wave nozzle and soldering

5、both, and ensure the solder level is between the high mark and the low mark on the solder pot. Otherwise, add solder bar and record the result into PSTX-PCME-WI-056 enclosed form 01 (01) page2 in time. 控制項目Control PointN/A項目Item規格Spec控制方法Method本工程檢查頻率Process Frequency品質QualityN/AN/AN/AN/A工藝Process P

6、arameterN/AN/AN/AN/A安全作業要點Safety Control Point保養時要切斷電源，留意不要燙傷。同時注意酒精等易燃物品離開錫缸，預熱區三米以外，以防火災。環境保護要點EnvironmentControl Point廢抹布、廢松香水渣、廢錫渣按環保指引投放到相應的垃圾桶內。 Company Restricted 作業指導書 Work Instruction編號Ref NOPage: 2 of 15現時變更版次Current RevisionN/A發行Issued確認Checked批準 Approved2簽名Signature日期 Date型號Model所有型號通用Al

7、l工序名稱Process錫爐預防保養操作指示 Wave solder machine maintenance instruction原材料Material碎布、酒精、機油、黃油 rag、alcohol、lube、butter設備,工具,儀器Equipment,Tooling, Devices風槍、抹布、螺絲刀、除銹劑 fan gun、rag、screwdriver、the liquid of cleaning rust作業條件Condition室溫 room temperature作業內容 Operating Content清潔波峰噴嘴錫渣,并檢查錫位是否在指示刻度范圍之內，否則應及時添加錫條

8、，并將結果記錄于表格PSTX-PCME-WI-056附表01（01）第二頁上 (次/2H) 。. Clean the soldering dross of the solder pump and soldering both清潔錫泵及錫槽錫渣.(次/4H). Clean sprayer of the spray nozzle and crystal thing.清潔噴霧器噴嘴上的結晶物。(次/2H). Clean the sensor at come in and go out清潔出入口及傳感器.(次/1D). Clean the bru

9、sh of cleaning finger 清潔洗手指毛刷.(次/1D). Clean the limit solder quantity sensor清潔錫溫感應器.(次/1D). Clean the transport track and the finger清潔運輸鏈鋁軌及手指.(次/1D). Clean sundries of the pre-heat zone清潔預熱箱雜物.(次/1D). Clean the solder dross of the surrounding solder port清潔錫缸周圍的錫渣(次/1D).6

10、.1.1.10. Clean the cooling and exhaust fan清潔冷卻及排氣風扇(次/2D).1. Grease chain conveyor ring潤滑運輸鏈傳送機啤鈴. (次/2D).2. Clean the exhaust filter net of the spray清潔噴霧排氣濾網. (次/2D).3. Clean the box of depose soldering 清潔托盤內廢錫渣物.控制項目Control PointN/A項目Item規格Spec控制方法Method本工程檢查頻率Process Frequenc

11、y品質QualityN/AN/AN/AN/A工藝Process ParameterN/AN/AN/AN/A安全作業要點Safety Control Point保養時要切斷電源，留意不要燙傷。同時注意酒精等易燃物品離開錫缸，預熱區三米以外，以防火災。環境保護要點EnvironmentControl Point廢抹布、廢松香水渣、廢錫渣按環保指引投放到相應的垃圾桶內。 Company Restricted 作業指導書 Work Instruction編號Ref NOPage: 3 of 15現時變更版次Current RevisionN/A發行Issued確認Checked批準 Approved2

12、簽名Signature日期 Date型號Model所有型號通用All工序名稱Process錫爐預防保養操作指示 Wave solder machine maintenance instruction原材料Material碎布、酒精、機油、黃油 rag、alcohol、lube、butter設備,工具,儀器Equipment,Tooling, Devices風槍、抹布、螺絲刀、除銹劑 fan gun、rag、screwdriver、the liquid of cleaning rust作業條件Condition室溫 room temperature作業內容 Operating Content6.

13、1.1.14. Solder pot maintenance and circumstances restoring錫爐內外部清潔整理及周邊環境復原(次/1D).6.1.2. Weekly maintenance subject周保養工作內容:. Clean flow wave back plate and adjust height清潔回流波后擋板及調整高度.. Clean the apparatus of flux spraying.清潔松香噴霧器組件.. Clean/dismount the sprinkle-nozzle清潔/拆開噴霧噴嘴6.1

14、.2.4. Clean finger and change清潔手指及更換新品(A). . Clean the viewing windows illumination inside清潔機器內部照明燈. Clean oxides of chip wave and bearing.清潔噴射波錫泵及錫槽氧化物.. Clean mesh and the bottom of the preheat zone.清潔預熱箱底盤及網孔. Solder' pot maintenance and circumstances restoring錫爐內外

15、部清潔整理及周邊環境復原.. Test the lathe & adjust it and record it.試車、調整并記錄.6.1.3. Monthly maintenance subject月保養工作內容:. Clean oxides of main wave.清潔主流波錫泵及錫槽氧化物.控制項目Control PointN/A項目Item規格Spec控制方法Method本工程檢查頻率Process Frequency品質QualityN/AN/AN/AN/A工藝Process ParameterN/AN/AN/AN/A安全作業要點Safety Co

16、ntrol Point保養時要切斷電源，留意不要燙傷。同時注意酒精等易燃物品離開錫缸，預熱區三米以外，以防火災。環境保護要點EnvironmentControl Point廢抹布、廢松香水渣、廢錫渣按環保指引投放到相應的垃圾桶內。) Company Restricted 作業指導書 Work Instruction編號Ref NOPSTX-PCME-WI-056Page: 4 of 15現時變更版次Current RevisionN/A發行Issued確認Checked批準 Approved2簽名Signature日期 Date型號Model所有型號通用All工序名稱Process錫爐預防保養

17、操作指示 Wave solder machine maintenance instruction原材料Material碎布、酒精、機油、黃油 rag、alcohol、lube、butter設備,工具,儀器Equipment,Tooling, Devices風槍、抹布、螺絲刀、除銹劑 fan gun、rag、screwdriver、the liquid of cleaning rust作業條件Condition室溫 room temperature作業內容 Operating Content. Clean the dirty things of pre-heater and tes

18、t the pre-heat tube.清潔預熱區雜物并檢查發熱管 (A). Clean finger cleaner and bath replace brush.清潔手指清洗器溶劑槽及更換毛刷.(B). Clean and change every windpipe 清潔和更換各抽風管道(B). Add Lubricate for all bearings. 給所有軸承加潤滑脂. Solder' pot maintenance and circumstances restoring錫爐內外部清潔整理及周邊環境復原.6.1.3.

19、7. Test the lathe & adjust it.試車、調整.6.1.4. Quarterly maintenance subject季度保養工作內容:. Clean radiator fan and check electric controller.清潔散熱風扇及檢查電氣控制箱.. Replace foaming pipe and windpipe.更換噴霧器氣管.(B). Check conveyer width and incline angle can be freely adjusted. 檢查導軌升降系統和調寬系統6.1

20、.4.4. Check bath in/out, up/down adopt motor drive system.檢查錫爐進出及升降系統 . Wave soldering inside maintenance and circumstances restoring錫爐內外部清潔及周邊環境復原.. Test the lathe & adjust it.試車及調整.控制項目Control PointN/A項目Item規格Spec控制方法Method本工程檢查頻率Process Frequency品質QualityN/AN/AN/AN/A工藝Process Pa

21、rameterN/AN/AN/AN/A安全作業要點Safety Control Point保養時要切斷電源，留意不要燙傷。同時注意酒精等易燃物品離開錫缸，預熱區三米以外，以防火災。環境保護要點EnvironmentControl Point廢抹布、廢松香水渣、廢錫渣按環保指引投放到相應的垃圾桶內。SOP 4-1 FORMI (00) Company Restricted 作業指導書 Work Instruction編號Ref NOPage: 5 of 15現時變更版次Current RevisionN/A發行Issued確認Checked批準 Approved2簽名Signature日期 Da

22、te型號Model所有型號通用All工序名稱Process錫爐預防保養操作指示 Wave solder machine maintenance instruction原材料Material碎布、酒精、機油、黃油 rag、alcohol、lube、butter設備,工具,儀器Equipment,Tooling, Devices風槍、抹布、螺絲刀、除銹劑 fan gun、rag、screwdriver、the liquid of cleaning rust作業條件Condition室溫 room temperature作業內容 Operating Content6.1.5. Half a year

23、 maintenance subject半年保養工作內容:. Examine heater connection in solder bath.檢查錫爐內的發熱管連線(B).. Replace bearing of solder pump.更換錫泵的軸承(B). Examine heater connection in preheating box.檢查預加熱箱內的發熱管連線. Cleaning finger chain drive and motor maintenance.清潔手指運輸鏈驅動器及馬達保養.. Cleani

24、ng Finger pump.清潔手指泵.. Cleaning sirocco motor and maintenance.清潔熱風馬達及保養.. Wave soldering inside maintenance and circumstances restoring.錫爐內部清潔整理及周邊環境復原.. Test the lathe and adjust it試車及調整.6.1.6. Yearly maintenance subject年保養工作內容:. Replace temperature control pin of solder

25、 bath.更換錫槽的錫溫控制針.(B). Replace preheated heat.更換預熱棒.(B). Replace heat of solder pot.更換錫缸發熱棒.(B)控制項目Control PointN/A項目Item規格Spec控制方法Method本工程檢查頻率Process Frequency品質QualityN/AN/AN/AN/A工藝Process ParameterN/AN/AN/AN/A安全作業要點Safety Control Point保養時要切斷電源，留意不要燙傷。同時注意酒精等易燃物品離開錫缸，預熱區三米以外，以防火災。環境保

26、護要點EnvironmentControl Point廢抹布、廢松香水渣、廢錫渣按環保指引投放到相應的垃圾桶內。 Company Restricted 作業指導書 Work Instruction編號Ref NOPSTX-PCME-WI-056Page: 6 of 15現時變更版次Current RevisionN/A發行Issued確認Checked批準 Approved2簽名Signature日期 Date型號Model所有型號通用All工序名稱Process錫爐預防保養操作指示 Wave solder machine maintenance instruction原材料Material碎

27、布、酒精、機油、黃油 rag、alcohol、lube、butter設備,工具,儀器Equipment,Tooling, Devices風槍、抹布、螺絲刀、除銹劑 fan gun、rag、screwdriver、the liquid of cleaning rust作業條件Condition室溫 room temperature作業內容 Operating Content. Complete checking module inlet of controller.檢查電氣控制箱內所有電控組件.. Solder' pot maintenance and cir

28、cumstances restoring錫爐內外部清潔整理及周邊環境復原.. Test the lathe and adjust it試車及調整.7. Wave Solder Finger PM Instruction/波峰鏈爪保養方法指示7.1. Fingers must be repaired/changed under below conditions.在以下的情況需要維修和更換鏈爪(1) The fixing part of the finger is distortion or worn out.鏈爪的固定位發生變形,或磨損.(2) The feet of the fi

29、ngers are distortion or broken (refer to picture 1 to picture 5). 鏈爪的兩個腳變形或者損壞(參考圖1圖5)。 Normal/ 正常 Picture 1/圖1 Picture 2/圖2 Picture 3/圖3 控制項目Control PointN/A項目Item規格Spec控制方法Method本工程檢查頻率Process Frequency品質QualityN/AN/AN/AN/A工藝Process ParameterN/AN/AN/AN/A安全作業要點Safety Control Point保養時要切斷電源，留意不要燙傷。同時

30、注意酒精等易燃物品離開錫缸，預熱區三米以外，以防火災。環境保護要點EnvironmentControl Point廢抹布、廢松香水渣、廢錫渣按環保指引投放到相應的垃圾桶內。 Company Restricted 作業指導書 Work Instruction編號Ref NOPage: 7 of 15現時變更版次Current RevisionN/A發行Issued確認Checked批準 Approved2簽名Signature日期 Date型號Model所有型號通用All工序名稱Process錫爐預防保養操作指示 Wave solder machine maintenance instructi

31、on原材料Material碎布、酒精、機油、黃油 rag、alcohol、lube、butter設備,工具,儀器Equipment,Tooling, Devices風槍、抹布、螺絲刀、除銹劑 fan gun、rag、screwdriver、the liquid of cleaning rust作業條件Condition室溫 room temperature作業內容 Operating ContentPicture 4/ 圖4 Picture 5/ 圖57.2. Details refer to machine operation instruction詳細保養方法參照設備操作說明書. 8.Ma

32、intaining Notices 保養注意事項 8.1. Maintaining machines only when the convey belt was shutting down將機器的傳帶關掉后才能對機器進行保養. 8.2.If the machine which need to be maintained is near to Solder Oven, air ventilated equipment should be installed before maintaining, so that the gases contains solder which brought ou

33、t by the process ofmaintaining can be taken away.保養前, 在機器靠近錫爐附近的地方應要安裝抽風棚, 將保養時產生大量的含錫氣體排走. 8.3. Only the qualified employees can maintain machines.只有受過培訓的人員才能進行保養. 8.4. Maintaining operators must wear prevented-heat gloves, goggles and highly effective gauze mask while maintaining machines.保養時, 保養人

34、員一定要戴上防熱手套, 護目鏡, 高效過慮口罩. 8.5.During the maintaining, solder residue and other chemicals should be classified and transported to the specified area to get dispose. 在保養過程中, 將錫渣及其它化學品做好分類, 并送到公司專門的地方進行統一處理.控制項目Control PointN/A項目Item規格Spec控制方法Method本工程檢查頻率Process Frequency品質QualityN/AN/AN/AN/A工藝Process

35、ParameterN/AN/AN/AN/A安全作業要點Safety Control Point保養時要切斷電源，留意不要燙傷。同時注意酒精等易燃物品離開錫缸，預熱區三米以外，以防火災。環境保護要點EnvironmentControl Point廢抹布、廢松香水渣、廢錫渣按環保指引投放到相應的垃圾桶內。 Company Restricted 作業指導書 Work Instruction編號Ref NOPage: 8 of 15現時變更版次Current RevisionN/A發行Issued確認Checked批準 Approved2簽名Signature日期 Date型號Model所有型號通用A

36、ll工序名稱Process錫爐預防保養操作指示 Wave solder machine maintenance instruction原材料Material碎布、酒精、機油、黃油 rag、alcohol、lube、butter設備,工具,儀器Equipment,Tooling, Devices風槍、抹布、螺絲刀、除銹劑 fan gun、rag、screwdriver、the liquid of cleaning rust作業條件Condition室溫 room temperature作業內容 Operating Content 9. RECORD記錄:Record Description記錄描

37、述Maintenance by維護職任Retentions Time(Min)至少保存期限Obsolete Disposition過期處理PSTX-PCME-WI-056附表01（02） Wave soldering daily maintenance record 錫爐每日保養記錄表Equipment Engineering /設備工程部1 year / 1年Shredding/撕碎處理PSTX-PCME-WI-056附表02（02） Wave soldering weekly maintenance record 錫爐每周保養記錄表Equipment Engineering /設備工程部1

38、 year / 1年Shredding/撕碎處理PSTX-PCME-WI-056附表03（01） Wave soldering monthly maintenance record 錫爐每月保養記錄表Equipment Engineering /設備工程部1 year / 1年Shredding/撕碎處理PSTX-PCME-WI-056附表04（01） Wave soldering quarterly maintenance record 錫爐每季度保養記錄表Equipment Engineering /設備工程部1 year / 1年Shredding/撕碎處理PSTX-PCME-WI-05

39、6附表05（01） Wave soldering half a year maintenance record 錫爐每半年保養記錄表Equipment Engineering /設備工程部1 year / 1年Shredding/撕碎處理PSTX-PCME-WI-056附表06（01） Wave soldering yearly maintenance record 錫爐每年保養記錄表Equipment Engineering /設備工程部1 year / 1年Shredding/撕碎處理10. FLOWCHART 流程圖: N/A控制項目Control PointN/A項目Item規格Spe

40、c控制方法Method本工程檢查頻率Process Frequency品質QualityN/AN/AN/AN/A工藝Process ParameterN/AN/AN/AN/A安全作業要點Safety Control Point保養時要切斷電源，留意不要燙傷。同時注意酒精等易燃物品離開錫缸，預熱區三米以外，以防火災。環境保護要點EnvironmentControl Point廢抹布、廢松香水渣、廢錫渣按環保指引投放到相應的垃圾桶內。 Company Restricted 作業指導書 Work Instruction編號Ref NOPage: 9 of 15現時變更版次Current Revisi

41、onN/A發行Issued確認Checked批準 Approved2簽名Signature日期 Date型號Model所有型號通用All工序名稱Process錫爐預防保養操作指示 Wave solder machine maintenance instruction原材料Material碎布、酒精、機油、黃油 rag、alcohol、lube、butter設備,工具,儀器Equipment,Tooling, Devices風槍、抹布、螺絲刀、除銹劑 fan gun、rag、screwdriver、the liquid of cleaning rust作業條件Condition室溫 room t

42、emperature作業內容 Operating Content 11. ATTACHMENT 附件: 控制項目Control PointN/A項目Item規格Spec控制方法Method本工程檢查頻率Process Frequency品質QualityN/AN/AN/AN/A工藝Process ParameterN/AN/AN/AN/A安全作業要點Safety Control Point保養時要切斷電源，留意不要燙傷。同時注意酒精等易燃物品離開錫缸，預熱區三米以外，以防火災。環境保護要點EnvironmentControl Point廢抹布、廢松香水渣、廢錫渣按環保指引投放到相應的垃圾桶內。

43、 Company Restricted 作業指導書 Work Instruction編號Ref NOPage: 10 of 15現時變更版次Current RevisionN/A發行Issued確認Checked批準 Approved2簽名Signature日期 Date型號Model所有型號通用All工序名稱Process錫爐預防保養操作指示 Wave solder machine maintenance instruction原材料Material碎布、酒精、機油、黃油 rag、alcohol、lube、butter設備,工具,儀器Equipment,Tooling, Devices風槍、

44、抹布、螺絲刀、除銹劑 fan gun、rag、screwdriver、the liquid of cleaning rust作業條件Condition室溫 room temperature作業內容 Operating Content 控制項目Control PointN/A項目Item規格Spec控制方法Method本工程檢查頻率Process Frequency品質QualityN/AN/AN/AN/A工藝Process ParameterN/AN/AN/AN/A安全作業要點Safety Control Point保養時要切斷電源，留意不要燙傷。同時注意酒精等易燃物品離開錫缸，預熱區三米以外

45、，以防火災。環境保護要點EnvironmentControl Point廢抹布、廢松香水渣、廢錫渣按環保指引投放到相應的垃圾桶內。 Company Restricted 作業指導書 Work Instruction編號Ref NOPage: 11 of 15現時變更版次Current RevisionN/A發行Issued確認Checked批準 Approved2簽名Signature日期 Date型號Model所有型號通用All工序名稱Process錫爐預防保養操作指示 Wave solder machine maintenance instruction原材料Material碎布、酒精、機

46、油、黃油 rag、alcohol、lube、butter設備,工具,儀器Equipment,Tooling, Devices風槍、抹布、螺絲刀、除銹劑 fan gun、rag、screwdriver、the liquid of cleaning rust作業條件Condition室溫 room temperature作業內容 Operating Content 控制項目Control PointN/A項目Item規格Spec控制方法Method本工程檢查頻率Process Frequency品質QualityN/AN/AN/AN/A工藝Process ParameterN/AN/AN/AN/A

47、安全作業要點Safety Control Point保養時要切斷電源，留意不要燙傷。同時注意酒精等易燃物品離開錫缸，預熱區三米以外，以防火災。環境保護要點EnvironmentControl Point廢抹布、廢松香水渣、廢錫渣按環保指引投放到相應的垃圾桶內。 Company Restricted 作業指導書 Work Instruction編號Ref NOPage: 12 of 15現時變更版次Current RevisionN/A發行Issued確認Checked批準 Approved2簽名Signature日期 Date型號Model所有型號通用All工序名稱Process錫爐預防保養操作指示 Wave solder machine maintenance instruction原材料Material碎布、酒精、機油、黃油 rag、alcohol、lube、butter設備,工具,儀器Equipment,Tooling, Devices風槍、抹布、螺絲刀、除銹劑 fan gun、rag、screwdriver、the liquid of cleaning rust作業條件Condition室溫 room temperature作業內容 Opera